ABS and Stability Control Fix, Free Airbag Fault Fix and Project COST! | VE Commodore Daily Part 3

[@BrowneysGarage]

Huge thanks also to anyone who has enjoyed this short series with us. Back to work on the BA Falcon!

[@zoe-leesweeny8625]

I love my ve sv6, and its getting to an age that these vids are handy as.. cheers!

[@RobertB56]

I've just found your channel and immediately subscribed as a VE owner it's a must.

[@BrowneysGarage]

Awesome, thanks very much mate 👍

[@kathytukavkin2522]

Hey, that's me as well 😁

[@starrettveavea2716]

Thanks very much for your tutorial. Exactly what came up today. ABS and that annoying Airbag light. Great to see Aussie content on the tube. Keep up the good work mate.

[@BrowneysGarage]

Hey thanks for watching mate, glad you enjoyed 👍

[@johnlovell2082]

Had the same problem with my VE Wagon...ABS Stabillity Ctrl fault. Replaced rear ABS sensors and rear loom but this was not the problem. This can be caused by low amps in the battery. I replaced the original battery with a new AC Delco one from Holden dealer and this fixed the problem. Have had no problem since....these newer cars need spot on electrical supply. Even if the battery shows good voltage it may not have the amps....best to get it load tested first.

[@tejanpillay8245]

Yup happened to mine too. Quite a few faults popped up when I had a battery on the way out. Gearbox too iirc. Definitely test your battery before anything else!

[@jamesvincent3405]

your a legend tried all these threads on car forums to get the airbag off and everybody was so trash just wish i found you sooner

[@BrowneysGarage]

Thanks mate. Glad it helped cause I wasn't terribly sure I explained it well either!

[@leighporter8417]

Thanks for the video, helped me out a lot, solved my ABS issue, really appreciate the effort you put in to it.

[@BrowneysGarage]

@Leigh Porter Thanks for leaving a comment mate, it's great to hear that these videos have helped some people so I really appreciate it.

[@Steven-te2me]

Legend! This video saved me $$$ I didn't see any obvious damage to the wiring loom so I got myself a multimeter and checked the sensors and sure enough one of them was reading 27 units of resistance. Ordered a new speed sensor $55 (trade price) installed it and took the car for a drive around the block and all the error codes turned off. Thanks mate!

[@BrowneysGarage]

Nice when it's an easy fix isn't it? If only they were all like that. Glad we could help mate 👍

[@Sean-uy3cu]

What error codes did you have mate? Did you get check engine light also?

[@Steven-te2me]

@@Sean-uy3cu from memory abs, stability control and traction control

[@haaretewehi6469]

I'm definitely trying this over the airbag fault turning on and off every 5 minutes. Awesome vid mate

[@BrowneysGarage]

Got incredibly lucky with that one, hope you do too 👍

[@paul_from_diamond]

Amazing video mate. Super impressed in how thorough, patient, and professional you were throughout the video. Few funny kickers in there too good job mate I appreciate it

[@jon50334]

I brought 1 for 500 bux. Has been great. Had dent guard but replaced * new tyer rods and sway bars and going well and was owned by tatslotto lol as iv got manual to it. Beautiful car to drive. It got my licence back after 10years :-) 🎉🎉

[@idoskidsattheawesomeauzzie9255]

Your a LEGEND Buddy… a Mountain of Helpful Knowledge

[@BrowneysGarage]

Not sure about that, maybe closer to a "small mound of passing info along as I work it out"! 🤣 Thanks very much mate, glad you enjoy.

[@johnchilcott8620]

Hi thanks for sharing your video about abs fault stability control fault,never had a code for mine though,changed left side sensor and worked,so i changed both rears..cheers! New subscriber..

[@BrowneysGarage]

Legend, thanks mate!

[@tomislavkobilarov5704]

On my ve Commodore I fixed same problem by replacing battery with brand new one and after that newer had those vornings!!!

[@nancywosomo6621]

Thank you, I'm actually going through the same problem, Will definitely do this 🙏 And will let you know the outcome 🙏 Thanks again

[@scottneulist9495]

I don't even own a VE, just love your content

[@BrowneysGarage]

Don't buy one! Not really, has been pretty reliable since we got it sorted. Thanks for watching, glad you enjoy what we're doing. Plenty more in the works at the moment 👍

[@etonvainerere2192]

Thanks for this video. Helped me alot. Tyvm

[@BrowneysGarage]

Glad it helped and thank you very much for your support mate 👍

[@user-rb6ie2ss7g]

Excellent work, great video and hints , thanks. Now the thermostat on my 2011 Berlin’s 3 litre is leaking coolant , very common at present in Perth with cars around 200K , it may be your next issue!

[@AndyIronsides]

Nice Browney, got the same problem, thanks for advice mate

[@BrowneysGarage]

No dramas mate, good luck 👍

[@dagamecheats]

Just bought a new rear wheel sensor for my 2012 ve... hopefully it’ll fix the problem! the scanning tool said it’s a rear wheel sensor issue so fingers crossed

[@BrowneysGarage]

Fingers crossed mate, would be the easiest fix for the issue I’d say.

[@dagamecheats]

@@BrowneysGarage hey just an update, speed sensor came in the mail, whacked her on... error codes are gone! you’re a life saver mate, this is coming from someone who knows nothing about cars so cheers mate!

[@BrowneysGarage]

@@dagamecheats You beauty! Doesn't always happen but man is it nice when it's an easy fix. Thanks for the letting me know, I do love hearing these videos have helped people, and all the best!

[@darrylcampbell4411]

Awesome vid. Thanks Brownie. big help. can only imagine how much the clowns at my local garage or holden dealership would rip me for these simple jobs. cheers Bro.

[@BrowneysGarage]

I got lucky with some of these fixes for sure but yep would hate to see what a really dishonest shop would have stung someone for this. Thanks mate 👍

[@wigletron2846]

Thanks for the video. Have a G8 and right rear abs code. Looks simple enough thanks

[@BrowneysGarage]

If I can do it pretty much anyone can! Thanks for watching and good luck.

[@shanehat444]

Yahoo thanks very very helpful.. Love Yr dry humor..

[@BIGO.CHILLIN.SIDEWAYS]

This was a very helpful video thanks!

[@BrowneysGarage]

Thanks mate 👍

[@goodjah]

Bloody great video mate thank u

[@BrowneysGarage]

No problem 👍

[@zachooton6036]

holy shit that plug takes the cake for petty problem compared to falcon little bit of plastic that always snaps when you wanna take your radio out

[@timpipe2594]

Very good.

[@dcr1545]

On my SS I had same faults. It was the left rear wheel bearing and a bad connection to the alternator

[@nicholepomare2419]

Did this cause a check engine light to come on to?

[@dalechenoweth915]

Hey Man, great video. My WK statesman has all those lights on the dash and more. ABS fault SRS fault Trac off Check engine Service fault-contact retailer. but they are only there sometimes and not other times. They always appear together, all at once. Also the aircon does not work while the warning lights are on, and the instant fuel consumption readout remains at 0.00L/100Km. I refuse to believe all of these systems each have an intermittent fault which appear and disappear together. I'm totally stumped by it and I'm a long way from a Holden dealer.

[@BrowneysGarage]

Yep I’d say you’re right in your thinking that all of those can’t just happen to go wrong at the same time, even my luck isn’t that bad. Sure you’ve come to the same conclusion that it’s probably something electrical going wrong, that would be my thinking anyway but I’m far from your best resource for this. I’d be thinking a BCM issue, loose connector, bad earth, something like that? Sorry I can’t narrow it down further mate, and could be completely wrong. Maybe try the usual Facebook owner groups, forums etc. Best of luck mate

[@Spideritems]

Tried for half an hour to get this airbag off, I guess it’s something you need “the knack’” for which I obviously don’t have, I’m gonna quit before I break something and just put up with the airbag fault until next service.

[@BrowneysGarage]

@Patrick Hake It’s definitely fiddley, one of those jobs that seems much easier once you fluke getting off once! Try the tape over the light trick, won’t help with the annoying dings though. Thanks for watching mate 👍

[@daeltonsarahjasminyebarbos4858]

Very good, no meu carro não marcava nem o hodômetro também, Brazil ✌️

[@JB-el3se]

Stupid question time Do codes wipe themselves or is there a sequence of buttons to push or do I have to pay for scanning tool As I have replaced rear loom and still abs traction on So was just going to replace both rear sensor Great vid Cobba very easy for this uneducated car enthusiast to understand

[@BrowneysGarage]

No stupid questions, but remember this reply is from a stupid man! The error message on the screen you see should clear itself if the issue has been solved. Not sure exactly what period of time it takes this to see the signal is now corrected to do this but I couldn't imagine it to be more than a couple start/drive/car off cycles. A point worth noting too, replacing the sensors isn't 100% fix either but seems to generally sort it. I am dealing with the recurrence of this issue now and seems to be related to issues with the tone wheel these sensors pick up from or another electrical issue - always something else to fix! Hopefully you're luckier than me. Best of luck mate and thanks for the kind words.

[@RN-mn3zu]

Tried the airbag trick…. Clip was fine lol… at least I know mines ok hahaha

[@BrowneysGarage]

Worth a try, man I got lucky on that one!

[@deanhotton824]

Brilliant presentation. Very easy to follow and understand. Could you let us know wat your diagnostic tool is pls. I have a vz crewman 2007 and i,d like to purchase the diagnostic tool code reader if possible. Cheers much ll 😊

[@rqn1998]

Mate im getting a p0101 maf sensor issue ive changed the maf obviously along with all sorts of vacuum leak checks... the esp off comes on and code back constantly... any ideas? Ive tried everything now?

[@doobee84]

Thanks for the vid, going to give this a go and see if it helps with my ABS issue also.

[@BrowneysGarage]

No problem, and good luck mate 👍

[@vtmcmermods1335]

I have these warnings flash up when i accelerate onto the highway then a minute later it goes away. Could it be a Battery issue?

[@TheDiamontsr4ever]

Great tumoral for the abs sensors, do you have a mechanical shop? And where?

[@201kylie]

I’ve got voice in displayed on my dash it won’t go away. Does anybody know how to get rid of this

[@mw292]

Make sure the PCV valve isn't blocked, or you'll do a timing chain

[@giterdunpete]

How do they relate to each other?

[@garybrodziak2196]

@@giterdunpete oil pressure keeps the cam chain tensioners correct tension, if your pcv is blocked oil pressure will drop, chains will start slapping about, overheat with reduced oil flow and stretch, next thing you know blown engine. the pcv is on the left hand rocker cover at the rear - tricky to get to.

[@mrmayhemstewart5138]

Excellent job mate thanks those faults have been driving me crazy liked and subbed now how do I fix the seatbelt from telling me it’s not done up the bastard of a thing thanks again cheers Yogi 🇦🇺🤙🤙

[@tgg449]

Trip button turns it off as well but come back on every time u start your car

[@BrowneysGarage]

If only it were that easy to fix it 👍

[@alfonsomaravilla6295]

Cheers mate

[@rhyshiscox9386]

I have a front right wheel speed sensor fault mate. Do you know if that's a whole hub replacement or does the sensor come away from it? At quick glance it looks like part of the hub. Can't find any info, only rears.

[@BrowneysGarage]

Haven't actually done one myself sorry so not sure if there's a trick that I'm missing but by the manual I have here it says "The front wheel speed sensors are integral with the hub and bearing assemblies. If a front wheel speed sensor needs replacement, you must replace the entire hub and bearing assembly." Unfortunately it sounds like you've nailed it mate, bit of a pain in the bum for what could be a small job.

[@rhyshiscox9386]

@@BrowneysGarage I was afraid you were going to say that. Haha thanks for the reply though, much appreciated. Thumbs up.

[@brendoncooper5330]

Do u have a video of where the speed sensor in the gearbox or on the transmission

[@kemorei]

Huge huge thanks for sharing your knowledge.. by the way i have 2007 Lumina V6 can you pls help where is the switch for turning on the fog light. Thanks in Advance.

[@BrowneysGarage]

@Reinhard Baddal Thanks mate. On the fog lights, couldn’t tell you off the top of my head as my POV pack VE doesn’t have them but try your owners manual.

[@nurullah5845]

To operate the fog light is simple as pulling the headlight switch towards you it pops out a little and activates your fog lights to turn it off just push it back in and that simple.

[@kemorei]

@@nurullah5845 thank you so much buddy it works now.😘

[@BrowneysGarage]

@Nurullah Legend thanks mate 👍

[@bundak77]

Your awesome.

[@nelsonsoto699]

Thankyou, your videos help me a lot, Im subscribet too.👍😊

[@chaukemt]

hello thanx for the video, but i still have issues with my ve SS v8, it has stability control fault, i have changed the rear speed wheel sensor and the problem still persist. it keeps ESP off. please any idea as to what else can i check or replace,.

[@NoobiesAstig4x4]

Good video mate., Can you please put the Part No. of the Loom Harness of ABS Sensor? Thanks.

[@BrowneysGarage]

Part numbers are in the video description, but here they are too👍 Rear ABS Speed Sensor - 92211237 (ebay.us/8Pt7m3) Rear Speed Sensor Wiring - 92257573 (ebay.us/Pr5rZB)

[@mickeyharryful]

hi i have a 2006 ve hsv clubsport and the stability and abs and the check engine light is on theres a plug thats quite large hanging down on the drivers side rear any ideas many thanks and great video by the way

[@BrowneysGarage]

Hi Mike and thanks. You may have answered part of your question there, ABS/Stability could definitely be related to the wiring plug hanging at the rear. Unfortunate though the check engine light is a bit of a ‘how longs a piece of string’ and I don’t know the engines well enough. I’d suggest picking up a code scanner and starting there, should give you much more info to go off. Hope you get it sorted mate

[@josiahoakley8656]

Anyone know what size torx bit you need for the abs sensor?

[@ragingbar]

Having stability control fault come up every now and then but it's not logging the code, as soon as it happens my car goes out of wack. There also is a misfire but I'm getting that fixed a bad coil I think.

[@mr63249]

What scan tool is this and where can I get one thankyou

[@abs1784]

Thanks for the video. Do you know why the stability control light comes on my ve omega0 08? Do you know what's the course?

[@chubblezromana6114]

My holden has gone into limp mode, is that beacuse of my abs light and stability control? The diagnostic scan said rear left speed sensor, and front right speed sensor.

[@themanager0076]

Great video, love the casual nature. Tip, as you pit in. You should always de-energize the air again before removal.

[@roelb3596]

Can I ask a stupid question, I have replaced Left rear sensor, still error light. Then checked cable, has continuity on all poles. Do I need to ask the dealer to reset the codes?. Or disconnect the battery for 30 min?. Car is 2012 SSV. Thanks

[@rolandoreyes182]

Hey buddy thanks for your videos, quick question is it just one wiring harness for both rear sensors or one harness for each one ?

[@BrowneysGarage]

@Rolando Reyes Thanks mate. Just the one wiring harness covers both sensors.

[@Steven-te2me]

So this problem has popped up again after I successfully replaced a faulty sensor about a year ago. I thought maybe it's the other wheel sensor but that's reading about 1.16 resistance. I took the wheel sensor out I replaced about a year ago and that is reading nothing. Now I don't know much at all about electrical. Does the nothing reading mean a faulty sensor as well? Cheers

[@brucehamilton7663]

My engine check light comes on every time I start the car. How does one get it off? The car runs fine so it must be reporting a misfire perhaps?

[@shay7731]

Do you why I would be getting a abs/stability control fault only when I apply the smallest amount of throttle? I can turn the car off and leave it for 2mins and start again it goes away but once I start driving it comes back on..

[@BrowneysGarage]

Not sure why it would be coming and going like that, are you clearing codes when you turn it off? It's normal that the ABS/Stability Control fault wouldn't come back on after being cleared until you move the car somewhat, then the bad sensor will show a much different reading to the other wheels and trigger the code. Sounds like bad wheel speed sensor or related to it.

[@gamd7075]

This is fuse #1 in the F1 A10 SIR internal valve unit, right or not.

[@poogzie]

Hi , nice vid , can u tell me the model of the code scanner cost and so forth .cheers

[@BrowneysGarage]

Thanks mate. It's an Autel Diaglink MD802, cost is $129 shipped and that gives you every model for one manufacturer eg. Holden. It's another $10 I think for each manufacturer after your first one. Really happy with mine, there's been nothing yet that it hasn't been able to find and show. Here's a link to the same one: ebay.to/2ocr3OA

[@abzhama3402]

Hey mate love the videos! Quick question, got me a ve Berlina 06 model and me engine light came up, put it in the scan tool and come up with “p0171 system too lean” any idea on it bud?

[@BrowneysGarage]

@Abz Hama Haven’t dealt with it on this car but maybe oxygen sensor or exhaust gasket leak? Search it up on any of the Holden forums, I’d be surprised if it hasn’t been discussed there. Good luck

[@smokinbtch298]

So this morning I started my VE Berlina 2011 an I could tell immediately something wrong engine sounded diff an kinda shaking then check engine light an stability control issue popped up. Is this the same problem an should I just go ahead an change wiring

[@Ddaniel_xoxo]

ive been having saftey mode issue now for almost a year, ESP off , saftey mode power reduced, the car has 19s and is lowered, with full Xforce exhaust, can i jsut go get the car tuned and stop it from going into saftey mode or do i ned to put 17s back on the car and the stock exhaust to fix this issue in your opinion (car was baught with all these mods alrdy done, i wouldnt waste money on a omega personally)

[@ltdustycro2624]

Great vid mate, any chance you would know where I would find the yaw sensor in a 06 Omega? Thanks in advance mate.

[@BrowneysGarage]

@LtDustyCro Thanks mate. Haven't had any experience with it sorry so anything I can say would be purely from searching as I'm sure you've tried.

[@wonkychikn]

From memory the yaw sensor is near the bottom of the b pillar ..very small sensor with a TX fitting rod sticking out of it ...do not confuse it with the bigger rectangular sensor ,as the rectangular sensor is for side airbag system.

[@tamikaduckworth5077]

Hi mate I have a wm Caprice V8 and it's doing the same thing but when the codes come up no power pls let me know??

[@milliefranks2046]

How do I access codes on screen

[@captainsensible6939]

I've obviously missed 1 and 2, so, safety third.... I'll stop going back in time for now.... I'd like to also raise a plausible point though, while I'm going backwards through time catching up with your vids, and, I'm still here, why is the speed sensor on the rear left wheel and why is there a need for plausibilty, could the paradigm relate to the fact that not only the left wheel rotates? Asking for all the black holes

[@captainsensible6939]

OMG, I just noticed how old this is..... I've gotta stop living in the past, sorry Browney, your Dad jokes are still shit lol

[@tompetty8531]

I've got a vy SS and my TCS pops up and stays on lose power and not save any idea

[@brockturner8430]

Do you have to reset the fault or does it clear automatically?

[@BrowneysGarage]

Depends what code it is mate. ABS/Stability Control I believe if it's fixed will clear after some driving and the car seeing all is good again.

[@georgeanastaangler8757]

Bro can you please fix my ve ssv! Ive payed a mechanic over 4k and the problem has come back after 1 year of not using it after the problem was fixed

[@robmackie4460]

Hey mate my 07 6ltr calais I brought last week after 1 week faults started coming up Stability control makes engine run rough an check engine appears.. stability control first then about 5 mins check engine comes up.. weird thing is turn off an start again it's fine for about 5 mins then same stuff

[@BrowneysGarage]

Sorry mate you’d be best to chase this up on a VE owners Facebook page/forum. Sure there’ll be much more knowledgeable blokes on there who can lend a hand. Best of luck 👍

[@walkinshaw457ssv6]

Hi quick question. I just changed the wheel speed sensors on both sides. I started the car up and it’s still showing the abs and esp faults. Do I have to clear the codes and if I have to how do I clear the codes. If it’s not the sensors. What else could the problem be.

[@BrowneysGarage]

@Walkinshaw 457 Ssv Ideally if you can, clear the code and if it comes back immediately you know it hasn't been sorted. If you haven't got a tool to clear the code with then I believe after some driving and a number of start ups the code will clear itself if sorted - not exactly sure on how long that would take though. If not the sensors then could be the wiring as shown or I believe it could even be an issue with where the ABS Sensor picks it's sensor up of the back of the hub being dirty/not conducting correctly for a signal. Haven't personally tried sorting this way yet and not sure how much access there is but perhaps some compressed air in the hole where the senor goes while turning the brake rotor could clear it out enough. Good luck mate.

[@walkinshaw457ssv6]

Hopefully the fault will clear after a few drives. If it doesn’t i will blow some air in the hole that the sensor came out of as the old sensors had slight rust dust on them. Cheers for your help with this.

[@BrowneysGarage]

Can’t guarantee I’ll be of any help so not sure you should thanks me yet! But no problem mate, hope it gets sorted 👍

[@walkinshaw457ssv6]

Browney's Garage thanks anyway. Any information is good information as I have no idea as I was hoping all I had to do is plug and play. Just trying to narrow down the problem starting from the easiest first.

[@nicholepomare2419]

Awesome vid very helpful, just wondering what type of scanner do you use? I’m forking out 110 for every scan at a work shop? Also would it work on a ssv ve? Thank you sub to you 😊

[@BrowneysGarage]

Hey mate, the scan tool used in the video is an Autel Diaglink - will pay for itself in one use! Thanks for watching 👍

[@Delta088]

Hey brownie..Were did you get the abs wiring loom.

[@BrowneysGarage]

Links in the video description but I've copied it here for you too, good luck - ebay.us/Pr5rZB

[@nayeemsaleem3971]

hi brother, Thanks for the video. I have one question, I am having stability control off light in my dash for holden commodore 2008.completely deactivated even if i press the button to activate. No issue with the ABS its working fine. Could it be the bad wheel sensor or any other issue?

[@BrowneysGarage]

Hi mate, thanks! As far as your issue I am definitely not an expert on these but to me I would expect a bad wheel sensor to always throw an ABS Fault as well. Is there any engine light on as well? Have you scanned it for codes? I'd be thinking there may be another bad sensor in a system other than the ABS/brakes but haven't personally dealt with this is sorry.

[@nayeemsaleem3971]

@@BrowneysGarage Thanks for the reply. There is no check engine light. Does it need to reprogramme? Anyways thanks a lot for your valuable comment.

[@BrowneysGarage]

Sorry I can't be more help but I'd start by picking up a code reader if you're looking to fix this or any other issues that come up in the future. Should help to give you more info on what's wrong. There are very cheap units on eBay that may be ok, the one I have is slightly more expensive but has been amazing - here's a link for that one - ebay.to/2ocr3OA Hope it works out mate, let me know if you get it sorted 👍

[@nayeemsaleem3971]

@@BrowneysGarage Thanks mate. Appreciate your response.Sure i will check the link and try with the scanner. :-)

[@swbaligac]

Great vid.. how did you find the faulty sensor.. or did I miss it😋

[@BrowneysGarage]

Sure it was in there but it’s been a while, scanned for codes and indicated it was likely the sensor.

[@victoroneill4381]

Hi what scanner do you use to reset fault codes. thanks

[@BrowneysGarage]

Autel Diaglink MD802 ebay.to/2ocr3OA

[@vivamoment]

Great video! Thanks. Say, I purchased a scanning OBD2 tool and I get a "U0101 - Lost Communication with TCM" fault code. Do you know where the TCM (Transmission Control Module) is located in the VE Commodore? I can't find documentation anywhere, and Google has not been my friend with this one. Please let me know.

[@BrowneysGarage]

I don't sorry mate and I'd just be starting with Google too. Try JustCommodore forums or an owners group on Facebook? Good luck mate.

[@vivamoment]

@@BrowneysGarage Thanks for the quick reply. I am on JustCommodore, but can you suggest a good, (or how to find a good) owners group on Facebook?

[@michaelmarshall8180]

Hi I'm looking for the fuse for the air-conditioning.

[@BrowneysGarage]

Have a look under the fuse box lid for 2 labelled HVAC, may be what you’re after.

[@punzbarton8007]

Hey Browney i have a VE & my airbag light comes on everytime i start my car does that mean 1 of my plugs is not in properly like how u showed in your video? Because everytime i turn & music is playing it will skip the song / turn volume up & down all the time its very annoying please get back to me when u see this mate cheers!

[@BrowneysGarage]

Could be but I was extremely lucky for my issue to only be this. Definitely sounds like you have some sort of wiring or earth issue going on though mate, couldn’t hurt to start checking over all plugs, connections etc. Sorry i can’t be more precise than that mate, wiring can be a dead simple fix or an absolute nightmare!

[@punzbarton8007]

@@BrowneysGarage Cheers brother i will check over it tmrow & let u know how i go 👍🏽

[@nicholasbrook3604]

legond where do i send the cartoon

[@asimrc]

Hi mate I changed the rear wheel sensors and cables still getting stability code error. do you rekon it could be the front sensors that need replacing? Has your code ever come back since the repair?

[@BrowneysGarage]

You'd really just have to get a code reader/have them read by someone to narrow it down mate, could be much cheaper than throwing more parts at it unfortunately. Sad to say that yes, mine did come back. Seems it's normally the sensor or wiring but looking like mine has to be difficult and have another problem, have played around with it and these still seems fine. My next guess, and remember I'm a complete hack and it is a guess, is that it's the ABS tone ring that the wheel speed sensor reads from in that back corner. Unfortunately it means popping the axle out of the rear hub to inspect/replace and so I haven't got round to it yet and just put up with it having no ABS/Stability Control.

[@asimrc]

@@BrowneysGarage mate I'm a hack just like you. Finally hit 400k km. I have an obd 2 reader for some reason traction control error never shows on that. Axles stuff is too complex for me im gonna try the front sensors will let you know how I go.

[@rohanhayes9493]

How many sensors are there on the car?

[@BrowneysGarage]

Wheel speed sensors?

[@michaellast1385]

I have a 2010 ve omega. Sometimes when I start it (especially when cold) It idles bad, sounds like its about to die and the entire car shakes. An error appears on the screen about stability control, then check engine. I turn the car off then back on and its fine? Seems to only happen when cold, mechanics are stumped, Happens about 1 times out of 20.

[@BrowneysGarage]

@Michael Last Sorry mate I'd be just guessing having not had quite the same issue. Perhaps try an owner's group forum or Facebook page? Good luck mate

[@brownhornetseventhre]

so if i did this myself how can i get the codes reset. currently stuck on side road waiting for a tow due to stability control limp mode.

[@BrowneysGarage]

I could be wrong but I never had a limp mode caused by the rear sensor, may be worth scanning to confirm? If it is a wheel speed sensor and you replace it the code will clear itself after some driving. Good luck 👍

[@brownhornetseventhre]

@@BrowneysGarage ok thanks. so I'd actually run out of lpg on my way to the servo, but I had stability control senor limp mode before I ran out of fuel. RAA tech reset two fuel pressure codes and the stability, i no longer have an issue...strange.

[@BrowneysGarage]

@@brownhornetseventhre Hey if it works you may have got away with an easy fix! Fingers crossed.

[@yarn3273]

Nice work, will a (abs) scanner see (esp) faults?

[@BrowneysGarage]

@Yarn Thanks mate. Not 100%, depends on the scanner, but if it can scan ABS codes then probably can cover those as well.

[@gamd7075]

هاذا هو فتيل رقم 1 وحدة صمامات الداخلية F1 SIR

[@johndee68]

Can you send me what the product item is for your black gloves?

[@BrowneysGarage]

They're just disposable nitrile gloves, any auto store will likely sell them.

[@ryanlicastro3041]

How did you reset your codes?

[@BrowneysGarage]

@Ryan Licastro Hi Ryan, this was done through the code scanner. I have been using an Autel DiagLink, here's a link to the one I use. Pretty good unit, good luck mate. ebay.to/2ocr3OA

[@ryanlicastro3041]

@@BrowneysGarage thanks mate. I just found out Supercheap Auto can reset for you $14.

[@BrowneysGarage]

Nice, not bad at all.

[@MrWah79]

@@BrowneysGarage hey Browney. Great vid mate. I've got the VE series 2 wagon, the misso has a subaru forester. In regards to the OBD2 scanner, have you found any codes that the unit can't diagnose? I'm looking at buying the unit because our cars are starting to get a few years on them, and now that holden is pulling the pin I want to sort out as much as i can by myself. If you were going to buy a new scanner today, would you buy the same one? Cheers.

[@BrowneysGarage]

@MrWah79 Hey mate, I’ve definitely been happy with the scanner I picked up. No expert but we tested it out pretty well and looks very well supported so should cover all codes as far as I can tell, now and going forward. Only downside is the cost and that it then costs roughly $10 for each new manufacturer you want (comes with one but would need another for Subaru for example) but seems pretty reasonable still, to me anyway. Best of luck mate 👍

[@callumfreebairn8082]

australasia's no 1 selling car

[@asimrc]

Hi mate have you ever had a p0430 code if so what did you do to fix it. I have a high km omega it has 395,000 km on it.

[@BrowneysGarage]

I haven’t sorry mate, to be honest I’d just be searching and rewriting an answer from elsewhere that I hadn’t tested. Best of luck with it mate and good to see these things still going well in the high kms, I’m nudging over 290k kms in this one now.

[@mitebcool]

GM engineers were like shit that would be easy for the owners to fix actually, better make it a torx bolt at least.

[@BrowneysGarage]

I can definitely see that conversation happening!

[@rejh5678]

🤘👍

[@BrowneysGarage]

@Rej H Thanks legend 👍

[@vantomz3935]

U want to fix my car? Vy commy. Srs light and abs both going off

[@MichaelKingsfordGray]

Bogan grammar!

[@locallyhated1188]

no ones cares about broken Holdens its cringe

[@locallyhated1188]

Accept a few people but