Boss BCB-60 Pedalboard Assembly

Now it is possible to use Boss BCB-60 with an effect loop.
You can check scheme on 6:02
Теперь возможно использовать Boss BCB-60 с петлей эффектов.
Посмотреть схему можно на 6:02

[@joeyravage4798]

Tune at the end was badass !

[@N05feratuZ0dd]

Thanks for the diagram at the end. I was recently trying to figure out how to run the B channels on this board. I was running it with just the return and send in my effects loop and then other pedals straight into the amp without the B channels. I also didn't realize you could make room for the expression pedal. I never read the instructions. Great video for this pedalboard. Thank you.

[@metalcat8323]

I'm glad that I could help you🤘🏻

[@Coasterdude02149]

Thank you, after a week and a half of trying to figure out where I was going wrong I got it all figured out thanks to you 🤘🏻 I have a Blues Driver going directly into the amp. Chorus, Delay & Reverb in F/X loop. Was confusing figuring out the send/return on the board but I could do it without the board. Much prefer WITH the board, l keeps everything tidy.

[@metalcat8323]

Nice to hear that you did it well. Keep on rockin 🤘🏻

[@oledodeck]

Thank you for sharing the fx loop logic!

[@metalcat8323]

It's my pleasure ;)

[@PlaneTShakeRo]

I was looking for a fx loop setup with this pedalboard. Thank you for the idea at the end!

[@metalcat8323]

It's nice to hear that. Thank you!

[@OscarGMartinezP]

I'm into it... The think is that I'm using the four cables method with a BOSS NS-2... So, I'm still looking for something that may work with this kind of pedalboards... Any help will be welcome, thanks in advance and thanks for this video and explanation!

[@patrickhoy1347]

@@OscarGMartinezP UPDATE: Thanks to this video showing the FX loop arrangement at 6:08 and also the Roland articles I posted I think I figured out how to set up this BCB-60 pedal board with an NS-2 noise suppressor in 4 Cable mode + an amp with an FX Loop. It's theoretical at this point since I'm waiting for my new amp to arrive so I can't test it yet but based on Metal Cat's arrangement at 6:08 I think it should work. Obviously it would be different for you since you are using different pedals than me but here's what I've worked out so far: Guitar ---> VOX V847 Wah ---> BOSS TU-2 Tuner --> BOSS NS-2 Noise Suppressor (INPUT) ---> Then out from BOSS NS-2 Noise Suppressor (SEND) ---> BOSS OS-2 Overdrive/Distortion ---> BCB-60 Pedal Board RETURN A ---> Then out from BCB-60 Pedal Board RETURN A ---> Guitar Amp INPUT Then: Guitar Amp FX SEND ---> BCB-60 Pedal Board INPUT ---> Then out from BCB-60 SEND ---> BOSS NS-2 Noise Suppressor (RETURN) ---> Then out from BOSS NS-2 Noise Suppressor (OUTPUT) ---> BOSS DD-6 Delay ---> BOSS RV-6 Reverb ---> BCB-60 Pedal Board RETURN B ---> Then out from BCB-60 Pedal Board RETURN B ---> Guitar Amp FX RETURN If you haven't figured out how to set all this up yet with your gear maybe this comment will help. Good luck.

[@mistersternberg2]

This was helpful. Thank you!

[@TravisBrowning-bl1il]

Maaaaan ..... I dig that song brother! Super impressive!

[@dehanramadhan3420]

Awesome!!! 🔥🔥🔥🔥

[@indrajithak47]

That ending track rockin pretty well

[@JuanPabloContrerasC]

The Fiery Furnace - Ethan Meixsell he is the owner of the song ;)

[@indrajithak47]

@@JuanPabloContrerasC appreciate it broda 🙏🤘🏻

[@jesuscruz3836]

GREAT MUSIC

[@reart_guitar8534]

Thanks for the diagram, one question the SEND and RETURN red words goes to the amp?

[@biggjazza6759]

So the expression & 2 drive pedals are before the amp & your delay and eq are in the fx loop? Nice cabling! 👏🏻

[@metalcat8323]

Yes that's right. Thank's :)

[@jeffburmester1390]

I need to try the 4 cable method with my tc electronic plethora and wah pedal.

[@michaelmattson3515]

Ok now I get it with the 4 cable system on this board. What about loop hum from the same power supply?

[@pyratoothNL]

May I ask what you setting you use on the Angry Driver (Charlie, BD, both or parallel)? That thing is so versatile, but you've got an SD running into it too.

[@metalcat8323]

Sorry for the long reply... I mainly used it as a BD. At the moment, this pedal is not in my pedalboard, SD1 is enough for me.

[@koefalba2123]

Can the Boss ME80 fit in that case

[@nizodizo9549]

Looks like an afternoon.

[@richardjones2811]

Has anyone used this with the effects loop and has it worked right?

[@leandroguero586]

Revil desse pedal 😐 quero comprar mas tô em duvida.

[@jemsar2]

I have a couple of questions. 1. Where’s your tuner (pedal)? 2. I am having a problem getting a similar setup with my wah pedal. What did you do to configure this? 3. I can’t seem to find anyone that has new cutout foam so I can work on this again. Do you know where I can buy some?

[@metalcat8323]

1 - At the time of recording the video, I used the PolyTune Clip tuner. I didn't have a pedal back then. 2 - Some pedals have an entry too deep and cannot receive power (for example, early versions of the Julia pedal from Walrus Audio). That's how it was with the wah-wah pedal when I used the original Boss cables. Try to use others or twist them or something. 3 - Sorry, I don't know where to get a new one. If you have them completely spoiled, try using Velcro. Just like regular pedalboards.

[@andym2612]

In Canberra, Australia we have a 2 stores that specialize in the making of a massive range of various rubber products of all shapes and sizes, and even offer a custom cutting service. The retailers are called "Clark's Rubber" and "A.C.T Foam & Rubber". I once bout a similar rubber to the Boss pedal board foam, from Clark's, for a roof rack project I was making for my car. From what I remember it wasn't expensive at all.

[@DunderHead.5000]

I need something for 7 Boss-sized pedals.

[@okachumi8139]

Title of the outro ?

[@metalcat8323]

The Fiery Furnace - Ethan Meixsell

[@natalyabragina4096]

=^____^= супер кот ;-) :-)

[@lennoncarroll6805]

I have a problem, I have everything set up properly but I don’t get any sound through my guitar when I try to use it :(

[@metalcat8323]

Hi, sorry to hear that... Without seeing the connection scheme, I can’t tell what could be the reason. Can you send photos of the connection scheme to my email ([e-mail])? So that I can see the reason for the lack of sound.

[@Adam0Yahya]

Did you turn the power on?

[@SamuraiBud]

but no sound sample

[@emotegisoda]

How's the power supply does it hum?

[@metalcat8323]

I have a different pedalboard now. But as far as I remember, the power supply did not make any hum.

[@UserUser-ef2wt]

That case with the lid open the pedals all fall off. That case is not effective it easily provides accidents.

[@colinjames2469]

no

[@Carlitos198017]

Can you fit a Boss GT3 in there?

[@metalcat8323]

Sorry, I don't have a Boss GT3, so I can't help with that.

[@JamesHux]

How does the board itself get its power supply?

[@metalcat8323]

Via external power supply.

[@jakollee]

@@metalcat8323 I thought the power supply is in the upper left corner, no?

[@awidmusicawidmusic479]

Salut j'ai vie la vidéo mais j'ai besoin de cette valise puis je trouver ce t'apparai. Si oui de quel façon je suis au Mali et puis joue la kora.

[@fattirevsbud]

What Wah are you using? I bought a Cry Baby but the plug won’t work in it.

[@metalcat8323]

On video Dunlop Crybaby Classic. I changed the pedalboard a long time ago so I can't check for sure... Sometimes the power input is too deep (for example, early versions of the Julia pedal from Walrus Audio). I can assume that in your case something similar. Try swapping the wires.

[@V1VISECT6]

i bought a newer crybaby and it has a recessed power jack so the power cable on the daisy chain doesn't fit. I would use a 1 Spot 9V idk how old it is but it works. I swaped my board around today and the power cord on that thing fits it just fine.

[@brunorotella1012]

JajajajajajJJ 🤣🤣😂🤣🤣

[@joemarshlljmp]

too fast and bad music

[@metalcat8323]

I think I agree. At the time of filming the video, everything was in experimental mode.

[@cale583]

junk, waste of money

[@teddunton1931]

Not master lots of changes v