E: "That's for like a a treasure chest dude" K: "Maybe it unlocks the secret to 3rd gear" BWAHAHA
@thatautogarage36444 жыл бұрын
VictorT_Media I literally read this comment as this part of the video was playing, 3rd Gearception
@MOTO8094 жыл бұрын
I got a good solid laugh out of that.
@SteveLowe654 жыл бұрын
Came to the comments looking for this. 🤣
@shize9ine4 жыл бұрын
E is the only person i've seen on YT money shift a sequential XD
@Timberwolf694 жыл бұрын
I was about to grab my glass for some hydration when this came. I don't know why I briefly heasitated doing it, but it saved me from spilling my drink all over my keyboard.
@OFWGKillDaniel4 жыл бұрын
With all those parts on the back of the crank being misaligned, I’d pull the pan and check the thrust bearing in the motor while it’s all out. Just to be safe.
@horderelations40414 жыл бұрын
ABSOLUTELY! This needs a bump to the top comments!
@zaksuzuki4 жыл бұрын
Check all bearings and probably bent the input shaft to
@jonasthemovie4 жыл бұрын
Or slap it all together with the dovels and half of the bolts.
@Laminur4 жыл бұрын
+1 this. Easy to do for the peace of mind.
@Snarf_Le_Wombat4 жыл бұрын
Crank walk the dog like a 4g63
@Binford25004 жыл бұрын
"I want to clean it up and finalize it later..". So its permanent, huh?
@PSNxFTWxRAGOI4 жыл бұрын
$10 bet that its going to stay the same in a year lmao
@damiendoisher78124 жыл бұрын
We all know it lmao
@brotherhood_ofstreetracers42684 жыл бұрын
Binford2500 disappointing but yea.
@hybridEP34 жыл бұрын
Kyles a fking hack lol
@UCCLdIk6R5ECGtaGm7oqO-TQ4 жыл бұрын
There are few things in life more permanent than a temporary solution.
@280zone4 жыл бұрын
"If it's leaking there is still some in there" Spoken like a true motorhead.
@guildensteinfoutch62324 жыл бұрын
If its leaking oil. Its got oil lol. Seen that posted on a page the other day lmao.
@wesley85994 жыл бұрын
Honestly too true. Leaking oil is still oil
@_Professor_Oak4 жыл бұрын
Just scoop it up with a cup and chuck it back in the engine, no point wasting good oil now
@johngonsoulin74134 жыл бұрын
A common saying with military helicopters too 😅
@brandonfloyd63214 жыл бұрын
Remember when you closed the engine to the transmision gap with the bolts? Probably busted pilot bushing then.
@whidden19984 жыл бұрын
Second this
@dsshowerpan4 жыл бұрын
Thirded
@PSNxFTWxRAGOI4 жыл бұрын
Forthdeded this
@rsharney11114 жыл бұрын
4th, saw that and knew they'd be back in there sooner than later
@gsppuffer4 жыл бұрын
Without a doubt
@russrtspooling77024 жыл бұрын
At least these guys are consistent. The horse power matches the amount of times they pull the motor. lol
@dougn64654 жыл бұрын
Its apart of it at this power level
@The_Chosen_None_4 жыл бұрын
@@dougn6465 Nah dude, everything they rush ends up breaking. That's the name of this game.
@russrtspooling77024 жыл бұрын
@@dougn6465 when you use a weak platform it happens regularly
@1991CALYPSO4 жыл бұрын
Hack shit together and this is what you get.
@DeAndre_20004 жыл бұрын
russrt spooling what would you call a strong platform
@CainSample4 жыл бұрын
I dont think all these things " come loose" ....they're just never tightened to begin with 😂
@Gearedweird224 жыл бұрын
No dowels definitely does that
@zaksuzuki4 жыл бұрын
its classic boosted boiz, half done stuff never patient enough to finish before going for a rip or forgetting to tighten stuff up.
@stoker204 жыл бұрын
Little dab will dew ya.
@wilsoncrocker4 жыл бұрын
theyre just posturing for that loc-tite sponsorship lol
@iNegroTv4 жыл бұрын
@@zaksuzuki I don't blame them when everyone is screaming at them to get everything finished rapidly. Shit happens, but luckily for them they have the money and support to fix problems
@TheManistheshit4 жыл бұрын
When they said the van was leaking oil the first thing that came to mind was the oil filter. Remember who put the oil filter on
@bugboyaidan77334 жыл бұрын
TheManistheshit genius thinking my guy
@griffinmackenzie4 жыл бұрын
🤣🤣🤣
@imalec4 жыл бұрын
💨 💨 💨
@MrTheHillfolk4 жыл бұрын
My buddy drove his Toyota pick up all spring and summer with a really bad oil leak. he had a 25 mile round trip and he would put in about 3 quarts of oil a day. So one day after getting tired of it he looked underneath. He realized he could not remember the last time he had the oil changed, and it must have been a long time because the oil leak was a hole rotted in the filter 🤣🤣
@benjaminharvey86174 жыл бұрын
@@MrTheHillfolk no one cares
@seanpaul88894 жыл бұрын
Kyle: "Maybe it unlocks the secret to third gear..." Emilio: (laughing) "yeah well maybe if it does you'd be in luck!" LMFAOOO
@DjimiVidZ4 жыл бұрын
😂😂😂
@ngcolby4 жыл бұрын
Laughed, snorted, choked on my own spit...wife is looking at me funny now...
@djpickle684 жыл бұрын
Cracked up.....
@zacksan00214 жыл бұрын
Would be great for someone's build to actually have a steering wheel in the straight position while going straight
@SirVic424 жыл бұрын
Then how would he know which way to turn when doing a wheelie?
@armedziak4 жыл бұрын
@@SirVic42 Some ducktape in the middle of the wheel would help
@tiddiesprinkles4 жыл бұрын
Asking way too much
@backyardboostin99084 жыл бұрын
These guys a kings of not finishing builds
@lpe6554 жыл бұрын
I have so much respect for the ole man at S1 build. He has forgot more about AWD than most will ever know.
@trainer0934 жыл бұрын
He knows his shit, really smart guy
@ChrisG13924 жыл бұрын
"If it's leaking oil that means it's still got oil in it." Good to go then lol
@ronjones-69774 жыл бұрын
"Vicious coupler attacks Boosted Boiz while they try their hardest to acquire The Rona."
@SirVic424 жыл бұрын
TBH the Rowdyssey deserves a vicious coupler. Nothing tame about that build.
@Aschmorr4 жыл бұрын
The Rowdessey is immune to the Rona’
@SkinnyPedalMotorsports4 жыл бұрын
Hang that special key from the mirror so you’ll never lose the pathway to 3rd gear 🤘🏼
@TheScott2404 жыл бұрын
Way to make me feel old. When you said you were born in 96, that was a shocker. I was born in 81, I don't want to be an old man. Life goes quick and the older you get the quicker it seems that the years click away
@7travnasty9714 жыл бұрын
Can't believe you guys didn't have any dowels in there...I'm an amateur mechanic at best, and realized that was a pretty important aspect to my stuff going back together...You guys are playing with some pretty expensive parts to be cutting those kinds of corners, tighten up lol...Btw, I graduated from high school in June of '97...
@cacervantes684 жыл бұрын
HASTE LEADS TO WASTE!!! stop rushing stuff again lol. get max quality!
@Bacon6764 жыл бұрын
Holy moly Kyle, that alignment is atrocious on the Rowdyssey! Get that wheel straight boi
@shedman73064 жыл бұрын
Are you new to the channel?
@jonasthemovie4 жыл бұрын
That would demand them to actually loosen the tierod nuts, which means they will be forever loose.
@masterexploder68024 жыл бұрын
Need to rename this channel to Halfassedboiz.
@unclej49974 жыл бұрын
Master Exploder there’s a reason Brent is always saying “the Boosted Boiz way” lol
@Prado8054 жыл бұрын
Master Exploder Justin Colvin Foreal 🤣🤣🤣
@punisher84264 жыл бұрын
@Anonymous exactly
@slammysj4 жыл бұрын
@Prado805 Lol
@Bumblebee47884 жыл бұрын
Glad to hear you are adding oil pressure guages to your cars, I had the same problems back in the 90's with those brass "T's" , I made a distribution block out a chunk of aluminum, just drilled and tapped a " cross" with 2 small mounting holes on the edges so I could mount it on the fenderwell and run all my oil lines and senders to it. I think Summit makes one that's fancier but mine worked fine for what it was.
@QuickSiR4 жыл бұрын
Its like people in Florida don't understand what a lockdown and social distancing is. lol
@ronjones-69774 жыл бұрын
But they used hand sanitizer! lol Anyone shaking hands right now is just fucking stupid.
@hinds904 жыл бұрын
Same in Houston, Tx. It doesn't mean anything until it affects you personally.
@St1ngerGuy4 жыл бұрын
Only a matter of time before these dudes get the Covid. The virus travels up to 13 ft in the air and it doesn't take much to get it. I'm in FL right now and people really aren't taking it seriously. Bright side, real estate prices are about to drop.
@BBROPHOTO4 жыл бұрын
I think this every time I see these videos drop. Where I am, hospitals are having to choose between who lives and dies. Thousand and thousands of people have died here, where families cannot even say goodbye or attend their funerals. The blasé attitude is actually quite shocking and the fact they don't even make a serious mention in any of these videos is questionable.
@emeraldisle704 жыл бұрын
BBROPHOTO what city are you referring to that is so overwhelmed Dr’s are triaging who lives or dies?
@AKproXR4 жыл бұрын
That moment when I realize how young Kyle is, and how far he’s come up with his KZbin career in such a short time... such an awesome accomplishment.
@Ajallday10104 жыл бұрын
Definitely seems like an alignment issue but it seems like you guys have it figured out and on the right track again. You guys make me so proud honestly, you didn't let bs ruin your day you guys just brainstormed how you were gonna go about fixing it
@budgettech33984 жыл бұрын
Loved how you said "We have a sequential minivan" Kyle....best part of the video ....squad goals
Dowel pins always install them! I learned the hard way with a customers car back when I worked at Nissan on a rogue
@cooperchurch84184 жыл бұрын
cannabased as a tech, you put things together fast and sometimes forget things. its happened to everyone. flat rate is ass
@89hybrid884 жыл бұрын
If this was the first time he did something in haste that would be one thing.
@_jay_3764 жыл бұрын
@cannabased when you do a shit load of cvts and your flat rate sometimes you just forget it you swapped the dowel pins or not
@_jay_3764 жыл бұрын
Now I keep extras in my tool box for any time you can’t get them out of the old trans from being seized/stuck in
@MafiaboysWorld4 жыл бұрын
I would just solid mount everything on Hondaru and remove all the variables from engine/drivetrain movement. It's already going full drag spec so may aswell do it.
@MartijnPeek4 жыл бұрын
MafiaboysWorld solid mounts wouldn’t have prevented this though.
@harleydanforth59864 жыл бұрын
Anonymous even that wouldn’t work... it was the internals that we’re moving not the housings
@vaughanroberts17764 жыл бұрын
13K Views in half an hour . Cranking it . I tell everybody I meet to watch you guys .love your channel . Keep it reals bros
@Rinop3214 жыл бұрын
Always doing pulls when things are not ready or tightened down!! 🤦♂️🤣
@The10000lbGorilla4 жыл бұрын
How else are you supposed to know what needs tightening?
@diannecrawford99964 жыл бұрын
@@The10000lbGorilla by tightening every bolt before you leave. Obvs🙃
@tannershanksftw4 жыл бұрын
r/woosh
@deanmartin70894 жыл бұрын
should check the input bearing in the transmission, with the pilot bearing worn like it is, the input bearing will take the abuse.
@frankyalvarezhg32534 жыл бұрын
Same ol kyle low oil pressure and missing gears 😂😂😂
@jinsc95964 жыл бұрын
Instead of using a tee fitting or sandwich plate, why not use a vacuum distribution block as an oil distribution block? Vibrant makes a block with 6 1/8" NPT outlets and a 3/8 NPT inlet. You can run a single line to the oil block, mount your oil pressure sensor directly to the block (which also fixes your vibration issues and helps keep the sensor in tact), and run your turbo oil feed off of this block too. Looks a hell of a lot better than a sandwich plate, gets your sensor away from unnecessary vibrations, and gives you room to add an oil temp sensor further down the road without having to do anything other than pull a plug out of the block and screw the sensor in.
@trey65334 жыл бұрын
Even tho the shaft from the trans is new I would put a run out gauge on it to make sure its perfect.
@RingTuned4 жыл бұрын
I have seen this before the dowels will most likely solve your problem I saw it in a sbc V8 swapped tractor It would not cause any issue sitting there I the clutch worked great but as soon as you put load on it the torque would cause the engine in my case to shift just slightly enough to make things hit The owner ignored it for one event it said boom and blew the bell housing apart
@Nathan-gj8ch4 жыл бұрын
but why would anyone not run the dowels ?
@knowbull5hit5904 жыл бұрын
Nathan Fitzer forget to put em in most likely lol
@zaksuzuki4 жыл бұрын
@@Nathan-gj8ch because they couldnt find them, they re small and easily lost. Rather then wait til they had the dowels they said "sent it bruz" and forced the gearbox to the engine thinking all would be okay.
@dazaspc4 жыл бұрын
100% no dowels the cause with high HP. You can see the movement on the mounting faces. I strongly recommend installing the bell housing and clocking it up with a dial indicator to ensure it is concentric with the end of the crankshaft.
@zaksuzuki4 жыл бұрын
john maselli it’s all over KZbin sometimes I swear they half ass shit just for content. Everyone keeps watching so why not.
@eddominates4 жыл бұрын
Kyle's got the right idea, I'd agree. That quick rip with the loose mounts probably bumped it a little and made your clutch self-clearance a little. Good thing you guys caught it before any serious damage. Shit happens, but as shit goes, this dont smell that bad! Keep at it Emilio, I wanna see Hondaru rip it!
@Octopod404 жыл бұрын
Thank god y'all didn't blow up with low oil. Keep up the good work guy's and be safe, can't wait for the next videos.
@trill-taco4 жыл бұрын
Perfect timing my powers been out since 6 am and I can’t watch a boosted boiz without having a good laugh
@sPeCThaGod4 жыл бұрын
SAMEEEE
@markwallace52744 жыл бұрын
jdm noob you live in the south ? Storms was tough last night
@dannym51064 жыл бұрын
NC?
@arturo7624 жыл бұрын
R.I.P
@jerome71034 жыл бұрын
Chatt town?
@89hybrid884 жыл бұрын
So much for quarantined. Driving around to different shops.
@bhew74094 жыл бұрын
no idea why the US got hit so hard...
@kratcliffe56804 жыл бұрын
100% Allignment issue.... Maybe the box moved a smidge under load/launch.....either way, the dowel pins should address the issue! Good work guys #staysafe
@userpike4 жыл бұрын
I think you'll be fine just putting the Hondaru back together as long as you install the dowel pins. That why the trans shifted over a bit. Even torquing the trans to engine bolts to spec without the dowels installed it's going to shift under power. The dowel pins aren't just to aid in installing the trans to the engine, they are there to keep them aligned. Good luck!
@rsharney11114 жыл бұрын
If you twist a trans with no dowels and loose mounts, your probably going to need a new input shaft.
@jupo25304 жыл бұрын
Co out young statics channel hes done a video on the awd pinning the rear and welding bro ..🤙🤙🤙🤘💪
@TRIP5_GAMING4 жыл бұрын
"maybe that key unlocks the secret to get into 3rd gear" ... fucking hilarious!
@johnfuniciello92224 жыл бұрын
Try to pull the clutch alignment tool in and out slightly while slowly torquing clutch plate bolts to flywheel. Should be able to be pulled in and out easily (with your finger tips) after clutch is torqued. Then make sure the input shaft is fully inserted into pilot bearing before hitting the bell housing bolts with ratchet or an impact. If the bell housing bolts are used to pull the trans to the adapter plate, the term “properly aligned” kind of goes out the window lol Love you guys and the content, not meant as a hate comment.
@JD-rq7il4 жыл бұрын
Just going to throw this out there. I adapted a range rover driveshaft to fit my crv. I pinned the rear clutch pack to make it solid. Here is my old build thread on it and also here is a video of the rear working great. honda-tech.com/forums/honda-cr-v-element-156/new-me-cr-v-3091170/ Driveshaft stuff starts at post 145.
@JD-rq7il4 жыл бұрын
kzbin.info/www/bejne/eofFh5WIpNJ3ldk
@slow4door2784 жыл бұрын
Piston rings broken in now 😂
@mdstevens89894 жыл бұрын
Kyle is definitely the king of half assed whether building a car or shifting gears
@nkill64 жыл бұрын
It's a Colorado thing we never take anything seriously
@TKTmon4 жыл бұрын
lol I love that you guys got a pizza topper. NO ONE will give a second glance to a 1st gen odyssey with a pizza topper. ya'll got some serious stealth going on with this.
@arcadiagreen1504 жыл бұрын
at 4:15 of this boosted boiz video kzbin.info/www/bejne/hqu7lXyKf9-Kaa8 you can see that the engine doesnt just mate up with the trans, Emilio says " im just gonna suck it in with this bolt" good rule of thumb is to NEVER draw rotating assemblies together with nuts or bolts. They should mate up flush and fastened once together
@otm6464 жыл бұрын
Exactly. I'm absolutely flabbergasted they didn't use the dowel pins in that either.
@iantowers69724 жыл бұрын
They don't understand enough of how these things work properly that's why they are always redoing things etc .cut corners go round in circles!!!👍🏻😂
@brentspang90924 жыл бұрын
Seems like the input shaft on Hondaru's transmission isn't long enough.
@scooz144 жыл бұрын
Or the ID of the pilot bushing is larger the the od of the input shaft pilot
@charlesadkins33354 жыл бұрын
Could be maybe the shaft isn’t going thru all 3 disks
@rollerdragon4 жыл бұрын
if the pilot bearing/bushing weren't seeing enough of the input shaft, would it have been bashed up like that? off center (i.e.: no dowels ) would cause the edge of the disks grinding and do that to the bushing, if the input shaft makes 1/2" of penetration, it will work... the shaft isn't tapered at the bushing... with dowels, and a clutch alignment tool, the plates can't hit out of round... loose mounts added and that shaft/bushing union is the weakest link. but thats just my two cents on it, we all have ideas of what it could be... hell, I'm just glad they're all healthy!
@scooz144 жыл бұрын
@@rollerdragon that's why I think that it has to be either alignment or mis sized. The way that bushing is beat up, it has to have some engagement with the input shaft.
@hupondio4 жыл бұрын
I think they need to review the adapter plate
@ballievogel53854 жыл бұрын
The keys open Industrial DB Boards good fine lol. Keep ripping guys. Tello all the way from SA
@ZeroCool-vn9bd4 жыл бұрын
I just want to see an under the hood camera if you take it through emissions. The look on the testing staff's face when they see that turbo is going to be priceless.
@hazadus2u4 жыл бұрын
Kinda remember u guys having to draw the trans in using the bolts!!!back in a video before you left colorodo🤔
@mikesweet58484 жыл бұрын
Big upvote this is facts.
@iNubAlert4 жыл бұрын
That's a relatively normal thing to do but it eventually aligns and goes easier into place
@Burn3774 жыл бұрын
@@iNubAlert not if the dowel pins are missing..
@shedman73064 жыл бұрын
@@iNubAlert dont know what kind of shop you worked in but mating the trans with the bolts is a big no no.
@von...4 жыл бұрын
all she needs is some seafoam and she'll be rippin like new brother!
@GetBent520Az4 жыл бұрын
Von Hassen lmao
@GetBent520Az4 жыл бұрын
I did that with my del sol. And my friend said exactly what your comments says. It no longer runs now 😂
@TheVanderbone4 жыл бұрын
RNE Productions just from seafoam or from something else? I’ve seen one or two comments saying seafoam messed up their motor, but I’ve also done it on three different old ass motors and have seen decent results. My experience obviously isn’t gonna be everyone’s experience but a little $12 can helped my throttle response a lot on an old V8 and an old 4 banger that would both stumble when you blip the throttle.
@sffabrications38724 жыл бұрын
Skyler dude you have to remember there’s people who think it’s the fix all and bad luck with it. I’ve never had a failure with sea foam. I love all their products.
@TheVanderbone4 жыл бұрын
Fix N Fab Collision that’s true, it’s not a fix all, but unless you did something very wrong I don’t feel like seafoam would cause a catastrophic failure either you know? If the motor was already messed up in some way I’d understand but I personally just didn’t see how seafoam would cause a problem if it’s used right.
@MrSzero134 жыл бұрын
THE BUILDS love the channel/// but kyle i think you should put a Quick release in miss Rowdy ... i think it will make the inside pop, just by adding a black quick release steering wheel it would look so good , STAY SAFE GUYS !!.. oh and also i think you should also give the van a fresh coat of paint.. i know sleeper look.. BUT DAMn i think the van would loook so good with paint to
@quickdeuce4 жыл бұрын
LOL,, at 13:40 first time I've heard that comment since being transported from FOB to FOB in the CH46 and CH53 helicopters while in Iraq and Afghanistan.The birds leaked hydraulic oil like gangbusters, typically we'd find oil drips all over our gear ("kit" as the Brits call) and on the floor making hustling onto and off of them a challenge. When we'd report the leaks to the flight crews they'd give us the thumbs UP and say,, "We're good,, as long as it's leaking we have oil,, now GET the F**K off my bird!" ***** A huge THANK YOU, CUDO's and way too cool for those guys and gals of our American, British and Allied Forces who gutted it out and flew those awesome aircraft moving troops.
@griplimit4 жыл бұрын
Everyone be saying “stop rushing things, do it right”... it’s called content! If there were no problems it would be pretty boring.
@IvanGarcia-eu5un4 жыл бұрын
griplimit can’t say it better myself
@saebbi4 жыл бұрын
Have the clutch disks in the right orientation!
@shortbustravelz24234 жыл бұрын
I think you are on the right track suggesting trans not in alignment with the crank centre line. Perhaps measure to see if the adapter plate lines up. good luck!
@davidfloener75394 жыл бұрын
With the rush schedule and so many bolts to keep up with it looks like a fun full time job. Keep on rippin
@hybridEP34 жыл бұрын
Never seen a group of guys have so many issues all the time with Honda’s 🤷♂️
@iantowers69724 жыл бұрын
hybridEP3 cut too many corners bro you go round in circles fella.thats why they have issues all the time do it rite do it once!!!!👍🏻👍🏻🇬🇧👌🏻
@birdness4 жыл бұрын
That's what happens when you start pushing big power.
@TakeNoShift4 жыл бұрын
@@iantowers6972 Whats with the Union Jack?
@Matty.Hill_874 жыл бұрын
@@TakeNoShift my guess is he's from the UK 🤷♂️
@TakeNoShift4 жыл бұрын
@@Matty.Hill_87 I thought that, but then what does that have to do with doing it once and doing it right? Sounds a bit prejudiced.
@duviday4 жыл бұрын
Perhaps because you're not running a bloody air filter. Good job you get given these turbos
@MattBerrymotorsport4 жыл бұрын
I can't believe it either
@zaksuzuki4 жыл бұрын
It’s the entire engine that will suffer. It’s the most simple thing but I don’t understand why they never put them on. They think it will rob them of half a hp?
@MattBerrymotorsport4 жыл бұрын
@@zaksuzuki here's the funny thing, if you buy a pod filter that has a "bellmouth" inside the air filter you actually pick up HP by using one. That blue car in my DP is twin engine with identical combos front and rear, the rear engine has an air filter and makes 30 HP more. Take it off and the power drops lol go figure I stupidly designed the front turbo placement not to use an air filter before I rear about this and now I can't do anything about the power losses
@zaksuzuki4 жыл бұрын
Matt Berry sounds like a mental project. Seems like a lot of these Honda guys don’t run filters because they’re always using turbos that are way to large for top end or just design they’re manifolds poorly. But when you can run one I don’t understand why you wouldn’t, no negatives to it.
@MattBerrymotorsport4 жыл бұрын
@@zaksuzuki looks cool to see the wheel. That's about it
@iTzDaNiiLo4 жыл бұрын
I'm happy you guys went down to visit S1Built. Those guys are doing it B I G in the AWD scene.
@br4d1014 жыл бұрын
The flywheel pilot bush is probably worn or bearing on gearbox side is knackered! Only way them plates could of touched the side of the pressure plate! Had it happen on one of my trucks with the pilot bush worn-the shaft wobbled about and the clutch plate done exactly what yours has!
@EvanAxer4 жыл бұрын
What if the adapter plate has always been miss aligned and that was you shifting problems the whole time?
@BellaAndGiGi4 жыл бұрын
**VIRAL VIDEO** "STREET RACING PPL IN THE SLEEPER SOCCER MOM MINIVAN" (TOOK LAMBO TO GAPPLEBEES) 😂😂
@CraZYCODplayes4 жыл бұрын
Easily could be miss aligned with out using the dowel pins. The dowels are precision machined and used for the exact purpose of aligning mating surfaces. The flywheel and pressure plate align them selves to each other, the input shaft aligns the clutch plates and that placement of the input shaft is directly correlated to the dowel pin locations.
@alanloyd71644 жыл бұрын
Dowel pins in any mechanical device are not optional. That's an engineer's way of saying "these two things NEED to stay this way".
@sam_s_4 жыл бұрын
He said they had the dowels, but they did not install them, right? So they put it together without dowels? Or am I misunderstanding?
@MartijnPeek4 жыл бұрын
First Last they had dowels at one point, probably didn’t have them when assembling it this time. Because if they did have them that would’ve been stupid.
@e46fanatic544 жыл бұрын
Is the clutch disk in backwards?? I made that mistake before.
@crazyd13774 жыл бұрын
The key for unlock 3rd gear, hahahahahaaaa that's funny af kyle!
@thegenerousdegenerate93954 жыл бұрын
Not too bad though all things considered. They're both fresh builds these things are to be expected. All in all you two are faring pretty well. You just gotta purdy up that van a bit.
@Jcarney874 жыл бұрын
No dowel pins? Cmon. Dudes. Any cover u put on any case half’s any trans ANYthing like that u need dowel pins. Crucial.
@luckyej85594 жыл бұрын
Was just watching cleetus's new video and I got the notification for this so here I am. Sorry cleet!
@django24674 жыл бұрын
Same 🤣
@sethgt12344 жыл бұрын
Me too.
@ramseytruthbros77774 жыл бұрын
Same
@ShopTown4 жыл бұрын
Same 😂😂😂
@iantowers69724 жыл бұрын
Cleetus gone down shit pan for me abit now.not like he was too much bullshit stuff need more cars etc racing and that but anyways
@MJTAUTOMOTIVE4 жыл бұрын
All these are approximates $10000 transmission, $2000 clutch, $8000-$10000 engine. Doesn't bother with $2 dollar dowl pins to makes sure adapter plate is aligned with the engine. Then doesn't bother with $2 dollar dowl pins to align transmission with adapter plate. Puts engine in and there is gap between transmission and adapter plate, puts in bolts and uses them to close the gap to the transmission. When tightening the bolts to close the gap it was obviously misaligned, that has what caused the pilot Bush to crack and mushroom. And it also looks like the first clutch plate was in back to front that is why the back of the crank is messed up. And because everything was not aligned it has destroyed a big dollar clutch assembly. And possibly the thrust bearings in the engine. They can handle load from depressing the clutch all time. But not being squashed when tightening up a misaligned bellhousing. Then says we went for a ripp without the engine mounts not tight. I always love the videos and what Awesome things they build. But they have built enough of these things to know better. It just pisses me off when you see high dollar parts get destroyed for the sake of making a video. Could have taken more time, got a few more videos out of it and done it properly and not be rushed.
@justinbrossett49504 жыл бұрын
If the bellhousing separates from trans you could check the alignment with a dial bore gauge to make sure input shaft is centered
@smooth_ops29424 жыл бұрын
Oil line T fittings been killing turbo Honda's for years.
@rsharney11114 жыл бұрын
Dedicated lines only
@The10000lbGorilla4 жыл бұрын
@@rsharney1111 do you not run an oil pressure sensor? Or do you get oil feed elsewhere?
@antonop1004 жыл бұрын
This is the correct way www.theoldone.com/articles/oilpressure/
@brycerobbins8754 жыл бұрын
So close to a million subs, I’ve been here for a hot min apparently
@joserotary96364 жыл бұрын
Could have cruise by my house here in Ocala Florida lol. That engine is good. 💯👍🏽👍🏽👍🏽
@Herbsy4204 жыл бұрын
The dude from S1 Builds seem like the coolest guy ever!
@PistonAvatarGuy4 жыл бұрын
You guys were pretty rough mating the engine to the transmission, you may have bent the input shaft.
@gsppuffer4 жыл бұрын
Yeah used bolts to pull it together and them bushings are super weak
@chinolocko94294 жыл бұрын
Oh great! Now kyle cant even find 1st gear!
@shaunmilor4 жыл бұрын
Im 35... We used to go to a few different video rental places to get vhs tapes then longs drugs moved into town and had video racks at the front of the store for vhs tapes, then slowly they had some dvds, then redbox, and then the Internet... crazy how fast everything moved, I can remember getting dialup Aol Internet in 1994. to see a full page picture could take 10 minutes and a video could take hours to load
@daniellomeli9264 жыл бұрын
Damn you can hear Kyle was shitting bricks when oil pressure went low. I would have been bummed out too. Good catch though! 🙏🏻
@redsballer19044 жыл бұрын
I like how the description is just “close call”
@scottm98204 жыл бұрын
Receipt was printed the same day i was born!
@smooth_ops29424 жыл бұрын
Same day? If so you need to buy a oddesey 👍🏻
@Huda887544 жыл бұрын
My 9th birthday
@JDM98Ferio4 жыл бұрын
K-Tuned sells a short feed line adapter for the oil lines. Has the main port for the sensor and two ports to feed oil.
@mikegodowski49884 жыл бұрын
Bellhousing mis-alignment will chew a pilot bushing fast. Dowel pins are a must, and the bellhousing needs to be indexed to the crank via dial indicator. I'm pretty sure the spec for most clutches is 0- .005" runout. Lack of dowel pins caused this all day.
@Thecasualgamer-pp5wc4 жыл бұрын
5:27 lucky man kyle can finally hit 3rd
@thirdgenfreak254 жыл бұрын
Before it was 1,2,..... Red line!!! Lol
@seanstubbs26204 жыл бұрын
we don't want to here no more money shifts round here that sounds expensive
@southwestdesertfrenchies4 жыл бұрын
Hey bro I got a vc off a land rover I’m down to send y’all just pay for the shipping it’s the whole complete driveshaft
@lijahmack1114 жыл бұрын
Reggie Sanchez send it to me instead lol built h2b turbo crv
@southwestdesertfrenchies4 жыл бұрын
Lol I have a B20v turbo crv full build that’s why i have 2 of them and if I send you you it will not be free for them it will for the build and to support them
@bensmith47854 жыл бұрын
Input shaft is not reaching pilot bush propley. Said this at the beginning of project. Machine up a extension for input shaft and go to roller bearing pilot. Run dowls and always test fit and measure clutch plates position to gearbox splines.
@austinr85013 жыл бұрын
5:28 the best boostedboiz reference ever to be made
@JamesBonnd4 жыл бұрын
Once boostedboiz post then everything else have to wait for a while.. have to watch....
@RadDadisRad4 жыл бұрын
Lol. Says input shaft is brand new and it can’t be bent. I’ve seen lots of new stuff not be right.
@MrTheHillfolk4 жыл бұрын
Yea but no dowels .... That is probably what did it , and it coulda bent the input shaft but it's probably 🤞ok
@billbry4 жыл бұрын
When I was a rookie NASCAR driver, I unknowingly used a pilot bushing that was slightly too big and that happened. I always measured them closely after that experiance and eventually used a needle bearing pilot..
@Laner844 жыл бұрын
Emilio spots keys, Kyle " hopefully that's the key to 3rd gear!" 🤣 lucky spot there with the leaking oil too!
@thesauce22104 жыл бұрын
5:31 unlok the secret to get in 3 💀💀💀
@nibbzs154 жыл бұрын
I dont think Emilio gets enough money from these videos that's why hes always the last to finish his builds
@TheVanderbone4 жыл бұрын
nibbzs15 also things are super expensive with where they are at and things take time man. They buy a lot more high end parts now a Days compared to when I started watching this channel. They went from cranking up mostly stock Honda’s with a big turbo and an upgraded clutch to using sequential transmissions and built motors, etc. The BoostedBoiz are all grown up and I’m damn proud!
@mke7234 жыл бұрын
Subaru uses different sized pilot bearings/ bushings. Make sure the input shaft is the same as the pilot inner. I messed up a JDM trans input shaft seal using a USDM pilot bearing.
@danhard84404 жыл бұрын
in Minnesota when the car leaks oil like that we just call that rust prevention lol