DIY process for Electric Foil construction Material used Infusion resin www.easycompos... Gelcoat for mold www.easycompos... Coating resin www.easycompos... Unidirectional CF www.easycompos... Vacuum consumable www.easycompos...
Пікірлер: 84
@psarkleousi219429 күн бұрын
Ya...your carbon work is immaculate!
@Kalenth Жыл бұрын
I’m amazed that something with such precision can be made by hand. Incredible.
@Jeff_Rowley Жыл бұрын
Incredible. There's levels to everything. Your carbon work is pure art. They way you wove in multi directions was insane! Beautiful work 🔥🔥🙌🙌
Жыл бұрын
I came looking for regular Fliteboard tutorial then this... 🙌🙌🙌
@blakoemail2 жыл бұрын
The most beautiful carbon designs
@davisboring11116 ай бұрын
I would love to know where you sourced the battery, motor, esc from !!!
@odieostrich7718 Жыл бұрын
this could have gone wrong in so many ways... MAD respect
@mariusraupelis88962 жыл бұрын
Inspiring as always!
@tangomax_81882 жыл бұрын
Come sempre lavori sopraffini, impensabili da raggiungere per oggetti fatti in serie! Complimenti per la grandissima cura esecutiva e di progetto nonché la raffinatezza nelle scelte costruttive dei materiali ! Questo nuovo hydrofoil elettrico è una bella realizzazione con tanta funzionalità. Può anche essere un ottimo metodo propedeutico per apprendere gli equilibri dell'hydrofoil prima di passare al kite. Personalmente rimane superlativa la realizzazione del Box wing 2, forme eccellenti e concetti 👏 Con il doppio wing, a parità di alto AR, raddoppia la superfice totale e ne aumenta la resistenza a flessione per via della maggiore sezione geometrica. Saranno anche DIY ma sono opere d'arte della tecnologia!
@Brucecreations772 жыл бұрын
Grazie, troppo gentile. Il bello dei lavori artigiani' è che ti permettono di uscire dagli schemi. È pensiero libero, senza vincoli.
@Coach_Rolando Жыл бұрын
Impeccable amazing carbon fiber work...great Efoil too...but the craftsmanship on the carbon is an art on its own brother...I wish you could build a Fliteboard Efoil board for me...I have the fliteboarod Efoil but would love to have a custom board build by you. great job man
@stereothrilla8374 Жыл бұрын
And it’s just that easy folks!😂😂😂
@SammyHelsper Жыл бұрын
Looks fantastic. I do this all the time except my parts cost $$$ airplane parts. None of this is DIY🤣.... Between the molds and the process not including the tools. For an average Joe this would be a HUGE undertaking. The resin infusion helps make the entire process a bit easier.
@ugobert4909 Жыл бұрын
This is freakin Awesome!!!!!! Top notch job 👌
@radekgrabski34822 жыл бұрын
Amazing job!
@mystamo Жыл бұрын
Bruce! So I've got some twil carbon on the top of my board like yours.. I've done a split layup design .. I want to do one layer of twil on the bottom and then put one layer of the nice cool honeycomb arimid carbon that you also use on the bottom. But wondering how I can get nice clean lines and a proper split between the twil and the honeycomb.
@e-nalujetsurfboards32822 жыл бұрын
Amazing! Best i have ever see
@aedanosler35502 жыл бұрын
Wow, that is so beautiful, how did you Cool your batteries in the E foil, because the battery looks to be fairly large. And did it heat up a lot whilst you were using it. Your E foil is the coolest one I have ever seen
@Brucecreations772 жыл бұрын
Hi Aedan, thanks. I cooled only the ESC, the battery doesn't require cooling because is correctly dimensioned. I used the foil several times full throttle for more than an hour but never gets more than 40/45°C.
@Eden_M2 жыл бұрын
Such a talent, what type of wires are these? those phase wires with the white insulation, I couldn't find any info about those, mind sharing?
@Brucecreations772 жыл бұрын
Hi thanks! They are provided with the motor by FlyRodeo, I searched for them but I never find them. They are perfect for such this application because of they have a lot of copper in a thin section.
@wesnobles Жыл бұрын
That is gorgeous!
@PerWiklund234 Жыл бұрын
I looked to me like you just pressed together the mast moulds halves with epoxy+milled carbon or similar over the fabric. Is that correct? Or did you vacuum bag each half first? I have done some experiments with both. And also with epoxy+micro balloons. Always a bit afraid to get air pocket and dry spots without bagging. Any secret method you would like to share?
@Brucecreations77 Жыл бұрын
I simply wet-lay the two halves with carbon fiber until they are filled, I take care to remove the entrapped air, I put some extra resin in the middle and close and press the mold. For sure you'll have some little trapped air (very very few if you wet lay properly) but in a full carbon fiber mast it doesn't make any difference in terms of mechanical properties.
@PerWiklund234 Жыл бұрын
@@Brucecreations77 Thanks, I will give that a try.
@leonardonunes5501 Жыл бұрын
Impressionante seu trabalho. Parabéns. Ficaria feliz se você ensinasse a tecer o carbono unidirecional em um tecido tridimensional, como você fez. Faz um vídeo pra ensinar.
@leventyanar95292 жыл бұрын
Hi Bruce, which electric motor did you used. Would you mind to write down pls?
@mikimimi65982 жыл бұрын
Fantastic workmanship! How did you join top and bottom part of the board?
@Brucecreations772 жыл бұрын
I produced a profile that match the two half using one side of the mold and the model
@matthiasmeiffred60682 жыл бұрын
Hey ! Amazing job as usual on your channel. Will you present what you use in terms of motor and how it's waterproof in the nest part ? Thanks a lot.
@Brucecreations772 жыл бұрын
Hi Matthias, thanks, I used a Flying Rodeo motor, It is already filled with oil and there is a gasket on the shaft
@matthiasmeiffred60682 жыл бұрын
@@Brucecreations77 Thanks for your answer. Can't wait to see the next part !!
@giuseppecaranti91698 ай бұрын
ciao, bellissimo lavoro, complimenti! se ti facessi avere una sagoma in EPS riusciresti a farmi una tavola?
@Brucecreations777 ай бұрын
Ciao, mi spiace ma non ne ho prorpio il tempo.
@Indiana07 Жыл бұрын
Holy shit awesome work and detail
@thundercats4752 ай бұрын
wow what a craftsman...Change the title to how I make an eFoil, I don't think we can replicate you.
@Brucecreations772 ай бұрын
@@thundercats475 🤣🤣 it's only a question of patience..
@PerWiklund2342 жыл бұрын
Impressive!
@catalinstroe22 Жыл бұрын
damn! im inspired now!
@giuseppecaranti91698 ай бұрын
quanto pesa solo la tavola con il coperchio del case?
@Nodeagent2 жыл бұрын
Amazing! Btw, how does the box wing work?
@Brucecreations772 жыл бұрын
Hi, thanks. The box wing works in the same way as the Kitefoil version that I developed through the years. Compared with wings with a similar lift is faster and easy to handle, tight turn.
@fpxy002 жыл бұрын
Hi Bruce? Would you maybe sell CAD files?
@Brucecreations772 жыл бұрын
There are no cad files, it's all hand shaped. I did some simulations with the Wing just to choose the profile
@Felisargyle2 жыл бұрын
what the fuck you are so skilled...
@carbonarne6752 жыл бұрын
Creapy perfect
@Joole1000 Жыл бұрын
Damn, amazing!
@maca56452 жыл бұрын
Is the boxwing being developed into a commercial version?.
@Brucecreations772 жыл бұрын
the concept is proven but I'm working on fine-tuning.
@printrun5 Жыл бұрын
what is that green stuff you used for the mould?
@Brucecreations77 Жыл бұрын
It's a mould making material, you can see the reference in the description
@efoilDemis2 жыл бұрын
Ciao ammiro il tuo lavoro complimenti volevo chiederti il motore di questo video è lift ? Perché devo chiederti che tipo di esc utilizzi e se ci sono parametri da impostare all esc per non bruciare tutto
@Brucecreations772 жыл бұрын
Ciao, il motore è Flying rodeo e l'ESC è una trampa 75/300. Per le impostazioni è sufficiente usare il wizar.
@efoilDemis2 жыл бұрын
@@Brucecreations77 si ok ho comprato pure io un motore fly rodeo mi deve arrivare a giorni io utilizzo un altro esc della swordfish x 300A programmabile raffreddato ad acqua facendo girare l acqua come lift vediamo come gira
@efoilDemis2 жыл бұрын
@@Brucecreations77 ciao nel video non capisco come hai creato il pannelli di chiusura del vano , si vede due lastre di carbonio ma all interno come spessore che materiale utilizzi?
@Brucecreations772 жыл бұрын
@@efoilDemis Ho usato due fogli di www.easycomposites.eu/3d-core-infusion-foam-core, uno da 3 e uno da 5 mm. In un altra tavola sono andato diretto con il 10 mm. Con infusione viene un lavoro pulito, leggero e molto resistente.
@efoilDemis2 жыл бұрын
@@Brucecreations77 ok ma bisogna resinarlo tutto o basta incollarlo con due pannelli di carbonio rigido , perché ho paura che si flette io utilizzo il nido d ape alveolare in aramidica però se posso usare altri materiali meglio dimmi te se come utilizzare questo materiale io non l ho mai usato