BREATHING EASIER with a JMAX Engineering Snorkel - TOYOTA HILUX N70 INSTALL

[@davidha8148]

Look sick mate. I cracked up so hard when u thought u stuffed up. Installing a snorkel soon.

[@SendinIt]

Haha thanks mate, was stressful for a moment there

[@marcushubka529]

Hey man great video. I'm currently looking Into getting one for my n70 and this has helped. Thanks again!

[@IDontTalkToCops]

I’m about to order one of these for my Hilux LN106. Love the colour combo you went with. I think I might go the same 👍

[@Inboundbogie]

What's with these things??.. sorry RAM Air SAFARI snorkels the whole way. Never understood the whole facing backwards concept thing.

[@flacky93]

Awesome stuff mate 😃 i should've went a stainno but ended up going the mighty faithful safari snorkel 🤙🏽👌🏽👌🏽 always nervous when u chop a big hole in u quater guard 🤣🤣 luckily u did an awesome job

[@SendinIt]

Very scary job I tell ya that much! Haha. I was going to get safari initially but 3 years later I ended up with this truck stack hah

[@flacky93]

🤣🤣 hahahahaa awesome stuff mate 👌🏽👌🏽

[@MarinePredators84]

Would of been nice to hear it.. looks the part. Nice one mate

[@SendinIt]

kzbin.info/www/bejne/sKLJnZqrndGIl8U First 10seconds of this clip has the snorkel sound mate. Thanks for watching 😀

[@joshnowland317]

If you remove a snorkel do u have to make changes to the air box inlet say block it off or just leave it open?

[@russellking9762]

No way…i’d cry making that ditch in my rig…i’ll get the Safari instead…no disrespect bro!

[@Jimmy_Saf]

Should have put the flex pipe on the snorkel first not the air box

[@themechanicslab]

Hey mate, can I ask your feedback on the J-Max snorkel after a years usage. I first watched this vid close to when you uploaded it and wanted to see what your thoughts and feed back are now after using it and putting it thorugh its paces. Also, could you use a silicone right angle or 45 in lieu of the wire reinforced hosing. Not a fan of that which to me representds the biggest weakpoint of the whole system and for close to a $G I'm not fully sold just yet. Cheers bro, appreciate the feedback and love the channel

[@SendinIt]

Yeah great question mate, the snorkel is solid as ever in its mounts after doing 20000km on and offroad last year. It does not cause water to pool in the air box when driving in heavy rain. And as for the flexibile pipe, yes it could be peiced i suppose but when yoh push the excess back into the gaurd it is quite compressed meaning theres more steel support to stop it caving in from induction. But like you said silicone pipes would be ideal. Although i would use a custom air box for that install. Because the factory box setup is very tight to connect the pipework. Thanks for watching our channel mate 😀

[@connormccreesh4007]

3:35 "its a bit of a bastard of a spot", did you consider taking the plastic guard from behind the wheel flare off?

[@SendinIt]

Definitely next time. Plus get help from a mate

[@smatt9993]

What about the induction sound on long drives? Annoying? like a sports exhaust on a 6 cylinder commodore.

[@SendinIt]

The noise is mainly present in 2nd, 3rd gear. At 100kmh there's no apparent noise. Window up and it's not noticeable in the lower gears

[@maxday1484]

nice mate well done

[@np2117]

Is that stepped section on the base of the snorkel where you attach the flexi pipe 4 inches wide or is it reduced to a 3 inch there? Great video 👏🏻

[@SendinIt]

Correct, unless your getting the custom airbox. It 4 down to 3 to fit the existing factory box

[@jarrodsmith999]

What’s the sticker colour?

[@SendinIt]

Its the dark grey reflective, can only be seen in certain light conditions (artificial light)

[@omerh6320]

hello, do you encounter a problem such as wetting the air filter, does water go to the air box in heavy rain?

[@SendinIt]

Never a single drop 👍

[@reesy22]

Looks mint bro. What lift tyre size and offset were you running here?

[@SendinIt]

2 inch lift, and tyres are 32inch. Just don't remember offset on the rims.. got them second hand 🤔

[@darrenmarney7893]

What winch bumper is that it looks very nice

[@SendinIt]

ARB Deluxe combination bar mate 👍🏼

[@suhailpador650]

Check out rhino evolution bumpers

[@jyettstarz]

Definitely a roofer

[@tonycook2347]

great vid, did it do anything to your fuel economy?

[@SendinIt]

I believe it has made a difference, but I put more parts on the ute so now its basicly back to were it was before

[@naturallyaspirated752]

Mate, can you give the detail of ur snorkel. The colour is it matte black??

[@SendinIt]

Gloss black ⚫

[@psy06]

that hose that comes with snorkel is pure shit. soon or later all you'll have is that wire that runs through it

[@SendinIt]

Time will tell i guess, be interesting to see how long i get out of it

[@smatt9993]

If you look closely can you see panel waves along where you've cut with the snips. Does the pinch weld hide it? As anal as I was cutting mine with snips you can still see warping. Having a black car doesn't help.

[@SendinIt]

Yes definitely a very slight wave. But the pinch weld is more than big enough to cover that up. I found the cut out a little to sloppy and i would cut 2-4mm inside the black line next time

[@smatt9993]

See I got mine from PHATBARS as I wanted the short entry. The pinch weld they supply is much thinner so way less room for error, plus you have to remove 3 panel bolts to beable to bend the top of the fender out so you can manipulate the base of the snorkel through. Just to much bending and manipulating around a skin panel for my liking. The risk for damage is to high. The thing is you only get 1 shot and now I'm regretting even attempting it 🥴

[@SendinIt]

@@smatt9993 I thought mine was going to be short entry but it didn't end up that way. (Jmax didn't have photos of a low cut). That sounds tricky as compared to these snorkels

[@smatt9993]

@@SendinIt cheers for a bit of insite to yours. Been watching heap of videos and searching loads of images to see whether wrinkling is normal to help put my mind at ease. Should have just gone s safari haha.

[@caseymelbourne9233]

Definitely get your own pinchweld the one they supply is thin and cheap it’s wavey and the steel insert overlaps

[@tysondonohoe505]

Can anyone tell me if these or any stainless snorkel can be used as a swap/upgrade on tjm airtec pvc ? Or am I getting a new quarter panel as well lol

[@SendinIt]

I'd ask Jmax. They do safari swaps all the time mate.

[@williamnicholson6776]

I've got one on my luxy diftent brand , how do ya all find the horrible.intake noise ? I'm about to rip off and put a plastic one back on any 1 been able.to make it quieter??

[@SendinIt]

I dont mind the noise tbh. Tryes are louder at the moment haha

[@carlosvo312]

Hi nice video but working with heavy rain ?

[@SendinIt]

Drove around 6 hours straight in rain across the Nullarbor recently and no issues with water in the air filter housing. Ensure the duck lip rubber valve is functioning and clear to allow any excess water to leave the housing when the engines off

[@carlosvo312]

Sendin' It the duck lip rubber valve is original of the filter box system? Or the snorkel ?

[@SendinIt]

Yes correct its the original valve on the box

[@suhailpador650]

Is that a low cut or standard? Is it gloss black ?

[@SendinIt]

Low cut in gloss black mate 👍

[@Foufouvideos]

Shiping to Europe/Luxembourg possible?

[@SendinIt]

Best to ask the manufacturer directly but i think that would be possible

[@Foufouvideos]

Sendin' It thank you Mister

[@danielayris3623]

They look good but that's a huge hole in the car?

[@SendinIt]

Yeah but you will have permanent fixing or holes in any snorkel install i suppose

[@Asherah55]

Brother I got an N80 Hilux.. I'm torn between Stainless or Safari people are saying that the Stainless Snorkel gets water through to the airbox? How do you find it so far?

[@SendinIt]

Havent found water entry to be a issue at all. Drove 10 hours in rain across the Nullarbor and it didnt fill my airbox up. Just ensure your duxk lip valve is working at the base of your airbox

[@Asherah55]

@@SendinIt oh man.. want it so bad but scared AF!

[@joshstirling4605]

Hey man, is that the standard snorkel or the lowcut? Cheers

[@SendinIt]

That is the low cut version mate, they don't have many images online of these

[@joshstirling4605]

Sendin' It cheers mate, looks sick, looking at getting one for my own 🙂

[@SendinIt]

@@joshstirling4605 Definitely worth the extra money over a plastic. Looks factor anyway

[@joshstirling4605]

Sendin' It yah always been my issue with the safaris etc, look cheap asf compared to the stainless ones

[@caseymelbourne9233]

Get your own pinch weld the one Jmax send you is trash

[@Renegade040]

OMG, don't like that install at all. Such a large cut in the fender would weaken it, defending prefer the unit I got. Also why is the head facing away from the airflow?

[@SendinIt]

The fender doesn't exactly hold the car together, I prefer the snorkel being recessed into the gaurd each to there own i guess

[@4wdaddict41]

What lights are those in the front of your weapon ?

[@SendinIt]

They are the mighty cheap Kings 9inch spotlights mate

[@mohamedalihebboul2214]

Nice snorkel, but the cut is too big...

[@SendinIt]

1/4 of the panel is missing now haha 👍

[@ScootTV]

Still got template

[@SendinIt]

Shes long gone 🙃

[@daniellopes6131]

Sou do Brasil.. queria comprar um desse como eu faço..

[@SendinIt]

Eles estão disponíveis no Brasil?

[@daniellopes6131]

@@SendinIt eu não sei... vc tem Whatsapp.? Meu é 55 43999113088

[@SendinIt]

@@daniellopes6131No WhatsApp sorry

[@daniellopes6131]

Quanto custa um desse ai ?

[@SendinIt]

@@daniellopes6131 $1100 AUD

[@goldrushau8425]

Dude! Backwards facing? Do you know anything about physics ? Hahaha

[@SendinIt]

No I don't 😆

[@jellybaby9630]

Noisy in ya ear????

[@SendinIt]

Little bit of noise but i kinda like the sound :)