Budget bending for all your Tube projects.

[@davidmorgan8612]

I’m glad you are throwing a fresh coat of paint on there and not an old coat.

[@JeepingMo]

I would like to invest in to a better bender, at this point there isn’t the work for it. Thanks for viewing.

[@davidmorgan8612]

@@JeepingMo I’m in the same boat.

[@matthewmoilanen787]

Oh yay another unboxing vid!

[@westweld]

Thats a pretty sweet little set up

[@JeepingMo]

Thanks.

[@totonaf]

Many thanks for your video znd for the link. Very useful video

[@tarbeau8561]

Thanks for sharing this video, enjoyed watching thanks again

[@JeepingMo]

Glad you enjoyed it, thanks for viewing

[@akbychoice]

Very good information.

[@JeepingMo]

Thanks. Im glad you enjoyed the video.

[@mattcalder3602]

Did you get the die from a different company and if so where at?

[@JeepingMo]

@@mattcalder3602 they are woodword fab

[@600miles]

Does it use JD2 dies? Unit looks just like my JD2 Model 3

[@JeepingMo]

Thanks for viewing, no the JD2 dies are different than everything.

[@michealfigueroa6325]

TY 4sharing it was helpful

[@JeepingMo]

Glad it helped. Thanks for the comment.

[@shevilihabibi8895]

please tell me, what pressure does your air compressor create for this cylinder?

[@JeepingMo]

I run my compressor at 100 psi thanks for viewing the channel.

[@shevilihabibi8895]

@@JeepingMo thank you sir!

[@manuelgrospe9181]

I need this

[@jss6060]

How do you know how much fluid to add to the Ram? I’m having issues with my new setup

[@4x4fabshop]

with the cylinder all the way back, i filled it to the top. thanks for the question. let me know if this helps.

[@jss6060]

@@4x4fabshop do you fill it when it’s vertical or horizontal?

[@4x4fabshop]

@@jss6060 i did it horizontally.

[@jss6060]

@@4x4fabshop thanks for the info and the fast reply. I’ll try it out

[@4x4fabshop]

@@jss6060 what position is the air system.

[@BigDave71]

Very nice tutorial but I’m not quite sure about that pointer. Thanks again by the way.

[@JeepingMo]

Yeah, the pointer is not the greatest. I need to change that but thanks for your comment. I hope you like the rest of the Contant on a channel. Thanks for viewing.

[@TheBeardedJeeper]

nice setup how much did that whole setup end up costing you?

[@JeepingMo]

It was around $650. The die is almost as much as the bender. If you can find a used die you really save some money. Thanks for the comments and viewing.

[@TheBeardedJeeper]

@@JeepingMo you bet. I’ll need a die eventually. Thought I was subscribed but wasn’t. I am now.

[@JeepingMo]

Keep an eye at harbor freight for open box sales. We found the cylinder for $60. Normally over $100

[@JeepingMo]

We started a Fabrication only channel , we would appreciate if you checked it out and if you like it please subscribe. Here is the link kzbin.info/door/ymCioKuGeACQLff-gRyKnA

[@makingcookingfixing]

@@JeepingMo now its more like $850

[@MisterDivineAdVenture]

Looks like a two-barstools situation there.

[@totonaf]

There is no link to the product !

[@JeepingMo]

I put some in there now. Thanks

[@jimmoravec1326]

That 90* bend looks pretty flat

[@tiger09298]

좋아요

[@JeepingMo]

Thank you