Brother, thank you so much for this vid. I nearly threw away two vintage briggs engines and thanks to your vid, I got them running back again. Wish you the best
@sixtyfiveford2 жыл бұрын
That's awesome. Great work!
@benzimmermann21972 жыл бұрын
Super helpful, picked up a rototiller today with the same engine, no spark, looked exactly as nasty as yours, cleaned it, set the gap, beautiful spark!
@sixtyfiveford2 жыл бұрын
Awesome
@Mr_Tecumseh6 жыл бұрын
I have a few of these engines, most have magnetron ignition, but I had a winter version of one of these engines from 1979, the sno-gard. I decided to delete the points and put an electronic ignition coil on. Since its a winter engine its better off, wont have to worry about moisture from snow getting in and fouling out the points, plus I'll never have to worry about the points going bad again. It made life easier too, because I didn't have to remove that clutch or flywheel. I just snipped the one wire removed the old coil, put the new coil on, done runs like a champ.
@sixtyfiveford6 жыл бұрын
Yeah, point free makes life easier.
@ddutcher154 жыл бұрын
Nice video man. Just got two vintage Briggs flatheads today. One will run but needs new tank. Other one needs points I'm thinking. That's what brought me here. Keep up the good work.
@sixtyfiveford4 жыл бұрын
Thanks man. These old engine are a lot of fun to tinker on.
@sixtyfiveford11 жыл бұрын
@Paul Rockach the engine Model, Type and Code numbers are located on the large engine housing (starter recoil on the front of it). They are typically on the left hand side by the carb. A flashlight at an angle in the dark lets you see the stamped numbers.
@sixtyfiveford11 жыл бұрын
Ebay... The nice thing about briggs is you can simply bolt on a non points coil and your good to go. No need to touch the points or remove them. There are 2 sizes of coils, one for the larger 8hp+ and a smaller one for the 2-5hp.
@mrjohnpdudley9 жыл бұрын
Thank you! Gave me confidence and the skills to fix my workhorse of a rototiller! Also appreciated your video about how points and condensers work. Thanks again!
@sixtyfiveford9 жыл бұрын
John Dudley You're welcome. I'm glad they helped.
@andreo12 жыл бұрын
Going to have to try this with an old tiller that I picked up for 20 bucks. I saw it run when I bought it. The following season I had no spark. It should be a fun weekend project.
@sixtyfiveford11 жыл бұрын
Carb would be my first check, but you've done that. Second I would check for a sticking valve.
@sixtyfiveford11 жыл бұрын
Really? That is just awesome. Tell her thanks for watching.
@genocide336611 жыл бұрын
While I was at work my mom watched this video and fixed the tiller. She says thank you!
@mustie113 жыл бұрын
nice vid, well done, hey do you use it for moving trailers around, as I see it has a ball mount,
@KIutch66612 жыл бұрын
great video, it helped me out with getting spark back to my motor. it runs now but only if i pour a little gas in the carb, after that gas is used up it dies. do you know what the problem is? i cleaned out the pick up lines with carb cleaner still nothing. could you possibly make a video showing me how to rebuild the carb or tell me how to solve my problem so it'll just start without me having to prime the carb. any help would be greatly appreciated.
@jasonmushersee13 жыл бұрын
Yeah the business card trick i used on the coil/flywheel for a honda 5.5 engine. Nice vid. Wish i had that tiller.
@williamwilliams32006 жыл бұрын
Thank you, I will get it started as is and see what happens. If need be, I will try the job weld.
@JOEZEP5411 жыл бұрын
Another great video.I have a Craftsman EAGER 1 Mower.It has a 6 HP Tecumseh. Will start sometimes & then stall. Have to wait a couple of minutes & prime , the same. I Though it was the Carburetor cleaned it up but the same. It does the same with starter fluid. I checked the fly wheel & the key alignment looked like it was off a little. The key is not sheared but has a very slight bend hard to see. Is this enough to have a no start?
@connorssmallengines66634 жыл бұрын
JOE Z yes, sorry I’m late but I hate too see comments that go unanswered
@sixtyfiveford13 жыл бұрын
@mustie1 Yes I do. I have another video here on KZbin where I move around a small trailer.
@micronautseven3 жыл бұрын
Great video, it came off just like your video, thank you for the info!
@sixtyfiveford3 жыл бұрын
Thanks for watching.
@skipwadoo10 жыл бұрын
Runs like a champ !
@sixtyfiveford10 жыл бұрын
That's great.
@donaldbrown332610 жыл бұрын
+sixtyfiveford
@sixtyfiveford12 жыл бұрын
If it does start it will not sound good. It will also rip the pull cord out of your hand when you try to start it.
@sixtyfiveford11 жыл бұрын
Any luck finding it?
@Mr_Tecumseh6 жыл бұрын
You mention in the beggining of the video Briggs made a 2hp and up maybe a 1.5hp. This guy I know has an old Briggs from the 50's and the engine he has its like a 1,1/4 or 1,3/4. I forget exactly but it wasnt a 1.5. It was a real odd ball hp wise and small less than 2. Are those rare? He only wanted 10 bucks for the thing, it isnt in the greatest shape, but its pretty much all their and that odd hp tag is still on it. Should I grab that the next time I see it for rarity maybe a little value to it more than the $10 he wants? I'd basically be saving it because it just sits their.... In fact come to think of it, it was like a 1, 1/8 horsepower, a real oddball and Ive never seen an engine with an hp rating like that.
@sixtyfiveford6 жыл бұрын
It's old if it's a fractional horsepower like that. More than likely a washing machine motor. There's a little value there but more of a conversation, fun to tinker with piece.
@doogie5253 жыл бұрын
Great video
@sixtyfiveford12 жыл бұрын
Not always but sometimes.
@babennewport12 жыл бұрын
great video. while i was taking the screen off that's attached to the flywheel on my 3hp it separated that spinning mechanism and the balls or bearings came out. can it be salvaged, i can't figure out how to seal the two haves. Thanks
@sixtyfiveford12 жыл бұрын
I have a video up of how to do this style carb. Go to my videos and it is the one titled "Horizontal Briggs Carb Rebuild part 1 of 2" and 2 of2. . It is more than likely the little diaphragm on the side of the carb.
@Madeinwem4 жыл бұрын
great video, thank you....
@Thedaveyht37 жыл бұрын
do I need to worry about or set top dead center when re- installing the flywheel? and I need .020 when the points are fully open or closed?
@sixtyfiveford7 жыл бұрын
.020 open. Top Dead Center isn't required, just reinstall the flywheel on the key where ever it is.
@500passwords13 жыл бұрын
nice work buddy . thumbs up from 500
@boxing4life2589 жыл бұрын
sixtyfiveford hi mate i see your comment below i have a brigs n stratton trojan 2.5 i took it apart as it was running sluggish like cutting out then it did completely cut out and wouldt start so i thought a petrol problem i took carb out and i think it was the tubevwith gauze that goes from tank to carb was blocked anyway i put it back together and im not getting a spark ive cleaned the fly wheel set the magneto correctly and a new sparkplug and still no spark could it be the points or what is the problem as your comment says its not the points?? Thnks
@sixtyfiveford9 жыл бұрын
boxing 4 life If you aren't getting spark: first check to make sure the kill wire isn't being shorted out to the engine. If that is fine then it is your points and condensor. Generally it is just dirty points though.
@williamwilliams32006 жыл бұрын
i broke off one of the aluminium fins on the flywheel, will that put it out of balance too much? i haven't got it all back together yet.
@sixtyfiveford6 жыл бұрын
I've seen fins broken off but never noticed any balance issues. The nature of a single cylinder is a lot of vibration anyway. If you want, you can snap the fin off the other side to balance it, or put a glob of jb weld/epoxy where the broken fin is to add weight.
@jeffhopkins22783 жыл бұрын
Yeah they made a 1/2 h.p. washing machine motors. WM. WMB
@beccam10075 жыл бұрын
My dad wants to find a wiring diagram for points on briggs and stratton 14hp. Do you know where I can find one?
@sixtyfiveford5 жыл бұрын
There really is no wiring diagram. You need to refer to this video for a 14hp single kzbin.info/www/bejne/h4LUmal3ataiaMU One wire goes from the points to the coil. One wire comes off the coil and touches nothing unless you want to stop the engine(kill wire)
@sixtyfiveford12 жыл бұрын
GREAT.. $5 for a trash pump is a great deal.
@TheMrBenShady7 жыл бұрын
Do you know what the 'model type code' is on that engine?
@WammSon9 жыл бұрын
thank you sir.
@sixtyfiveford9 жыл бұрын
William Williamson You're very welcome.
@foreverwood19639 жыл бұрын
good job
@sixtyfiveford9 жыл бұрын
foreverwood1963 Thanks Man.
@railroaded19913 ай бұрын
Would have been great more lighting, closer views, better camera angles, no arms in the way hiding what you're doing, less patter about things that don't matter.
@ae86miami7 жыл бұрын
Good way to damage a good extension, why not get a punch set