Bubble free jesmonite!!

Let me show you how you can learn to make jesmonite items with no bubbles!!
Hi, my name is Sys and Im the owner of Galleri Mindedahl.
I will let you in on all the secrets on jesmonite, ceramics and other techniques so you can skip the hard learning curve and get the job done!! ☺️🙏🏻
Please share, subscribe and comment💕

[@aquaandsage]

Wow👌🏼one of the very best videos on Jesmonite I’ve seen and I have watched literally 100’s. Thanks👏🏼👏🏼

[@Galleri-Mindedahl]

Thank you :-) I have noticed that each batch of jesmonite is different so sometimes bobbles are a huge problem, others its just fine. In general I don't use the 1x2,5 ratio ever. its too thick and hard to work with. I talked to the danish distributor and they agree that the quality for each batch they buy, vary in quality and its a problem. not sure what can be done about it.

[@FlorinGN]

It looks flawless! 😮

[@beatrizvalentinuzzi2456]

❤Perfect work! ❤️

[@mattersofthehartbynat8815]

Thank you so much for sharing your methods with us! ♥️♥️🇦🇺

[@EbmI013]

great video! thank you very much :) how do you clean your equipment after mixing the mass?

[@StevenfromTX]

I will definitely try the alcohol for bubbles! Thank you

[@Galleri-Mindedahl]

Let me know if it works out☺️

[@jitskelourens9906]

Do you leave the jesmonite resting for a while before pouring?

[@jays6032]

Hi. This video is brilliant. I have seen so many videos but nothing was this clear. I would like to know what sealers you use and how do you do it.❤

[@Galleri-Mindedahl]

Thank you so much🥰 I use the jesmonite acrylic sealer deluted in water 20-80 ratio. I dip the whole thing once sanded down but before it is dried. I wipe with a table cloth, let it sit for min and dip again. Dry off with table cloth. Let dry completely. No brush marks etc 😉 on items that need to hold water like soap dish I dip 3-5 times same procedure.

[@PA-rp8es]

❤😂🎉😊

[@alreemalsaif6083]

I usually have a white spots even if I mix it with mixer , what should I do ?

[@Galleri-Mindedahl]

I highly recommend using a jesmonite mixing blade and the full speed for couple of minutes. It will turn silky smooth I promise its worth the cost

[@traceysmartart]

Hi. How long do you leave it until you de-mould?

[@Galleri-Mindedahl]

Hi there. Depends on the outside temp, how much pigment I added and the quality of the jesmonite batch. But anything between 45-60 minutes ☺️

[@SafeHavens]

Det lyder rigtig godt med en anden ratio end 1:2,5 😘 Hvor meget ændrer det på arbejdstiden og hærdetiden ? Og er produktet ligeså stærkt som normalt ? På forhånd tak for svar 🥰

[@Galleri-Mindedahl]

Hejsa. Det har ingen betydning så længe du ikke demolder for tidligt. Det er lige så stærk som normalt og opfører sig ens. Jeg har ca 20 min til håndtering uden retarder

[@moodswing_poster_shop639]

1000 tak for instruktion, for en totalt nybegynder, kan du så forklare hvad det er jeg skal købe ? altså væske og pulver ...@@Galleri-Mindedahl

[@FurryFunniesTV]

Thank you for your great video, can I use a vibrator table to get rid of bubbles?

[@Galleri-Mindedahl]

Probably, i tried it but it didnt work for me