Hello, is it mandatory to open and close the button for each startup or only once to configure the emulator.? Thank you.
@green13943 жыл бұрын
good clean job,,subscribed!
@CarLabImmoTechnicalChannel3 жыл бұрын
Thank you! 😉
@nicusorn41323 жыл бұрын
Сколько людей спрашивают про этот выключатель и ни один прямой ответ. Один раз использовать или постоянно? Буду смотреть другие эмуляторы от других производителей.
@CarLabImmoTechnicalChannel3 жыл бұрын
We constantly update our solutions to make them as easy to use as possible for our clients. We advise you to always follow the procedure in our instructions, because there is always the most up-to-date information. The video is quite old now, on page 2 of this manual you will find the procedure and the answer to your question: carlabimmo.com/manuals/immobilizers/renault/renault-with-can-ver2.pdf
@Simoprog6 жыл бұрын
Thanks good job
@CarLabImmoTechnicalChannel6 жыл бұрын
Thank you ! ;)
@jaroslavrezab27565 жыл бұрын
Diagnostic of the ECU and UCH in the car is possible after using emulator for both procedures (with or without switch). Thank you
@geocity263 жыл бұрын
Diagnostic has using K-line so that's possible
@Paolo-zm5ss6 жыл бұрын
Should the first start have to be made, must the switch remain permanently or do not need it afterwards?
@CarLabImmoTechnicalChannel6 жыл бұрын
carlabimmo.com/download/Julie_manual/Renault/Renault_with_can_ver2.pdf Go to page 9 - there is described another procedure without the switch
@agdoservice7 ай бұрын
Hello Good job ! Where l bit this emulator ? Congratulation.
@CarLabImmoTechnicalChannel7 ай бұрын
Hello! You can purchase it directly in our store: shop.carlabimmo.com/ Or from one of our official distributors: carlabimmo.com/partners
@perfautosportpassion90934 жыл бұрын
Same question as Paolo Gal, do I need te leave the switch ? permanently ON or do I have to do the same way as the first start ? OFF then ON ? Can I cut the wires ? I rade the page 9 of your document and I can't find the answer. Thank you for answering :)
@CarLabImmoTechnicalChannel4 жыл бұрын
Hi, please check the 2nd page of this manual, you can find there another options which you can use in the procedure: carlabimmo.com/manuals/immobilizers/renault/renault-with-can-ver2.pdf Hope it will be helpful. Anyway, if you want to use the switch you must leave it and use it everytime you start a car according to the procedure from 5:11
@marinossimillides8910 Жыл бұрын
did you remove 24c02 from the emulator as per manual ?
@CarLabImmoTechnicalChannel Жыл бұрын
Yes, if you don't make changes into 24C02 memory built into the emulator, it needs to be unsoldered.
@astroboy2astroboy2472 жыл бұрын
Hello mate, does the switch have to stay forever? or then once the emulator is configured the switch is not necessary thanks
@CarLabImmoTechnicalChannel2 жыл бұрын
If you do the procedure with the reset button then yes, you have to keep it. However, if you do the procedure from page 2 of this manual, you don't need to install it at all: carlabimmo.com/manuals/immobilizers/renault/renault-with-can-ver2.pdf
@Wild-Paw-XD4 жыл бұрын
Witam czy do opla omegi mogę takie coś zastosować?czy można uwas kupić?
@CarLabImmoTechnicalChannel4 жыл бұрын
Dzień dobry, żeby udzielić odpowiedzi potrzebujemy więcej informacji na temat auta i zamontowanego w nim sterownika. Najlepiej byłoby gdyby z tym pytaniem zwrócił się Pan do naszych Techników przez Forum Pomocy Technicznej: carlabimmo.com/newforum/viewforum.php?f=4
@Wild-Paw-XD4 жыл бұрын
@@CarLabImmoTechnicalChannel Siemens simtec 56.5
@michaelmisiewicz29383 жыл бұрын
Hi I have a vivaro 2 2006 with bosh 0 281 011 530 ecu will this device work with my ecu
@CarLabImmoTechnicalChannel3 жыл бұрын
The emulator will probably work with your ECU. Please check the instructions and make sure your ECU is the same as in the manual: Page 3 carlabimmo.com/manuals/immobilizers/renault/renault-with-can-ver2.pdf
@TECNICARMOTORSSPORT3 ай бұрын
hola el emulador tambien tengo que programarlo?
@CarLabImmoTechnicalChannel3 ай бұрын
Si, hay que instalar emulador de acuerdo con las instrucciones apropiadas. carlabimmo.com/instruction-manuals
@TheWerni217 жыл бұрын
Nie rozumiem z tym przełącznikiem na can L . Trzeba odpalać zawsze z wyłączonym a w trakcie pracy silnika włączać czy tylko raz ?
@CarLabImmoTechnicalChannel7 жыл бұрын
W programie Immo Bypass ta procedura została opisana w ten sposób: 1. Cut CAN L line from the ECU plug. 2. Put the switch-key inside the cabin by the ignition switch. 3. After inserting the key, disconnect with Can L switch and start the ignition. 4. Short it with Can L switch and start the car. 5. That is security switch for safety start car. Mam nadzieję, że powyższy opis będzie pomocny! Pozdrawiamy i życzymy miłego dnia!
@saleemhaulkhory82343 жыл бұрын
Hi. Where can I buy this from? Thank you. I need it for an edc16c3
@CarLabImmoTechnicalChannel3 жыл бұрын
You can buy our products in our store: shop.carlabimmo.com/ Before buying, remember to check if your ECU number is on the list of supported ECUs.
@LordBlick4 жыл бұрын
Is jumper config for black PCB same as for green?
@CarLabImmoTechnicalChannel4 жыл бұрын
We recommend to always check our online manual before using the Emulator: carlabimmo.com/manuals/main-page.pdf
@владжывогляд2 жыл бұрын
hello, what is the button for? is it possible to install an emulator without a button?
@CarLabImmoTechnicalChannel2 жыл бұрын
Yes, for emulators above version 103, this button is omitted in the procedure.
@arkadiuszkonwa92142 жыл бұрын
Dioda w emulatorze szybko miga, w czym jest problem?
@CarLabImmoTechnicalChannel2 жыл бұрын
Proszę sprawdzić według tego filmu na jaki problem wskazuje dioda: kzbin.info/www/bejne/hKOQhaqnbM94i5o Może Pan również skorzystać z naszej pomocy technicznej. Proszę zrobić post na na naszym forum i technik Panu pomoże: forum.carlabimmo.com/
@joshbennett62934 жыл бұрын
Hi if you don't edit the eeprom on the emulator does it need to be removed from the emulator or not thanks
Kess OBD, FGTech OBD or FLEX OBD are devices that read only a part of the FLASH memory, and we usually need the entire program, in particular EEPROM, to determine what values we need to enter into the Julie Emulator memory. Therefore, we recommend using these devices while reading the ECU on the table. We then read the entire program. If you have any problem, make a post on our Official Forum: forum.carlabimmo.com. Describe your problem, attach ECU pictures and ECU file and our technician will try to assist you.
@johanngarde6962 жыл бұрын
I solve switch problem by adding 1second relay with 12V ACC
@benjaminalliet4078 Жыл бұрын
When you turn the key ON, the relay close the CAN L itself after 1 second?
@pontesmocho31403 жыл бұрын
Good job.. Can you please tell me if is possible to do the same on my Vivaro 2012 bosch 0281 018 497 Edc17c42 tc1767? Thanks
@CarLabImmoTechnicalChannel3 жыл бұрын
Please use the Solution Finder for Immo Bypass: carlabimmo.com/immo-bypass/finder. If you don’t find the solution that you are looking for in the Immo Bypass database, please make a post on our Official Forum: forum.carlabimmo.com. If you provide enough information about the ECU, car, production year etc., our Expert should be able to develop a solution for you.