Briggs and Stratton plastic carb won't prime or start

Briggs and Stratton 300/550 primer bulb won't prime after main jet cleaning. Check to see if primer has an air leak through this side port. Seal off that port to get the primer to work.

[@selwyn76able]

After a disastrous arrival at a job with my new pre-owned mower I have spent all weekend trying to suss out the problem. Your video could not have been more perfect. Thank you so much. I'm up and running again. I have subscribed and will be watching more. ❤🙏

[@berardia4]

@@selwyn76able Thanks that means alot. Glad it helped.

[@minnehonk]

I always wondered what that plastic nozzle was for, than when my mower would not prime or run this video solved my problem, thanks

[@berardia4]

Thanks. Have no idea what it is for either. Please subscribe. Thanks

[@FateBoards]

found this video while trying to figure out what that piece was for. it appears like a hose is missing, but glad to see someone else had the same setup. I had to take apart and clean the carb, and my problem now is, gas is leaking out of that extra line.

[@berardia4]

Thanks for the comment. Gas leaking means the needle is not sealing.

[@barryestell6324]

Nice video , but I drill that very bottom jet out to .025 with a # 72 drill bit and that will make it run better , more power and start first pull !!

[@mikem5475]

Also had great success drilling out the hole, but i forgot what size

[@mikesalinger7169]

Mine is the same but never had a problem priming or starting

[@baddad5781]

I have to work on mine to. Its been in the shed for a year cause it had issues. Same mower, same carb on mine with same starting issues. I wonder if just a tiny amount of caulk or silicone on that tip to close the hole off, if that will work. A bit more of a semi permanent fix but idk. I've also had issues on this model with the brake cable grounding out the motor so it would run die, run and die. Have to deal with that to. Thanks for the video

[@TheCrittercam001]

Thanks Al...I have two mowers with those plastic jobs on them that I'll look into now that I'm armed with your well thought out info.

[@migueloliveira4211]

exactly the problem with mine ....you have hit it dead but thanks man....continue to watch

[@chefkdowg]

Yes, some models had a hose go from that white thing, to a hole on the primer side of the air filter.

[@jm-ve8ry]

My plastic white barbed fitting has no hole. perhaps some engines were fitted with the wrong one.

[@richarddossett6800]

What is that hose called I'm looking at

[@mikeburton1703]

exactly the problem with mine ....you have hit it dead center right on.....i could not figure why that doesn't have a little hose on it.....but thanks man.....i will continue to watch

[@berardia4]

Glad it helped you. Thanks for subscribing.

[@VentureWelding]

I am willing to bet, yalls mower, if it still isn't starting. It's likely due to the timing being off. There is a plastic gear beneath flywheel that has a arrow that should like up with corresponding sister gear that's also marked. This is what was wrong with mine after replacing carb and covering all basics.

[@grant1109]

Mines doesn’t prime and surges when it runs. It won’t run smooth unless I give a little pressure on the prime button while it’s running. Thoughts? I cleaned out the main jet and the carb. Has new gas

[@berardia4]

Did you try capping off the jet like in the video. Any help?

[@frankfaubert1927]

It's for the folks that don't take their finger off the prime bulb when they're priming. It's a messed up engineering idea. It reduces the priming bulb's efficiency by about 70 %. Priming bulbs worked just fine without the hole in the middle but God knows, we can't leave well enough alone. Engineers have to account for their paychecks somehow.

[@harper626]

can get a new carb on ebay for 10 bucks. quick and easy solution

[@trainmaster0217]

when I push the primer bulb just once it floods the spark plug with fuel and refuses to start. I have to take out the plug and wipe and blow it dry. put it back in and it starts right up. fuel comes out of the air cleaner housing when I prime it 3 times.

[@berardia4]

Sounds like carb flooding. Needle and seat not sealing

[@lisapeters5554]

thank you VERY much for the info, but for Gods' sake get a tripod.

[@berardia4]

Your very welcome. Glad it helped you.

[@DoctorRobert2009]

Still doesn’t work

[@berardia4]

Check to see if primer bulb is not fully seated, ripped or screws not tight to the carb