Booster pumps for aquarium reverse osmosis systems - How to install and what are they for ?

[@tonyw7836]

I just watched 8 other videos on installing this pump. They all confused me. This one is straightforward and clear. Super easy to understand. Thank you for this great video.

[@lisademayo8589]

having some trouble. which way would you turn the screw on the booster to DECREASE the pressure coming out of the pump if it's too much?

[@BRStv]

You'll turn the set screw counter clockwise to decrease pressure. Just keep in mind that the screw will only do so much. If you need further pressure reduction, you may need a pressure reducing valve like this Watts valve. www.bulkreefsupply.com/watts-pressure-reducing-valve.html

[@andrewesquivel]

Dude, that was straight up exactly what I needed to know. Thank you very much

[@VinnyG919]

how's it different from common aquarium pumps?

[@paranoid1123]

If I have this pump and shut off do I still need the autoshut off on the ro membrane? And do I need to need to change the flow restriction?

[@BRStv]

You shouldn't need to change the flow restrictor unless you change the size of RO membrane that you're using. The job of the auto shut off valve is to cut the waste water from flowing when a float valve is triggered, so I would suggest leaving that on the system, even if you have a booster pump and pressure switch.

[@ReefMimic]

GREAT VIDEO !!! Have a link for showing the disassembly of the pump, maintenance parts, things to check, etc? Have a feeling either there is sediment in my pump ( even with a regular prefilter) or the shut off sensor needs to be adjusted.

[@mizerrocker]

Talked to Aquatac they told me to install pump after the three sediment filters and before the membrane then no need to buy extra sediment filter .

[@stuartsmith5274]

Hi I don't suppose you have a link for the power supply, mine just come with 2 wire, its a micro diaphragm pump, thanks

[@BRStv]

This is the link to the power supply for the Aquatec 8800 in this video www.bulkreefsupply.com/aquatec-power-supply-for-cdp-8800-pump.html

[@unwired]

Which is efficient the RO pump is feeding the RO membrane or put the booster pump before the first stage? (Before first stage there is a 5micron sediment filter) Source > Sediment > Booster Pump > First Stage.

[@Botzz28]

What’s the optimal psi for the rodi system ? In finding that my filter canisters are leaking from the top idk why 🤦🏻‍♂️

[@BRStv]

We usually suggest at least 50 PSI, but no greater than 90 PSI. If you're in that range and the canister is still leaking, there is probably an issue with the o-ring or the canister may not be tight.

[@ReefMimic]

correct me if im wrong. the pressure switch should be placed before the di resin ( if being used) stage correct?

[@vgasocal]

how does the booster pump activated? Do I keep it plug in 24/7 or only plug it in when I want to produce RODI water?

[@CatheadBiscuits]

Can someone answer this question?

[@bkbricks_]

Great video. We just moved and the preassure here isn't what I'm use to getting so I may look into one of these.

[@digitalreefs]

Hi guys. Never been able to get an answer to this.... i have an unmodified Vyair RO50MP. It works fine but when the float valve shuts off the flow, the pump starts back up again every 30 seconds or so and I can hear some waste water produced each time. It isn't a major issue but quite irritating as the unit is constantly clicking on and off. Is it supposed to this? As said, the unit works fine and does shut off... just the pump continues to 'cycle'. I've asked the manufacturer but never got a useful answer!

[@michaelisakov1108]

What's the optimal psi to run or rather max psi to run a 100gpd rodi system with a pump like this. As you mentioned these pumps come with 115psi from the factory and I dont want truin the rodi with such a high pressure but at the same token I want to have a pressure safe enough to get optimal product results without compromising the integrity of the system.

[@juliosantana2069]

im currently using my ro system for drinking water i have an aqutec pump and i seem to be having a little trouble with the tso valve it dosent kick in until the tank is empty i need it to kick in sooner so i dont run out of water i have it hooked up between the tank and last carbon filter

[@djdenv]

I see you installed this before all the prefilters. I've read elsewhere it should be installed directly before the ro membrane. Can you comment on that?

[@BEAULIQUIRE671]

Does adding a booster pump improve the rodi water to waste water ratio production since I didn't realize how much water actually gets wasted to make 1 gallon of rodi water?

[@migueltostado7184]

I have the 7-stage one, the pump is well connected but it does not turn off automatically 😬

[@BRStv]

Hey Miguel, There are a few things that could cause the booster pump to not turn off when your float or solenoid valve is triggered. There is probably too much info to share via a KZbin comment, but feel free to reach out to our customer service team if you'd like to troubleshoot this; we'd be happy to help! BRS Customer Service Phone: [phone] Email: [e-mail]

[@haivang1]

I can't find the pre-filter strainer for the connection before the booster pump on your guy web site? Will you show me on the BRS site?

[@Harlizzlee]

i would like to have at a minimum of 50 psi holding pressure (i have my ro going to my refrigerator ice maker, and the low pressure burned out the solenoid and i just replaced it, and now it's making ice). i have a booster pump and switch, which shuts off at 40psi. it'll drop to 20psi or lower before it starts up again. so, i turned the allen key but now it seems to run every 30 minutes to about 60 psi, but the pressure eventually drops to 40psi and starts up again. input is around 70psi. should i get a permeate pump? will this increase the holding pressure on the tank side? my tank is set to 7psi btw. thanks in advance!

[@dannyblackwell2426]

some put the booster pump before the membrain, but i have it like you did on this video, is there any difference were you put it

[@Verradonairun]

Will this device filter out salt from seawater as well? So that I'll be able to drink seawater? And can I run this with a car battery? Or better yet - can I run this manually, for instance with a bicycle pump, instead of using electricity?

[@xelucidx]

@BulkReefSupplyCom the highest i've seen it at ta constant rate has been 45 with everything off, no washer/shower/running taps etc.... but avg is around 35-40 id like to see at least 75-90 psi with the pump which im sure, but the 4 stage with DI can handle over that right? and the pump has a safety feature to not go over 115 right? i hope the pump helps a lot and im sure it will :)

[@blufgan]

What micron would you suggest for a prefilter before the pump?

[@viti339]

When you add the membrane upgrade kit, and have a flush kit installed, will both membranes be flushed. Due to tds creep when not used for a while. Thanks

[@Jayhawk2004]

I lost the auto shutoff pressure switch and now want to (automate) the system. Where can I buy a replacement?

[@antandbecksc]

Hi, I have a booster pump putting out 120psi, I don't have that adjusting screw to reduce pressure to my RO , is there any other way I can bring down psi, thank you.

[@xelucidx]

just purchased one today from you guys, and im burning through DI resin and my PSI is ~35-40 just wondering what PSI you would recommend for the best quality of product water

[@juliosantana2069]

my ro booster pump is working good but for some reason the pressure valve turns off before the ro auto shut valve turns off what can i do about that

[@thothgod985]

Hi. I have a Reverse Osmosis system that reads 60psi. Is that enough pressure for the 3/8" clean water line to reach a resevoir in the next room? or would I need a booster pump?

[@championx1]

I don't see those filter strainers available on the website...do you only carry the DM filter strainer for 8.99 now....? currently out of stock too

[@1997LT1Camaro]

Whats a safe max psi for a system? I have around 30-40psi normally. 95psi with booster on.

[@durangotang1681]

I need a pump that will pressurize water to 60 plus psi straight from a 330 gallon ibc tote with 0 input pressure. Please help!

[@familiajorgevalencia7940]

durangotang 1

[@vonerickberedo9372]

is the rodi aquatic life Twist in 100gpd 4 stage need this?

[@marioflores9450]

I thought it was after the carbon filter im i wrong? Im confused 😊

[@flyin20052005]

hi wjat do I do if the pump give to much pressure its giving me 100 psi how would I lower this

[@flyin20052005]

thanks a lot

[@DennisGambrell]

my water pressure varies 45 to 70 PSI so i have purchased the 8800 to maintain the recommended 65 plus PSI for water saver RO-DI BRS system. The RO-DI empties into holding tanks (1 fresh and 1 salt) and I would like to pump from basement to upstairs, first floor, to a shutoff valve . What pump would you recommend.

[@pashmin5990]

I like your Marine products & RO spare parts. is it possible to sheep to india directly or my relatives stay in NY they will carry.

[@יוחנןגברִיאל]

Hopefully someone can help. I purchased a booster pump with a pressure switch. I installed it exactly as shown but the booster pump continues running no matter if I tighten or untighten the screw on the pressure switch. Most all RO systems have the same configuration when installing the booster pump. I followed the instructions exactly. I am stumped. Any ideas anyone?

[@travusschlenker9710]

I’m having trouble with pressure with a booster pressure is at 40 all the time

[@Senorlatulla]

finally someone that can explain how this thing works!.... thank you for the video. Question: I have a 300gpd spartan rodi system, a what psi should it be at? and If I get the same pump you demonstrated (i believe it is a 8800), at what number should it be adjusted if I have to adjusted at all?

[@Senorlatulla]

thanks dude... so obviously the pump itself will have to be adjusted because of its factory settings (125psi, which can cause stress/leaks in the RODI system)

[@Senorlatulla]

thanx again... really great tutorial

[@tyte90]

Great video, straight to the point.

[@jonanderson6569]

BulkReefSupplyCom What is the optimal pressure for a single membrane setup. I’m running 90psi with a booster pump. To much?

[@bryanpena7268]

Man why is the hobby so dang expensive. I don't even have a reef set up yet and I feel overwhelmed from the costs of trying to keep up with this hobby. Recently my city changed how it treats our water and now I don't feel tap water is safe anymore for my fish. I get brief ammonia spikes after water changes and I treat my water with Seachem Prime which supposedly detoxifies ammonia and chloramines, I don't doubt the water conditioner works, I just believe my tap water has become far too toxic to use. I been looking at the BRS RO/DI 5 stage premium/premium plus 150GPD units but they're so expensive $269-$329 and I'd definitely need a booster pump which is +$100. Overall over $400 for a unit just so I can perform my water changes on a simple freshwater set up is just not cool. I do plan on setting up a planted/shrimp tank so the RO/DI will come in handy and maybe 2023 a reef set up after I recovered from spending so much in 2021 since at the moment I have all the gear necessary for my next 2 tank set ups. RO/DI unit is becoming very necessary as my current tank is 100 gallons and I change about 40 gallons a week so buying water at my local fish store is just not possible. I plan setting up a 55 gallon something? If not I will hold out on the 55 and wait until they release the 75 gallon on sale again. I have a 29 gallon and 20Long ready for a planted set up, just need to buy a stand for these 2 but I might look for metal rack since they are around the same size and will be similar set ups both using CO2

[@BRStv]

It might be worth considering an RO only system if you're using it for freshwater. We have a 4 stage RO only that has a single membrane (which might make a booster pump not necessary for you), which is much much less expensive than a system with all of the bells and whistles. Plus, you can always add on canisters later when you want to add DI resin for your future reef.

[@MiraiNoha]

thanks

[@a.roncarmichael6593]

all about the two components, but where is the how-to actually install in my existing system???

[@tharlowXY]

Very well explained.

[@pblogic007]

My pressure shows 60 when it's full and shut off by the float. When its producing it shows 40... The permeate pump makes that jump around. What shou

[@Th3mast3r69]

You guys are awesome.

[@xelucidx]

@BulkReefSupplyCom yes im also on a well lol

[@pblogic007]

I do?

[@honestabe4760]

No instructions don't know what to do out of top off water tanks gonna die thanks BRS

[@karelroobroeck4111]

You talk like trump... :)