Briggs and Stratton 3.5HP Horizontal Linkage

  Рет қаралды 168,883

Real Man Skills

Real Man Skills

Күн бұрын

4strokerebuild....

Пікірлер: 210
@gspfunk
@gspfunk 3 жыл бұрын
Thank you!! We’ve had our edger for at least 15 years, and I didn’t pay enough attention to the springs and where they went. After looking at a ton of incorrect diagrams and videos, I finally came across yours with the exact same setup. The small spring that was missing in your video was incorrectly connected on ours, and your video helped us get it sorted. Thanks again!!!
@RealManSkills
@RealManSkills 3 жыл бұрын
Happy to help! Thanks for watching!
@dagrote1
@dagrote1 3 жыл бұрын
This video just saved me! Someone handed me a disassembled 091202 in a box, and several of the linkages were missing. I'd still be scatching my head if you hadn't posted such a detailed descriptions with the parts numbers of the linkage to the wind vain governor. Thanks a million.
@RealManSkills
@RealManSkills 3 жыл бұрын
Happy to help! Thanks for watching!
@williamwixon
@williamwixon 7 ай бұрын
Thank you your video saved me too even though my engine isn’t exactly the same as yours. It was enough information to get the tiny spring in the right spot. Mine has a very thin, aluminum air vane and the tab where the wire goes through was bent 90° from the way it should be. With your video I was able to get the spring in the right spot and bend that tab back. I would’ve been completely screwed without your video. Thank you so much.
@RealManSkills
@RealManSkills 7 ай бұрын
Happy to help! Thanks for watching!
@donaldelder540
@donaldelder540 2 жыл бұрын
Thank you, you have stopped me from going crazy
@RealManSkills
@RealManSkills 2 жыл бұрын
Happy to help! Thanks for watching!
@gustavoverdusco6275
@gustavoverdusco6275 4 жыл бұрын
excellent video has helped me a lot I bought a small tiller machine and they told me that I just needed to clean the carburetor and after finishing I noticed that something was wrong and this video helped me solve it
@RealManSkills
@RealManSkills 4 жыл бұрын
Happy to help! Thanks for watching!
@BigDDaavvee
@BigDDaavvee Жыл бұрын
Brilliant it helped me out big time, I’d just bought a tiller with a briggs and Stratton 3.5hp engine on it and it looked and worked great. But on the way home it took a tumble in my truck when a stupid deer decided to cross the road to stare at my headlights, so thanks for your time and effort in making this video for people like me.
@RealManSkills
@RealManSkills Жыл бұрын
Thank you for watching!
@davidschwartz5127
@davidschwartz5127 8 жыл бұрын
Thanks, now in my seventies, couldn't remember how the springs connected up even though I just took it apart. Thank god for You Tube!
@RealManSkills
@RealManSkills 8 жыл бұрын
Thanks for watching!
@petepeabody8905
@petepeabody8905 3 ай бұрын
So simple, but so necessary too. Thank you
@RealManSkills
@RealManSkills 3 ай бұрын
Thanks for watching!
@flashgordon6238
@flashgordon6238 8 жыл бұрын
Just what I needed to confirm my setup after the carb rebuild. I had taken pictures of the linkages with my phone, but the phone was stolen before the rebuild was done!
@RealManSkills
@RealManSkills 8 жыл бұрын
Thank you for watching! Happy to help!
@carlospadilla9822
@carlospadilla9822 5 жыл бұрын
Can you show how the throttle cable is hooked up please and what is the little plastic piece right next to where the top of the z cable goes
@armandm4587
@armandm4587 3 жыл бұрын
I just wish to let you know that this video has been so helpful! Thank you so much!
@RealManSkills
@RealManSkills 2 жыл бұрын
You are so welcome!
@slim3840
@slim3840 3 жыл бұрын
Thanks brother. I have the same engine on a Mclane reel mower and needed help with governor spring location. Great video.
@RealManSkills
@RealManSkills 2 жыл бұрын
Glad it helped
@Brianmlife
@Brianmlife 5 жыл бұрын
Thank you, my 3.5 is similar to this, it just has the choke on the control. . This will help get me with re assembling the linkage. for the governor. Knew I was missing something simple.
@RealManSkills
@RealManSkills 5 жыл бұрын
You're welcome and thank you for watching.
@toniannetrincia2939
@toniannetrincia2939 7 жыл бұрын
Thank you, great help since my husband didn't take a picture of the linkage before he ripped the carb apart.
@RealManSkills
@RealManSkills 7 жыл бұрын
Been there, done that! Thanks for watching!
@richags328
@richags328 6 жыл бұрын
Exactly what I needed to see...thank you very much
@RealManSkills
@RealManSkills 6 жыл бұрын
You are very welcome and thank you for watching.
@abelcerrillo2162
@abelcerrillo2162 5 жыл бұрын
Good video....im saving this one an coming back to it when my carburetor comes in.
@RealManSkills
@RealManSkills 5 жыл бұрын
Thanks for watching!
@Mr334cobra
@Mr334cobra 6 жыл бұрын
thank you thank you! loved that you provide part numbers as well!
@RealManSkills
@RealManSkills 6 жыл бұрын
Thank you for watching!
@Mr334cobra
@Mr334cobra 6 жыл бұрын
I bought one of the parts you mentioned thanks to sharing the part number!
@cusoonmyfriend3738
@cusoonmyfriend3738 4 ай бұрын
hello, i have three 3,5 hp briggs (1 on a rototiller and 2 x scarifier) but i dont have this piece 01:53 , looks like theres no link air vane , is it normal ? i dont have the big plastic part that is moving
@pajipower1
@pajipower1 7 ай бұрын
For some reason my stop run lever keeps returning to the stop position while the engine is running. I have everything hooked up as the video. Can someone please advise me accordingly.
@bodeine454
@bodeine454 4 ай бұрын
On our McClane edger there's a throttle cable hooked to one of the holes in that throttle lever and the throttle is controlled up by the hand grips. It keeps the throttle in the same position until you change it. Just get a universal throttle control lever with cable and go that route or there might be a way to tighten the small factory throttle lever down by the engine but I'm not sure how you would go about it.
@abelcerrillo2162
@abelcerrillo2162 5 күн бұрын
Thank u sir.... I replaced the carb on mine an once I turn it on it stays running on super high RPMs, can't get it to run smoothly so I turn it off....I hope I just have a missing governor spring.
@RealManSkills
@RealManSkills 5 күн бұрын
@@abelcerrillo2162 I'm sure that you'll figure it out. Thanks for watching.
@markbrooks770
@markbrooks770 2 жыл бұрын
thanks for that you have solved my problem what is the first spring you showed called. the one connected to the wrong side
@RealManSkills
@RealManSkills 2 жыл бұрын
I have been searching around for an answer to your question. However, that spring seems to be discontinued. Might have to find a suitable replacement from the hardware store. Thanks for watching.
@matthewbonham4859
@matthewbonham4859 6 жыл бұрын
Thank you sir for the informative video instructions. I ordered the correct springs today from amazon. How do I connect the throttle lever cable to carburetor assembly?. I missing something. I have the engine set up as in the video.
@RealManSkills
@RealManSkills 6 жыл бұрын
Throttle cable connections vary with the type of machine the engines are mounted on. Sorry but I don't have that engine any longer and I can't really describe it. Thanks for watching.
@lincbond442
@lincbond442 3 жыл бұрын
Great video! I have the exact same engine and calling out those part numbers was really helpful. Thanks!
@RealManSkills
@RealManSkills 3 жыл бұрын
Happy to help! Thanks for watching!
@lincbond442
@lincbond442 3 жыл бұрын
@@RealManSkills Thank you for your quick reply. I have a question about the brass carburetor adjustment screw located below the choke linkage. The one on my carburetor is very loose and turns with the vibration of the engine. I have been using tape for the time being to keep it from moving. Any suggestions on how I can remedy this problem? Thanks!
@RealManSkills
@RealManSkills 3 жыл бұрын
@@lincbond442 I don't know any "for sure" answer to that problem. Maybe a dab of BLUE loc-tite?
@lincbond442
@lincbond442 3 жыл бұрын
@@RealManSkills Thanks for your reply. I was thinking along the same lines but I just need to make sure the loc-tite doesn't get in too deep and clog up the system.
@jerrydavis676
@jerrydavis676 Жыл бұрын
Just what I was lookin for! Awesome video!
@RealManSkills
@RealManSkills Жыл бұрын
Thanks for watching!
@michaelsinclair2880
@michaelsinclair2880 2 жыл бұрын
How do you take a water pump off the 5hp Briggs and Stratton it is on the shaft and I don't know how to get it off
@RealManSkills
@RealManSkills 2 жыл бұрын
They can be difficult sometimes. Sometimes there is a set screw on the pump that presses on the shaft. You will need to remove the set screw. Other times, it's just rusted on. Here is a video to a pressure washer pump that I had to remove - there is a set screw on this unit - kzbin.info/www/bejne/nnWlaH2ffJ1oa7M
@fizban7
@fizban7 2 жыл бұрын
OMG I was looking for this exact diagram. I was using a troy bilt tiller, with a Briggs & Stratton 094212-0205-E1. I took the spring out to replace gaskets and had no idea how to put it back together. Take photos people! Thank you!
@RealManSkills
@RealManSkills 2 жыл бұрын
Happy to help! Thanks for watching!
@seanmehmood790
@seanmehmood790 5 жыл бұрын
Just what I needed to know to tear apart my carb. Thx
@RealManSkills
@RealManSkills 5 жыл бұрын
Thanks for watching! Happy to help.
@Michigan381
@Michigan381 3 жыл бұрын
I know this video is old but I got two questions, I got one of these engines from my cousin and he was not sure what it went to, what do they go to and the other weekend I got one fully rebuilt for $30 would one be any good for a go kart/ bumper kart? (In terms of slow/good on gas?)
@RealManSkills
@RealManSkills 3 жыл бұрын
I don't know about a go kart, but this was a very popular engine on a smaller Mini bike.
@derwoodsomething3988
@derwoodsomething3988 4 жыл бұрын
Thanks for the help. This is my first time commenting on video. (Sorry if this method is wrong.) While working on my simular engine the air vane tab broke. Cannot seam to find my style air vane. The one on my engine is metal (old) your video show pastic (newer concept). Could you please provide me with air vane part number or direction to find it myself. Stay safe and have a blessed day, de
@RealManSkills
@RealManSkills 4 жыл бұрын
It would help to know your model number. I use www.partstree.com to identify parts. Thanks for watching.
@ronnyracer1175
@ronnyracer1175 5 жыл бұрын
Great video, helped immensely! many thanks!
@RealManSkills
@RealManSkills 5 жыл бұрын
And thank you for watching!
@bluesbiker5480
@bluesbiker5480 8 жыл бұрын
Can you please specify the part-number of another spring, which you already have?
@RealManSkills
@RealManSkills 8 жыл бұрын
The spring that is already on the engine, I believe is Briggs and Stratton part #691289. Hope that helps. Thanks for watching.
@marioaguilar3453
@marioaguilar3453 2 жыл бұрын
Thanks you so much for instructions 5⭐️⭐️⭐️⭐️⭐️
@RealManSkills
@RealManSkills 2 жыл бұрын
Thanks for watching!
@Waco-Silos
@Waco-Silos 3 жыл бұрын
Thanks, mine was also missing the spring.
@RealManSkills
@RealManSkills 3 жыл бұрын
Thanks for watching!
@nightmareinaction629
@nightmareinaction629 7 жыл бұрын
I got one of this from a friend I went with him to the lawnmower shop to get the carburetor uncloged but when we got it back because he was charging 350 dollars for the repair thee carburetor was completely taken apart and lots of parts were missing do you know any alternative carburetors
@RealManSkills
@RealManSkills 7 жыл бұрын
No alternative carbs that I know of. Sorry
@nightmareinaction629
@nightmareinaction629 7 жыл бұрын
sblg43 well I quesst I have to look around engine runs fine on propane but it's a hassle to get started with propane sometimes thanks for the reply
@johnlibonati7807
@johnlibonati7807 5 жыл бұрын
I know this is old, but you can buy new carbs on eBay or Amazon for less than $20. I just discovered this while looking for the rebuild kit.
@chadriggs3322
@chadriggs3322 7 жыл бұрын
i have an engine just like this one. it only goes one speed but i would like to modify it so that i would be able to adjust the throttle like on older models. Do you think thats possible?
@RealManSkills
@RealManSkills 7 жыл бұрын
There may be other throttle controls available. Different machines (rototillers, mowers etc..) have different throttle controls but use the same engine. Can't say for sure but I bet you could find a different control to put on your engine.
@chadriggs3322
@chadriggs3322 7 жыл бұрын
i have an older 3.5 briggs on my other edger that has the throttle control below the choke. on that one you can control the throttle. its a very similar setup. i may just need a few extra parts to do it on my other edger. Thanks for your response.
@pascalmasclaux2177
@pascalmasclaux2177 8 жыл бұрын
Thank you for your reply
@annmariesalas2677
@annmariesalas2677 3 жыл бұрын
What about the choke?
@RealManSkills
@RealManSkills 3 жыл бұрын
1:18
@pascalmasclaux2177
@pascalmasclaux2177 8 жыл бұрын
Hello Thanks a lot for the video. I need to change the gaskets and the diaphragm of my concrete machine which have a Briggs&Stratton 3,5 Hp Horizontal Linkage modele:91232 Type:1363 E1 Code:980513FA.Do you know the numbers for the gaskets diaphragm kit
@riley7796
@riley7796 7 жыл бұрын
Hi i have the same engine you have in this video, and could you tell me if it is normal if it is relatively easy to pull start?
@RealManSkills
@RealManSkills 7 жыл бұрын
Normally, yes.
@midgyrich
@midgyrich 7 жыл бұрын
Riley Pilot As long as you feel resistance, I think you're fine ;)
@Gazlovestacey
@Gazlovestacey 5 жыл бұрын
Nice video. Is this a 2 or 4 stroke motor? Thanks
@RealManSkills
@RealManSkills 5 жыл бұрын
4 stroke
@flip2k814
@flip2k814 8 жыл бұрын
Thanks so much for all the help! Do you by chance know the number for the other spring on the anchor? I damaged it and was hoping you may know since I can't find the number diagram. Thanks
@RealManSkills
@RealManSkills 8 жыл бұрын
The spring that is already on the engine, I believe is Briggs and Stratton part #691289. Hope that helps. Thanks for watching.
@wesleyantinetti4427
@wesleyantinetti4427 4 жыл бұрын
Thank you
@RealManSkills
@RealManSkills 4 жыл бұрын
And thank you for watching!
@marycgarmon7140
@marycgarmon7140 4 жыл бұрын
Thank you. I think I can fix mine now
@RealManSkills
@RealManSkills 4 жыл бұрын
Thanks for watching!
@mateuszkosmal646
@mateuszkosmal646 9 ай бұрын
How model engine?
@RealManSkills
@RealManSkills 9 ай бұрын
As mentioned 25 seconds into the video, it is model 091202-1249-E1
@cusoonmyfriend3738
@cusoonmyfriend3738 2 жыл бұрын
subbed of course and thanks a lot for helping in a world where almost everyone is a pile of shit asking for money at each tip
@RealManSkills
@RealManSkills 2 жыл бұрын
Thanks for watching!
@thierryfranc8832
@thierryfranc8832 7 жыл бұрын
great ! perfect video
@RealManSkills
@RealManSkills 7 жыл бұрын
Thank you and thanks for watching!
@ethynvota1956
@ethynvota1956 5 жыл бұрын
Why u steal carsandcameras intro?
@RealManSkills
@RealManSkills 5 жыл бұрын
That engine starting in my intro is my own lawn mower starting. Nothing stolen here.
@ethynvota1956
@ethynvota1956 5 жыл бұрын
@@RealManSkills i know, it was a joke. And it is a good intro
@joemoore2696
@joemoore2696 5 жыл бұрын
I have searching for almost a year trying to find a picture or diagram of how these linkages should be setup. Thank you so very much!! You just saved me the money of going out and buying a new rototiller for the garden!!
@RealManSkills
@RealManSkills 5 жыл бұрын
Happy to help and thanks for watching!
@Ueddyyytube
@Ueddyyytube 7 ай бұрын
I have the same problem, the linkage was installed incorrectly the same way you explained Thanks
@RealManSkills
@RealManSkills 7 ай бұрын
Happy to help
@carloscervantes2706
@carloscervantes2706 7 жыл бұрын
Thank you so much for the help I've been trying to figure out what was missing on my engine. Keep up the good work by the way.
@RealManSkills
@RealManSkills 7 жыл бұрын
Happy to help. Thanks for watching!
@dr.crentist3155
@dr.crentist3155 6 жыл бұрын
Informative video, thanks. I have same engine on my lawn edger. It runs and starts great, shuts off etc. My issue is the throttle speed lever. As engine vibrates the lever moves from high to middle. I have to continuously push it up to complete lawn edge. I took it apart, and saw only 1 spring and assumed i was missing one. Your video shows only one also so i guess mine is correct. Any ideas on tightening that or to get lever to stay high? Its not a bolt, sort of a rivet. Nothing to tighten Thanks
@RealManSkills
@RealManSkills 6 жыл бұрын
Can't say for sure, but you might try to bend the lever so it doesn't move so easily. Hope you figure it out. Thanks for watching.
@dr.crentist3155
@dr.crentist3155 6 жыл бұрын
sblg43 Thanks for replying so fast and supplying the video.
@benvanh4223
@benvanh4223 3 жыл бұрын
I have a similar engine 91202 0016 01 95031703 and linkages are slightly different. Any diagram you know of to make sure it's all hooked up correctly? Thanks
@keithburge4608
@keithburge4608 3 ай бұрын
Does anyone know the part number for the governor blade?
@johnridings3291
@johnridings3291 12 күн бұрын
Your video is my go to reference whenever I take apart my Briggs & Stratton carb. Thank you for taking the time to put out this excellent video. You da man!
@RealManSkills
@RealManSkills 11 күн бұрын
And thank you for watching!
@сибирякСФО-щ7в
@сибирякСФО-щ7в 15 күн бұрын
Живу в России, у меня такой двигатель стоит на культиваторе , к сожалению ни где не найти родные пружины и тягу карбюратора
@RealManSkills
@RealManSkills 15 күн бұрын
That's unfortunate. I hope that you find something. Thank you for watching.
@paulbloomer
@paulbloomer 6 жыл бұрын
Thanks for sharing! I was able to correct the mess on a used tiller I purchased. Works perfectly now.
@RealManSkills
@RealManSkills 6 жыл бұрын
Happy that you figured it out. Nothing better than a well running machine to get things done! Thanks for watching.
@kevinaburt2918
@kevinaburt2918 2 жыл бұрын
I have it, leave me alone.💯
@trandall8
@trandall8 5 жыл бұрын
Nice video, clearly shows linkage parts except the actual throttle cable connection which is my issue. I can clearly see the throttle cable connection and function however, I think it's slipping making my mower power inefficient. I can't quite tell if the very tip of the cable broke or if the 'z' bend is not sufficient or if the plastic piece where the cable is inserted has word too much. Seems the cable, at maximum power slides through the connection versus moving connection to full open. Any thoughts or can you show the throttle cable connection? Thanks!
@keithratcliffe3284
@keithratcliffe3284 Жыл бұрын
Do you have a video about the rebuild of this particular engine?
@RealManSkills
@RealManSkills Жыл бұрын
Sorry, I do not. However, the 5HP engine video series is nearly identical except for the carburetor linkage.
@johnridings3291
@johnridings3291 6 ай бұрын
Thanks for the informative video! 👍
@RealManSkills
@RealManSkills 6 ай бұрын
Happy to help!
@jjhdtec
@jjhdtec 2 жыл бұрын
I have same model motor, where can I find the parts ?
@RealManSkills
@RealManSkills 2 жыл бұрын
All over the internet. I like to visit www.partstree.com
@jesussalinas7776
@jesussalinas7776 3 жыл бұрын
Wonder if you could put a mukuni style carb
@RealManSkills
@RealManSkills 3 жыл бұрын
I never tried.
@bobbiwilson7624
@bobbiwilson7624 8 жыл бұрын
Thanks a lot for the video...I did not take a "before" photo of the linkage and had mine all screwed up. Briggs website was not helpful and you saved the day..
@RealManSkills
@RealManSkills 8 жыл бұрын
+Roger Wilson Happy to help. Thank you for watching!
@seannot-telling9806
@seannot-telling9806 8 жыл бұрын
I too must say Thank You for the same reason. Thank You!
@RealManSkills
@RealManSkills 8 жыл бұрын
Sean Not-telling and Thank you too!
@jw2par
@jw2par 2 жыл бұрын
I have the same engine . I replaced the head gasket , what should the bolts be torque to ?
@RealManSkills
@RealManSkills 2 жыл бұрын
Cylinder head bolts should be torqued to 140 INCH pounds. ***NOT FOOT POUNDS***. Thanks for watching.
@jw2par
@jw2par 2 жыл бұрын
@@RealManSkills so about 12 foot pounds? Thanks I broke 2 bolts thinking it was foot pounds . Glad they came out easy .
@craighagedorn4842
@craighagedorn4842 Жыл бұрын
Super helpful thanks 👍
@RealManSkills
@RealManSkills Жыл бұрын
Thanks for watching!
@jeffclark9500
@jeffclark9500 5 жыл бұрын
Thanks for the video. I have two of these and they both have the same problem as your.
@RealManSkills
@RealManSkills 5 жыл бұрын
Happy to help. Thanks for watching!
@wainwright2868
@wainwright2868 Жыл бұрын
Best 5 minutes video ever
@RealManSkills
@RealManSkills Жыл бұрын
Thanks for watching!
@ricardocabello6386
@ricardocabello6386 5 жыл бұрын
Hello, I have a question, i'm working on a McLane edger 3.5hp. I'm trying to remove the carburetor from fuel tank. I see a locating pin that keeps the carburetor from turning to remove, i'm assuming its a manufacturing thing. how do I go about removing this pin? I see videos where the carburetor is just lifted out, not on mine. thanks for your time and have a great safe day. Richard
@gomher9145
@gomher9145 5 жыл бұрын
Look for one more screw under throttle lever
@TaserTot
@TaserTot 2 жыл бұрын
I have a 94202 3.75hp on a tiller. Not sure if it's the same part number but now I can at least see how it's supposed to hook together. Someone had the small spring going directly to the throttle butterfly. My governor is a bit different also. It's a small plastic tab with a hole in it under the cover. 👍
@RealManSkills
@RealManSkills 2 жыл бұрын
Thanks for watching!
@jamesbubnick
@jamesbubnick 4 жыл бұрын
Awesome video, helped me to remember how to set up my linkages. Thanks for the information.
@RealManSkills
@RealManSkills 4 жыл бұрын
Happy to help! Thanks for watching!
@chriscannata8044
@chriscannata8044 5 жыл бұрын
Thanks man... got a lot of photos and then somehow deleted them and was screwed!!!!! Been all over the net looking at diagrams and it's like a secret sauce recipe to get this figured out.
@RealManSkills
@RealManSkills 5 жыл бұрын
Been there too. That's why I made the video! Thanks for watching!
@primerpodcast8557
@primerpodcast8557 6 жыл бұрын
thanks for making this simple video. good to know my lawn mower repairman had linkage spring in wrong place.
@RealManSkills
@RealManSkills 6 жыл бұрын
Thanks for watching! Happy to help!
@jamesphillips9750
@jamesphillips9750 6 жыл бұрын
I have that same engine on a Craftsman lawn striper reel mower.It has always ran rich since new.Can you tell me if the brass jet screw is supposed to be seated or turned out to adjust,thanks
@RealManSkills
@RealManSkills 6 жыл бұрын
This particular engine has a non-adjustable carburetor. Without seeing yours, I can't be certain.
@willway9378
@willway9378 3 жыл бұрын
Thanks! I have one almost exactly like it. It is very helpful in reassembly to have your video. I was just at the point of cleaning the carb and replacing the fuel pump.
@RealManSkills
@RealManSkills 3 жыл бұрын
Happy to help! Thanks for watching!
@SnowCamo45
@SnowCamo45 3 жыл бұрын
Got a bud who just got a MC reel. Carb was missing the springs you listed. Thanks 💯💯💯🍻
@RealManSkills
@RealManSkills 2 жыл бұрын
Glad I could help
@destrylazenby2341
@destrylazenby2341 4 жыл бұрын
With your setup it looks like you’re idle is wide open. Shouldn’t the idle screw be touching the block?
@RealManSkills
@RealManSkills 4 жыл бұрын
This video was about showing the linkage. I am sure that I got it running and back to the owner working just fine. This was five years ago, I can't say that I remember much about what else I had to do to tune the carb. Thanks for watching.
@weschaffin
@weschaffin 10 ай бұрын
Extremely helpful regarding the linkage. Well done. This helped me tonight.
@RealManSkills
@RealManSkills 10 ай бұрын
Happy to help!
@matthodgson6414
@matthodgson6414 6 жыл бұрын
Great video. Recently brought a mower with this engine, had a loss of power. Noticed the governor spring is setup incorrect, wrong way around and using the wrong hole. Cheers.
@RealManSkills
@RealManSkills 6 жыл бұрын
Happy to help. Thanks for watching.
@fuji8410
@fuji8410 Жыл бұрын
Exactly what I needed to know and with parts number too! You where a big help! Ty.
@RealManSkills
@RealManSkills Жыл бұрын
Thanks for watching! Happy to help!
@johnstrange6799
@johnstrange6799 9 жыл бұрын
Glad to see this style of linkage. Thanks
@RealManSkills
@RealManSkills 9 жыл бұрын
Thanks for watching. As small engines come through my shop, I hope to share all the linkages that I can.
@johnstrange6799
@johnstrange6799 9 жыл бұрын
Great! It's really really helpful sometimes. I know one of your other linkages helped me before, and this one was great to see as well. I have a 5hp version that I haven't gotten around to playing with yet, but really had no idea on it's linkage set-up. :)
@Hahehhwgajshah72726..
@Hahehhwgajshah72726.. 3 жыл бұрын
Greetings from Sydney Australia.Well done sir.Thanks so much.
@RealManSkills
@RealManSkills 3 жыл бұрын
Happy to help! Hope all is well down-under!
@АлексейОсинин-о8ш
@АлексейОсинин-о8ш Жыл бұрын
Recently I brought nearly the same engine (091212) for restoration with non-standard one end detached spring. Now I know what and how to install properly. Greetings from Russia!
@RealManSkills
@RealManSkills Жыл бұрын
Thanks for watching!
@сибирякСФО-щ7в
@сибирякСФО-щ7в 4 күн бұрын
Доброго времени суток, у меня такой же двигатель 091212 на викинге, если есть возможность подскажите пожалуйста длину тяги которая идёт от карбюратора к воздушной лопасти, пересмотрел все сайты не могу найти родные пружины и тягу, мои растерял работник в мастерской, спасибо
@elvinjhillsr4430
@elvinjhillsr4430 7 жыл бұрын
Hi I would like to know how to take the gas tank off I have one just like that and I can't get the tank off
@RealManSkills
@RealManSkills 7 жыл бұрын
There is a bolt under the tank that needs to be removed. Also, the two bolts holding the carburetor to the engine need to be removed. Since the carb is mounted to the tank, they usually come off together. Hope that helps. Thanks for watching.
@naterowland8520
@naterowland8520 6 жыл бұрын
thank you! Super helpful amen! happy 4th of July. Community rules! USA
@RealManSkills
@RealManSkills 6 жыл бұрын
Happy to help! Thanks for watching.
@hotdawg9840
@hotdawg9840 4 жыл бұрын
Wats the part# or how do i find the entire throttle and linkage kit for this engine? Thanks if u can inform me
@RealManSkills
@RealManSkills 4 жыл бұрын
There is no "entire" kit for this engine. You will have to buy the parts individually. I include the parts numbers in the video. You can also do an internet search for the engine model number (also in the video) and you will find a lot of results for parts.
@hotdawg9840
@hotdawg9840 4 жыл бұрын
@@RealManSkills man my engine has the exact same sset up. Except not entirely. I would lile this set up. But mine was hand operated where your choke and throttle are and down below it had another setup. Long story short. Mine is diff but exactly the same. I want the set up on this with the throt&choke switches being able to have the line directly in them thete instead pf below the feul tank. I appreciate the input and thank u man. I figured but i had to ask. I work onbigger engines. Take care
@douganniewall3429
@douganniewall3429 5 жыл бұрын
Thanks! Just what I needed! Even complete with part numbers.
@RealManSkills
@RealManSkills 5 жыл бұрын
Always happy to help out! Thanks for watching.
@mikeramsay5000
@mikeramsay5000 8 жыл бұрын
Awesome. Thanks for also including part numbers; this is exactly the type of info I need to get my woodchipper back up and running.
@RealManSkills
@RealManSkills 8 жыл бұрын
Thanks for watching! Hope you get it going!
@ericgutierrez8028
@ericgutierrez8028 2 жыл бұрын
I know this is an old video but what did this go on? I just purchased a McLane edger with this motor on it and it is not starting. I have to assume the throttle lever engages the speed lever down at the controls.
@RealManSkills
@RealManSkills 2 жыл бұрын
This came off of a McLane edger. I updated the edger with a 5HP Briggs. (same style) When I updated with the 5HP, I didn't connect the cables. I just used the throttle controls on the engine.
@ericgutierrez8028
@ericgutierrez8028 2 жыл бұрын
So I finally had time to work on this edger 101-3.5RP-7 to be exact. The model # on this Brigg is 91202 1231 E1. I have to assume the last part of the number is from the "type" stamped on the plate. Just researching the web leads me to that. Hope I am right lol. Anyways, I believe I need to replace the whole carb on mine. I tried cleaning it but it's in bad shape and I'd rather just replace the whole piece. Problem is, I can't find any parts for this with the model number I have. Can you give me some direction to help me find a new crab?
@RealManSkills
@RealManSkills 2 жыл бұрын
@@ericgutierrez8028 A simple internet search with that engine model number turns up numerous parts suppliers. The carburetor is part #499492
@ericgutierrez8028
@ericgutierrez8028 2 жыл бұрын
Do you know of any site that would still sell this carb? I have looked online and everywhere is saying the carb has been discontinued
@RealManSkills
@RealManSkills 2 жыл бұрын
@@ericgutierrez8028 looks to be discontinued but I am sure there are substitutes. I got something similar from ebay and amazon.
@midgyrich
@midgyrich 8 жыл бұрын
so this engine is from 2003, I believe by looking at the numbers
@RealManSkills
@RealManSkills 8 жыл бұрын
+Mitchell Richardson - I believe you are correct. According to the "code", this engine was manufactured on September 26, 2003. Thanks for watching.
@midgyrich
@midgyrich 8 жыл бұрын
+sblg43 Yes sir.
@skirtdevil
@skirtdevil 9 жыл бұрын
Nice video!!!!!!!
@RealManSkills
@RealManSkills 9 жыл бұрын
Thanks for watching!
@erikcreamer4762
@erikcreamer4762 7 жыл бұрын
Hello was wondering if there's anyway to removing that type of governor , have that same engine was just trying to find out how to set up a throttle for a minibike/gokart
@RealManSkills
@RealManSkills 7 жыл бұрын
I have never set up a minbike/gokart, sorry.
@erikcreamer4762
@erikcreamer4762 7 жыл бұрын
do you know if its possible to remove that governor
@RealManSkills
@RealManSkills 7 жыл бұрын
Sure, you can just disconnect the linkage, or take the whole linkage and blade off.
@erikcreamer4762
@erikcreamer4762 7 жыл бұрын
i removed the butterfly governor, very easy and works great
@RealManSkills
@RealManSkills 7 жыл бұрын
Good to know!
@Bobi-Boba-potantsyem.
@Bobi-Boba-potantsyem. 4 жыл бұрын
Спасибо тебе мужик.
@RealManSkills
@RealManSkills 4 жыл бұрын
Рад был помочь! Спасибо за просмотр.
@robertdecker8845
@robertdecker8845 7 жыл бұрын
Thank you for doing this video!
@RealManSkills
@RealManSkills 7 жыл бұрын
You are welcome and thank you for watching!
Simple Rebuild on a Briggs Pulsa Jet Carb & Tank in 4K!
8:58
Baldeagle242
Рет қаралды 73 М.
1985 3 HP BRIGGS ENGINE REPAIR (part 1)
18:54
805ROADKING
Рет қаралды 74 М.
How To Get Married:   #short
00:22
Jin and Hattie
Рет қаралды 21 МЛН
🍉😋 #shorts
00:24
Денис Кукояка
Рет қаралды 3,4 МЛН
Will A Guitar Boat Hold My Weight?
00:20
MrBeast
Рет қаралды 244 МЛН
Briggs and Stratton 5HP - Carburetor Linkage Setup - 130212
10:00
Real Man Skills
Рет қаралды 426 М.
Throttle, Choke, And Governor Configuration | Briggs 3.5HP Engine
4:22
Fill's Lawn Care
Рет қаралды 40 М.
Secrets of Briggs Governor Speed Adjustment
13:15
Riding Mower King
Рет қаралды 62 М.
HOW-TO Briggs & Stratton Engine 8hp-17hp throttle and linkage setup
9:16
Small Engine Disassembly 3.5 HP Briggs and Stratton
17:54
Shawn Davis
Рет қаралды 44 М.
VINTAGE BRIGGS & STRATTON  - CAN WE SAVE IT?
35:56
Vintage Engine Repairs
Рет қаралды 40 М.
BRIGGS CARB REBUILD
38:14
CTSCAPER
Рет қаралды 428 М.
Perfect McLane in storage for almost 2 decades
17:22
Guys playing with tools
Рет қаралды 1,5 М.
Briggs & Stratton Classic Engine Restoration (3.5hp) Restauracija
36:35
How To Get Married:   #short
00:22
Jin and Hattie
Рет қаралды 21 МЛН