BMW E36 Bee-r Rev Limiter Install (2 Step Launch Control)

How-to install a bee-r rev limiter on your E36, this example is for an obd1 BMW 325 with an M50. M52/328 install is slightly different (crank signal instead of coil pack power). Good for when your chip tune revs to the moon with no easy way of turning it down.
IG: @aco.b

[@aco.b]

!!Please read!! This setup is ONLY relevant for OBD1 325 e36s, I cannot comment on any other model or chassis. If you do not understand the very basic wiring diagram I recommend you DO NOT perform this install as you may damage your engine.

[@huntercongdon80]

Dude I can wrap my head around a single thing your saying bro 😂 I need Help

[@e36ayden]

post a 2 step video

[@JQNAH]

1:21 that was musical

[@maxfauzakis5317]

where did you buy it. because I had taken one and it didn't work

[@iroyal7684]

So I installed my bee r limter but when I 2 step it doesn’t shoot any flames, only acts like rev limter but only when I floor it and past the rpm limit and let go it shoots flames. Maybe bad wiring?

[@e436.]

Can you help me install it for my e36 ❤

[@BMWiE36]

Maybe try changing your gain, if you havent then try to put it on F

[@_lifeon1wheel_]

What wires did you hook it up to?

[@iroyal7684]

Any update video?

[@markpirkhoffer428]

Have you get any knowledge on fitting one of these to a obd 2 bmw z4 2.2i? Have gone through the cam shaft position sensor and the rev counter in the obd wiring but it throws out O2 sensor codes ?

[@Ifmarker07]

Does it work on all cars?

[@akramziyad8877]

Sorry, I would like to ask for instructions for installation on the bmw e30 engine m40.

[@pixelll]

Why go through a relay instead of straight to coilpack / crank sensor signal wire?

[@Kayzo_123]

what's your wheel size/fitment?

[@risingz3366]

Hi, maybe you can help me, I got a M52B25 and I can't get the bee R to work :/ Got the RPM signal as well on pin 20, and the other signal I tried to get from the Crank shaft sensor... Pin 83.. But it doesn't work... It recognizes the rpm but doesn't cut there :/

[@nsjb_tj8341]

How did you wire the bee r with a relay?

[@Bruno2204]

On which site did you buy this thing?

[@anukasamarakoon4284]

I’m wondering too

[@jeppelampe4103]

What relay do you use. I can not get mine to activate a relay

[@mi60100]

Where can i buy one

[@_lifeon1wheel_]

Anyone ever get this hooked up on there e36? I have a 99 z3 2.5

[@Bahmanson]

Which model of bee-r did u used ?

[@nsjb_tj8341]

I’m so confused pleaseee helppp

[@PreciousSandayan]

where do i put the wiring on the ignitions POSTIVE.NEGATIVE.SIGNAL?

[@Darkaccent]

Clean 36 mate

[@africasquad1060]

A potential great video but the explanation is all over the place

[@baggedtuned8569]

RIP imai san

[@francoispourchier1353]

hello can you make a new video easier to understand the girl its not well tidy and the photos are blurry plus I don't understand English well it would be good there is no video in French for the e36 can you master one French subtitles

[@Bye401K]

aaaaand....3..2..1, kiss your valves good bye.

[@Daniel240sx]

Its not cutting the Injectors Its cutting the spark so Its harmless unless you abuse it

[@olivierstevens4134]

Why woud jou ruin a nice e36 with this crapp. Just get a decent tune or stand alone managment system.

[@96Caleb96]

You kids ruin the point of the car community and our shitboxes haha, "car guys" used to not care about trying different sometimes obnoxious things on cheap cars.