This conveyor needed a few parts. So I took the liberty of making a few change's. Some metal parts and its a new machine. I created this video with the KZbin Video Editor ( / editor )
Пікірлер: 20
@pnwRC.5 жыл бұрын
Very nicely done! I've been looking at idea to use for conveyors around my RC Playground. I LOVE this idea so much, I'm stealing it to use in my playland!
@mclr.cfabricationandperfor52555 жыл бұрын
Anthony Kalnoski please do!!!! But note for best performance and results. Remanufacture the rollers to metal aluminum or brass. And use a 280 to 360 sized right angle gear motor instead of the servo.
@LetzinItaly3 жыл бұрын
Hi ! When you talk about 280 or 360 is rpm? And what is better? And the voltage of the motor ? The motor geared is 90 degrees? I write from Italy 🇮🇹 an my English is so so😁can you replay me please? Thanks 🙏
@rcconstructionincanada37545 жыл бұрын
sweet! I just modified my servo today. I am going to order one and hopefully have it for the weekend.
@RCP578 жыл бұрын
Very nice!
@RVJimD8 жыл бұрын
Nice! I like the side rails and the chains are a nice little detail. What about a slide gate on the hopper to adjust feed/flow rate? I might need to find one of these and do the same mods. Good job! Jim
@mclr.cfabricationandperfor52558 жыл бұрын
+RVJimD I will be making that mod adjustment thanks for the input.
@dustinpopovich6664 Жыл бұрын
can we have dimensions on sides at the loading point please
@EwertonMoreira807 жыл бұрын
How did you add the motors? I am trying to find a way to disassemble it but I did not figure out. The "snapping clips" seem to fragile. thanks
@mclr.cfabricationandperfor52557 жыл бұрын
Ewerton Moreira check out part 1 and you will see how. It shows what I used and how to motorize it.
@ivancatherwood91773 жыл бұрын
Im building one atm .. but with motor belt seems to stick etc.. any ideas?
@mclr.cfabricationandperfor52553 жыл бұрын
Sure tighten the belt. At the top of the conveyor you will see holes marked but no hole. Drill it out and move the roller up to the new holes made.
@umitkucuk93514 жыл бұрын
hi can you give me the bucket size?
@mclr.cfabricationandperfor52554 жыл бұрын
ümit küçük Bruder( Brother)track loader bucket.
@umitkucuk93514 жыл бұрын
Do you make a bulldozer on order? @@mclr.cfabricationandperfor5255
@Mr32Jacks4 жыл бұрын
How much do you charge with shipping to NC?
@mclr.cfabricationandperfor52554 жыл бұрын
caprice3230 gmail this is far to easy to make yourself than me building and shipping cost. It’s a Bruder conveyor from eBay or Amazon, and continuous rotation servo. Most of which you may already own. But if you would like a expert built conveyor there is a guy near you, check out smallhaul he is on KZbin. I think his conveyor is what your looking for. Look for his conveyor videos
@Mr32Jacks4 жыл бұрын
@@mclr.cfabricationandperfor5255 thanks for the info. I actually tried your part 1 myself. The servo grinded the plastic out.
@botrovvienski3230 Жыл бұрын
How much
@mclr.cfabricationandperfor5255 Жыл бұрын
Well I don’t sell them, I just make stuff for myself!