OMPHobby ZMO VTOL Debugging (trim settings)

[@dutchloveRC]

very cool !!

[@peteelab]

Well done!

[@BuddyRC]

Thank you stay tuned for more content

[@davidlee50]

Is there a repair shop at Buddy RC for this plane if we get it? Do you flash for buyers?

[@jaimehhrhr2853]

Que buen diseño. Que tal si cambian el modelo para que se parezca al Byraktar TB2, así el tercer motor podría girar también y pasar a ser carga útil?

[@BuddyRC]

Puede ser algo para el futuro

[@tumeeffimero189]

Great video. But now I have this problem: i can control the motor angle setting (drone mode) only for the right motor (aileron) and in airplane mode i can control only the left motor (rudder). For aileron no problem. For elevator the right elevator is ok for the left I have to set the throttle all the way up and than I can control with the rudder. At this point is not safe to fly… . It’s possible to reset the FC (or to flash the firmware)?

[@BuddyRC]

Hello there no way to access the FCs firmware but please write us an email at [e-mail]

[@dkieng]

Can you show where to solder the TBS Crossfire RX to on the FC?

[@BuddyRC]

It's a 4 pin connector

[@واحةالعلوم]

Hello, is there a way to do a factory reset for the autopilot of the zmo?

[@BuddyRC]

no

[@upperechelon3456]

Great video Eddie. Question: In doing the motor angle trims is there a analog reading setting from say 0-180 degrees to help in precisely setting the motor angles. Seems like just eye balling it is not very precise. Not an issue with the control surfaces though. Just asking Thanks

[@BuddyRC]

90 degrees to the wing in VTOL mode but this video is for everyone and most don't have a pitch gauge. The flight controller does most of the work.

[@PhilippTrost]

In VTOL Mode if i yaw to the left only the right motor is moving forward. If i yaw to the right the left motor is moving forward and the right a bit backwards. Should it be that way :D?

[@BuddyRC]

Watch our video on debugging mode

[@marcelovagula4312]

What controller is used on this drone? Ex.: Pixhawk, Matek ???

[@BuddyRC]

Any controller you would like

[@jayss1966]

Do I have to use a DJI air unit? Can I use a standard vtx with a runcam and still get telemetry on OSD?

[@BuddyRC]

Yes

[@motisarid]

If I use DJi TX witch rx I have to use

[@BuddyRC]

The receiver is built into the Caddx Air Unit

[@Doughboy-be6ie]

Is this drone good for flying in mountain ranges places that have bad GPS and satellite connections? If not where do I buy one?

[@BuddyRC]

The link is in the description where you can purchase and you should not have any problems with GPS connection

[@LoneStarUAV]

What channel do you assign the switch SD to? 5 or 8?

[@ristokoiva]

According to Oscar Liang, SD is by default mapped to Ch8 on DJI: oscarliang.com/dji-fpv-system-setup/ (SA = Ch5, SB = Ch6, SC = Ch7)

[@Yaito21]

What is the cost

[@BuddyRC]

www.buddyrc.com/collections/fpv-plane/products/hee-wing-t-1-ranger-730mm-wingspan-dual-motor-epp-fpv-racer-rc-airplane-fixed-wing-kit-pnp-gray

[@driftx2]

id stick with 1 propeller

[@BuddyRC]

It's not for everyone

[@jeffcollins7055]

Pᵣₒmₒˢᵐ ?

[@BuddyRC]

Can't understand