How to Build A 2 Cylinder Inline Two-stroke Engine using 2-stroke Engine at home Thanks for watching, Have a great day !
Пікірлер: 1 300
@BlusEXE3 жыл бұрын
The fact that this lad just has a pile of 2 strokes lying around makes me sooo jealous. Keep up the great work!
@catman46443 жыл бұрын
Lad? This appears to be a LASS, which makes it all the more remarkable!
@frankw83153 жыл бұрын
ikr
@frankw83153 жыл бұрын
@@catman4644 it’s a lad
@tandmbros58773 жыл бұрын
My freind here in america has a pile of two strokes... you can find free weed whackers a dime a dozen out here
@wompstopm1232 жыл бұрын
@@catman4644 hes a lad, the long nail on 1 finger is for doing cocaine
@jacketspritecranberry48763 жыл бұрын
You need to time the engines correctly one engine with the piston at the top, and one at the bottom, and make sure the idles are at the exact same rpm. Notice how there’s only smoke coming out of one of the engines. There’s air coming out of both because of compression, not because their both running
@acoder9123 жыл бұрын
my thoughts exactly, the idea is good but i not sure its actually running on two , is it 360 or 180 degree timing? interesting idea for a four cylinder.
@jacketspritecranberry48763 жыл бұрын
@@acoder912 it would probably be 180 degree timing
@jacketspritecranberry48763 жыл бұрын
@Jade Spale 180 would be ideal because when one engine is at the exhaust stroke, the other would be in the combustion stroke. 180 degree timing would have the best affect on power for a two stroke, I feel 360 degree timing would be best for a four stroke
Actually, you dont "need" one at the top, and one at the bottom, since they both have 1 ignition coil per cylinder, they are both individually timed. (Unless he is using 1 coil to fire both cylinders, then timing could be off) Look at all v twin motors, they are not one up and one down. Id dare say since we seen it had spark on both cylinders, that it must be a fuel delivery issue on the "non smokey" side.
@buzzsawncgo27513 жыл бұрын
I had a motorcycle that was made almost exactly like that back in the mid 1970's. It was a 500cc Yankee. The engine was made with two 250 cc Ossa barrels mated on a common crank shaft. When the folks at Yankee were initially considering the splice, they tried the engine with the pistons firing on opposite strokes so that power was continuous but found that the bike (which was intended for enduros) had a more useful power band with them mated on the same stroke. The power was like that of a 500cc single. They called it a twingle, or at least the riders did. It was massive in the woods. If you had the alternate stroke config. it just spun the tire and the power didn't get to the ground. Wish that I never had let it go.
@davidelliott58433 жыл бұрын
Before WW2 there was a genuine Twingle aka split single. Two con rods with offset crank pins two cylinders pumping one cylinder head. One on inlet side and one on exhaust. It gave a longer dwell time at TDC but poor gas flow meant no overall advantage. . kzbin.info/www/bejne/aaK6p59vdruZl6M
@davidwillard73343 жыл бұрын
CHAINSAW !! WOULD BE ! GOOD !! FROM IT !!
@Backwoods-Bob4 жыл бұрын
Reminds me of Garage 54 putting two 4 cylinder engines together, and running them in a Lada(?).
@aliciaantoniadis91003 жыл бұрын
Yes!! I saw that one and I liked it very much! Thank you for this comment.
@szypki_zygi3 жыл бұрын
They did 4 of them later down the line XD
@BotijoRural3 жыл бұрын
Yes, in a lada. Garage54 rules
@beeftec58623 жыл бұрын
Garage54 werent stupid enough to call it a V8 though
@borivojetravica5693 жыл бұрын
Giv us the link!
@phoenixme743 жыл бұрын
Now you have two engines that will be a pain in the ass to start each spring 😁👌
@nicholasgaudet63093 жыл бұрын
Hands down the coolest thing i've ever seen anyone do with a couple 2 stroke engines.
@kimkeam20943 жыл бұрын
Interesting build, and very informative. Two things that stand out. A carburettor balancer is required otherwise idle will never be stable or you can accidentally run one lean at operating revs, ruining that cylinder. Secondly, cooling is now missing on the number two engine as the fan shroud was removed and no metalwork to guide the airflow from the front engine, or the machined impeller to even slightly reduce cylinder head temperatures. I guess it is a work in progress. Perhaps fitting a multi blade shrouded propeller on the drive shaft, with adequate baffling ,would be able to draw the air past the cylinder and vent it away from the engine.
@joerolfe79673 жыл бұрын
Even though this is a twin engine setup and not twin cylinder, its still very cool and man it sounds way cooler then i would have expected. Nicely done.
@joeMW2843 жыл бұрын
Pretty cool. I think the cylinder without the pull start would be in danger of overheating if you did any real work with it though. And like others said, putting the two cylinders 180 degrees out would prevent the assembly from rattling apart.
@jasonb43503 жыл бұрын
Right engine is not running but still shows the paper moving because of compression escaping through the exhaust and I say this because there was zero smoke coming from the right engine.
@JonBecker813 жыл бұрын
It was running. He adjusted the idle on it and it sped up and slowed down.
@Alex-qb1kp3 жыл бұрын
12:58 you can see smoke
@repsaii38553 жыл бұрын
Hell yes it was. Look at 13:05 there you can see the smoke
@bagusreformasi69113 жыл бұрын
@@Alex-qb1kp ................... 53
@timwever67933 жыл бұрын
both running but fist one hase more takeouts than it actuell runs. wrong timing
@nathaniellangston51304 жыл бұрын
It's pretty cool how you connected the two engines! I wouldn't have thought to do it that way!
@mateuszdobija29614 жыл бұрын
the first engine must be in TDC second engine must be in Bottom Dead Center, engines must be synchronized, when first make the power stroke the second must make the compression stroke.
@kcpilot214 жыл бұрын
I was thinking the same thing. Engine and spark timing.
@santiagoperez20944 жыл бұрын
That would be the best choice to smooth torque, but isnt necessary at all.
@yudiwahyudin66444 жыл бұрын
Maybe 270° sound better. 😁
@Gamer-nc8qp4 жыл бұрын
this yes
@dieselgeezer184 жыл бұрын
the timing is not great. But it doesn't need perfect timing to work. There are many types of engines with some weird timing
@JohnJaggerJack4 жыл бұрын
Now do that until you have an inline 8 cylinder two-stroke engine, and put it in the kart.
@yoellobi4 жыл бұрын
jajajaa
@Bizones164 жыл бұрын
Why Stop there ? ! Get 6 or 8 V-Twin 4 Stroke engines and mate them ALL together for a V12 or V16. THEN we can have some FUN !
@Bizones164 жыл бұрын
I forgot in my previous reply, run them in a FLAT PLAIN CRANK configuration.
@bubgyu39614 жыл бұрын
What about V or F
@marcw26043 жыл бұрын
@@Bizones16 or opposed twin air cooled in to a boxer 4 or 6 ect
@oscaruiz80554 жыл бұрын
those two motors have a beautiful sound when working together congratulations great idea (I'm already anxious to see what you plan to use it on)
@bryanduncan16407 ай бұрын
How “lucky” to have a pile of perfectly sound engines in a heap at your disposal? Who could have guessed?
@John_Makes4 жыл бұрын
Nice work I'm doing the same thing with 2 pocketbike engines but i used cam sprockets and a timingbelt to join the two engines! Runs great but i will change it to a 1 carb instead of 2
@jeeper4263 жыл бұрын
i dont know why i'm imagining this on a weedeater now, cool build
@neko76843 жыл бұрын
literally same
@justin4563 жыл бұрын
Moar power babeh
@lukimyu13 жыл бұрын
I have been looking for something like this for ages!!!
@james86603 жыл бұрын
That coupling you made is pretty smart, avoids the alignment issue if you wanted to hard mount it together I guess!
@pedrohenriquecordeiro39542 жыл бұрын
😰😵😤😣🌞☁
@youtube.youtube.013 жыл бұрын
Very ingenious! Creative crankshaft coupling is an interesting challenge to watch other people solve!
@garymucher95904 жыл бұрын
Rear or second engine looks like it is running richer then the first. Since both are supplied via one tank, you may want to richen up the first engine some to keep from heating up... But very interesting build all the same.
@johnblack79433 жыл бұрын
I was just saying he should just make a manifold and use one carburettor for both
@user-kn5ol8ck8s3 жыл бұрын
dual carbs are actually better but you have to have them adjusted exactly the same. Take them both apart and rebuild them both the same with the same adjustments.
@pauls57453 жыл бұрын
I think I'd try to make a custom dual intake for a single, bigger carb and try to make 2 expansion exhausts. then drop it in a motorized bicycle I'd love to see more people do things with this!!
@charliebrown2382 жыл бұрын
That would most definitely make starting, and tuning a hell of alot more easy. Although the twins would make higher hp overall, i think the tuning and syncing would out way the power increase for drivability and ease of everything
@SteelCityRC3 жыл бұрын
Very inventive work. Would be nice to have that lathe. Twin 2 strokes sound so mean. Two Walbro carbs and steel tuned pipes is the ticket. Nice work on this one!!
@JoshPhoenix112 жыл бұрын
I've always wanted to see a 2 stroke radial engine made with these
@firerejack11213 жыл бұрын
Make a v8 engine with just these little strimmer engines that would be amazing 😂
@Sauron_Green3 жыл бұрын
I've seen these motors used in 2-stroke friction drive motorizing kits. Note that I mean the single cylinder not the custom twin cylinder you've made. Also, it would be amazing seeing put into action as a custom motorizing kit for pretty much any driveable platform.
@MrThunderCunt Жыл бұрын
Im currently build a performance engine woth one of these. I ported it and polished the exhaust, bigger carburetor, and a home made bracket to move the coil and change ignition timing. Also have made my own exhaust for the project im using it for, which is a full suspension mountain bike. Im modifying the suspension of the mointaim bike aswell to get more travel. Also adding some fender and stuff so it will basically be a dirtbike. Im also figuring out a way to use the stock shifter mechanism to shift it. Maybe maje it a 3 speed, but idk yet.
@john76304 ай бұрын
Where is time belt?
@Undertaker1134Tx Жыл бұрын
Love the build. Did the same to rc nitro motors though I've been wanting to build one of these to make a custom moped a duel 25cc in a alt fireing flat config. The carbs are not synced, mark the output crank to read rpm, unplug 1 sparkplug@ a time to adjust each running side to match idle rpm.
@darinmckillop61963 жыл бұрын
Very creative I been a small engine mechanic for 40 years and this is good.prob just double fire cute.it would be neat to dino 1 and the other to see if there's much of a difference Great prototype for something better good luck
@jackshadowblades29573 жыл бұрын
This is cool thanks for posting it. I'm gonna try building one and installing it in an old pedal cart tractor
@parkersposts3 жыл бұрын
Please post a video of it if it works it might do wheelies!
@White_Night_Demon2 жыл бұрын
so how did it go?
@dimavieru89994 жыл бұрын
great job man, can you built an inline 4 6 8 10? i guess be amazing to put it in to a bike like kawasaki 6 cilinder
@philippwetter4 жыл бұрын
Next you should do a inline 3 with a 120 Deg crank offset, would sound sick!
@bsracer853 жыл бұрын
I have to ask? How can there be 1 thousand people that do not like this video. GREAT IDEA
@manuelbertram87853 жыл бұрын
Do they ignition at the same time or did you mount them 180° apart?
@Chuffin_ell3 жыл бұрын
A collaboration between this channel and “the practical channel” would also be very interesting...
@beeftec58623 жыл бұрын
Even more so with "the accurate thumbnail description channel"
@OpitiumThirtyTwoIncOTTI2 жыл бұрын
seeing this engine mounted and running would be awesome 👍🏻
@braydenbratcher37303 жыл бұрын
These are the kind of videos I’ll I like people working on engines and putting and making odd things with the coolest machinery
@BlusEXE3 жыл бұрын
I can only WISH I just had a pile of engines lying around.
@jackstrempel51353 жыл бұрын
I got a pile of blown up race car engines in my shop
@dennism6443 жыл бұрын
Should try and hook a chain bar to that set up for a twin cylinder chain saw
@mycoboto3 жыл бұрын
Twin cylinder chain saw eh? Now i can manscape with confidence!
@dydy715803 жыл бұрын
Twin cylinder chainsaw exist : Echo cst610evl and solo
@davidwillard73343 жыл бұрын
ECHO !! Had a Twin Cylinder !! Saw !! Back in the Eighties !! In there Catalogue!!
@FIXDIY4 жыл бұрын
It is a mental activity characterized by departing from customary thinking and producing creative ideas
@gtgodbear63203 жыл бұрын
My uncle built my cousin a go-kart with 2 47cc two stroke engines. Both cylinders would fire at the same time. It felt way faster than it should've been.
@quentin80943 жыл бұрын
“For the toughest of weeds”
@davidwillard73343 жыл бұрын
WHAT !!?? FOREST !! TREES !!?? MAYBE!! ROCKS !! TOO !!!
@maybejapheth3 жыл бұрын
Underrated 😂
@saharut45133 жыл бұрын
I want to see 4 stroke engine like this ++
@stevemartin77213 жыл бұрын
That'd be a potent little engine for a kids cart...thanks for posting.
@slicaltimistic13 жыл бұрын
😁😁😁Alright. Let's put that twin 2 stroke on a bicycle, or scooter and let's see some numbers next. And do a 12 cylinder 2 stroke. This I got to see.👏🏼👏🏼👏🏼
@tomasrous73244 жыл бұрын
It looks like only one is firing, bcs there is no smoke coming from one
@ondrejfusek90044 жыл бұрын
Čech? 😁
@mr.engineear09874 жыл бұрын
Yeah so, it is still firing with very low amount of smoke coming out on the second cylinder
@mr.engineear09874 жыл бұрын
Anyway you can see smoke coming out both at 12:58
@crudboy124 жыл бұрын
It's obvious that both are firing. You can see smoke coming out of both at all times. It wouldn't run properly if only 1 was firing anyway.
@hkmusicfactory74804 жыл бұрын
kaise ho bhaiyo
@Rudofaux3 жыл бұрын
Won't take long for that rear unit to overheat. The flywheel's fins were cut down reducing airflow & no shroud to redirect said airflow. No airflow, no cooling. Nice little project thou.
@Hellsong893 жыл бұрын
Custom shroud to go over all of them and make first one have actual fan blowing trough the setup.
@ostolski3 жыл бұрын
that's the first thing I thought too and it's not practical unless you rotate the cylinders 90° and blow the heat to the side and install a shroud on the second motor at least the block the heat from blowing on it from the first one
@jaymesc.moreland92653 жыл бұрын
@@ostolski A decent fan and baffle setup could still blow enough air to cool the rear cylinder without staggering them. Small aircraft such as the Cessna 172 do it all the time with 2 or 3 cylinders in a row.
@Twin_Flyer3 жыл бұрын
Interesting build! Need to find it a home now. Where did you get the fuel fitting for the tank you modified? i need one for a project!
@roiedavid38304 жыл бұрын
I wish i could have that for my proj to my scooter, watching here from the ph
@chrislaz24734 жыл бұрын
What's the parallel twin gonna be used for? Bad ass weed whacker?
@FirdausIdros3 жыл бұрын
yes and drone engine too!
@Rudofaux3 жыл бұрын
@@FirdausIdros Engine is too heavy for drone usage. Sure the power to weight ratio is there, however you're forgetting the propellers would need to be substantial to lift just the weight alone not including the drone's own frame work.
@wildcoyote343 жыл бұрын
@Rudofaux the drone engine idea is a good one but i would use a 1 cylinder engine and a generator to increase the flying time of the drone ,,I built a prototype of my own with a 38CC chainsaw engine about 2.5HP,it generates 12.5 amps at 36V ,,the entire assembly weighing just over 8 pounds including the rectifier and regulator controller ,,it was installed in a 4ft Octo-copter drone and was able to fly for 83 minutes nonstop powered by the generator alone before a rectifier burned out I have also experimented with building an engine powered drone ,this was a mixed success because while this machine which weighed near 20 pounds had excellent lifting power it didn't have the control of an electric drone .totally mechanical driven the control was accomplished by literally swiveling the arms with the propellers ,,,and finding gearboxes capable of the RPM and loads necessary for this was quite easy ,,,literally ANY strait shafted weed trimmer has a gearbox capable of handling continuous 9000 rpm operation
@banana_beard88713 жыл бұрын
He could use it for a gas powered Bicycle. Kinda like those kits but better.
@joeMW2843 жыл бұрын
yeah, you could do a bike.. rack mount on the back would probably be the best way. This motor is pretty long.
@oppaiwarrior10154 жыл бұрын
Thats twin 2 stroke engine , should be powerfull if you using those engine to make RC car (remote control ) car 💪💪💪
@vampiregirl324 жыл бұрын
😍💯💯💯💯💯💯 for off-road RC that will be epic 💯💯😍💯😍
@rebelforce49654 жыл бұрын
Monster truck or Buggy. 🤩🤩 Yeah that would be awesome
@lowellmunz3 жыл бұрын
Great skill! All my respect. 🙌
@alexsz.65302 жыл бұрын
Lets make more two , im so inspired to watch inline four cylinders with this 2stroke 💪🤣
@arisz21914 жыл бұрын
It's dual in-line cylinder, NOT V engine
@ChannelCreativeVN4 жыл бұрын
thank bro
@niel673544 жыл бұрын
If the crank is joint at the right offset it will sound like a V.
@arisz21914 жыл бұрын
@@niel67354 make it 270 degrees
@guanovolante78334 жыл бұрын
@@niel67354 but it is not a "V" shape, so it is not a V2
@elianedapenha13174 жыл бұрын
@@ChannelCreativeVN teaches you how to make an ulv cold fogger
@quintenvekemans94934 жыл бұрын
@4:08minutes those are some badass safety shoes 😂
@aidanlast86233 жыл бұрын
Quinten Vekemans Japanese work boots
@davidwillard73343 жыл бұрын
I !! HEAR !! THAT !! THEY !! ARE !! QUITE !! GOOD !! AND !! THERAPEUTIC !! FOR !! ARC !! WELDING !! TOO !!!
@gidasranau2283 жыл бұрын
I am watching from Northern Borneo Island..
@edilbertomarmol33953 жыл бұрын
Very good
@repalmore3 жыл бұрын
This would be a fun project for an RC airplane. Maybe a cowling to help with cooling or something like that.
@davethewaffler23364 жыл бұрын
You should try and make a an inline 4 cylinder
@jirirybacek54884 жыл бұрын
What about 6 😅
@themagicphoneboothq45293 жыл бұрын
V8 or nothin
@Rudofaux3 жыл бұрын
@@themagicphoneboothq4529 (laughing in rotary)
@appelmelk56643 жыл бұрын
Just keep adding till you have a straight 16 or something
@donaldshimkus5393 жыл бұрын
Hasn't anyone seen the FrankenBriggs ?
@Prosto16Simvolov4 жыл бұрын
А бумажка возле выхлопа принудительно вращающегося двигателя это показатель его работы? На видео видна работа одного двигателя. Синхронизация двигателей одной только отвёрткой не выполняется.
@Zdobik4 жыл бұрын
Я тоже про это видно по выхлопным газом что первый в холостую а второй в напряг.
Such a fun project!! Did the flywheel magnets/crank get offset, or are both cylinders firing at the same time?
@premjitsingh364 жыл бұрын
Only one cylinder is firing not the second he shows with plastic paper that both are firing but only one as smoke is coming from only single as it's 2 stroke engine both should show smoke
@kgb52234 жыл бұрын
No, both cylinders are firing, you can clearly hear it. It must be a carburetor tune issue, the one cylinder that's not smoking might be running a bit lean... Or the one that's smoking might be running a bit rich. Sometimes two stroke engines don't emit that much smoke.
@ukutominga45044 жыл бұрын
ideally, none of them should have visible smoke coming out
@Sebi076 Жыл бұрын
Bad english you have yes
@dustinmiller727811 ай бұрын
@@ukutominga4504 if you don't have visible smoke coming out of a 2-stroke you're running it too lean and you'll blow the motor
@badblenderanimations14497 ай бұрын
@@kgb5223he's right, I have a two-stroke motohoe and it only smokes when the engine is really cold or when I can't start it first try. It can also depend in the oil you are using...
@hitman66474 жыл бұрын
Love From South IND♥️
@friscoHub4153 жыл бұрын
Love the pinky nail I been rockin one forever
@HolzDennis3 жыл бұрын
I need one of this beast for my Chainsaw 👍🏻
@huntergrissett66973 жыл бұрын
This needs to go on a scooter or a motorcycle 😂 I gotta see it in action
@billbaden7423 жыл бұрын
How are you going to get airflow across the second cylinder
@lelandharper20993 жыл бұрын
BrickyBoi no, he means cooling. Air cooled engines don’t cool well with no air being blown across them lol
@thomasteichert87373 жыл бұрын
I need two of them for my bike! :DDD Great job!
@michaelrobertson87953 жыл бұрын
That'd be pretty cool to put that in a remote control deep V boat.👍
@billthetaxman893 жыл бұрын
"let's learn something" channel should collab with you...
@crazycreation69924 жыл бұрын
Can you make a rc boat with this engine..
@zacharykosinski28834 жыл бұрын
Engine is too big
@eloxdgg4 жыл бұрын
Yea
@FM602603 жыл бұрын
@@zacharykosinski2883 Why not put it in a bigger boat?
@zacharykosinski28833 жыл бұрын
Volvo B10M true but that would have to be a really big boat. So maybe that is a good idea it right
@BorosTheGamer50213 жыл бұрын
i wish i had something like that for a motorized project
@michaeldunagan78383 жыл бұрын
Genius! So cool! All without blueprints as well. So much for the theory that crankshafts need to be balanced. I guess it is not critical in 2-strokes as it is in 4-strokes.
@maxbetbrawn66634 жыл бұрын
Интересно для чего он поженил двадвигла? Рядом на столе редуктор лежал! Ждём-с короче!
@bagaboo37364 жыл бұрын
CoглaceH
@AlexMoonXXI4 жыл бұрын
Судя по другим видосам автора - он любитель мопедов, картинга, багги и прочих мототележек...
@Krasnov_Misha4 жыл бұрын
@@AlexMoonXXI какой нибудь веломопед может будет
@AlexMoonXXI4 жыл бұрын
@@Krasnov_Misha А я сначала думал - какой-нить индонезиец мастерит себе лодочный мотор. У них дофига типа байдарок с моторами от бензопил или газонокосилок. Такая длинная труба, на одном конце винт, а на другом - мотор.
@Krasnov_Misha4 жыл бұрын
@@AlexMoonXXI будем следить
@TechKnowCSS3 жыл бұрын
VERY COOL, NOW ADD ONE MORE TO MAKE IT A 3 Cylinder, NOW THAT WILL REALLY BE COOL AND SOUND GREAT AS A CHORD SOUND.
@White_Night_Demon2 жыл бұрын
so to make this you need a lathe, a grinder, a drill press, some spare pieces of metal, a hand drill, vice grips, two working 2 stroke engines, nuts, bolts a spanner for nut and bolt, piece of paper for template, a lever saw, some drill bits, silicone glue, sockets, a metal rod for custom spacers, some solder, soldering station, heatshrink, fuel, a switch, steel wire, and probably a month of time to get this all sorted out.
@user-ly6fl4ve7w4 жыл бұрын
It's interessant. Well done!
@papapaniop4 жыл бұрын
No its not interesant
@douro204 жыл бұрын
Anyone know how good those engines are? They remind me a bit of old Echos.
@enriquecuellomartinez96223 жыл бұрын
Muy bien el trabajo.. Pero a mi parecer solo hay uno de los motores encendido... Por la razón k solo uno está husmeando 😕
@dustinbowser27623 жыл бұрын
Enrique Cuello M
@AldreenEllohin3 жыл бұрын
I'm looking forward to seeing where this engine is going to go !!! o/
@victoryfirst28784 жыл бұрын
I really like the collection of engines you have Sir. Nice work too. VF
@user-mw4gx5kf7j3 жыл бұрын
А чё с первого горшка не дымит, а дует? Может он просто нагрузка?
@user-kj7xt8jm1o3 жыл бұрын
А вто это вот защем? Я просто по ихнему не шарю . Что с ней дальше то делать?
@MOTOPEMOHT683 жыл бұрын
Смесь беднит на первом.
@JohnnyEST13 жыл бұрын
What about cooling of the second cylinder? There is no fins and a cowling to aid cooling
@Kydenius3 жыл бұрын
Could you make a 4-stroke inline 2 motor like this and show us how to put it in a bicycle? Thank you!
@bradenwestfall50523 жыл бұрын
It already technically is an inline 2
@tc12543 жыл бұрын
Look up Zeda motor sports they made a twin engine 2 stroke on a bike
La verdad amigo desde que sigo tu canal me ayudado para algunas ideas... en verdad muchas gracias por compartir sigue así... ya he hecho algunos de tus proyectos y en verdad no sabes cómo me han ayudado.... saludos desde cancun Quintana roo México.
@RBAERO3 жыл бұрын
Very nice!!! Question both piston explode at same time or is one at the time? How do you set this timing?
@rayscyclesrepairs35163 жыл бұрын
“Sounds like it’s running on One cylinder” 😂😂
@Optimuseq3 жыл бұрын
And even looks like 🧐
@nainon38423 жыл бұрын
Yea its only running on one cylinder😂😂
@thomasrankl80113 жыл бұрын
i think so too - the ignition is the problem
@Optimuseq3 жыл бұрын
@@thomasrankl8011 whole project is done with many issues. Spark timing, cooling of the second cylinder....
@marlobreding74023 жыл бұрын
In the 70s we had 2 strokes called Twingles, both pistons were on the same phase of the stroke. The fired together
@srcarlosvaquera3 жыл бұрын
Try to do an engine "V" from 2 motorcycle engines
@chadscott24993 жыл бұрын
I meant to send that to some Yahoo
@joeynodz1483 жыл бұрын
Weld up some custom pipes this is really kool
@baimrider52613 жыл бұрын
ilmu nya boleh di coba,, salam dari indonesia bang
@skynjaydensdaddy3 жыл бұрын
Last time I checked inline isn't considered a "V"
@deborahchesser73753 жыл бұрын
Al H they got us watching though didn’t they
@Studdfromhell3 жыл бұрын
Still cool tho
@briancamp82613 жыл бұрын
All I can say is that my friend that is one hell of a weed eater
@holgers52163 жыл бұрын
LOVE the safety boots!! LOL!...needs twin SU carbs!!!!
@2Atreehugger3 жыл бұрын
Who the heck would give this a thumbs down.
@tunuk_kg69734 жыл бұрын
Мне кажется один движок не работает? Тот который не дымится при нажатии на газ 🤔🤔🤔
@arturatsaev34124 жыл бұрын
100 % не работает, 2 двигатель вращает первый и с выхлопа выходит давление!
@tunuk_kg69734 жыл бұрын
@@arturatsaev3412 Да темболе туда добавляют масло, дожноже дымет при газовани, по любому а второй выполняет роль компрессора
@user-ju8qu9gc6v3 жыл бұрын
У меня триммер не дымит. Развожу "лукойл мото2" и "штиль 2т", 20мл/литр. Триммер "champion" T27. Не факт что двигатель будет дымить. Это вам не планета и не восход. Ещё не меньше от износа цпг и настроек карбюратора зависит.
@filyamatross41003 жыл бұрын
@@user-ju8qu9gc6v зависит от положения дозатора в игле, а не от фирмы двигателя. На видео второй беднит, первый богатит
@c9rpses4 жыл бұрын
you're bored in quarantine right? XD
@hkmusicfactory74804 жыл бұрын
hii
@kingyamaha96373 жыл бұрын
Go inline 3 or 4 that would be very impressive and first ever on KZbin
@harionojhon95282 жыл бұрын
begini yg q suka ilmu yg bermanfaat dan mudah d fahami
@EdwardMurray064 жыл бұрын
Strangely, I love and hate that music in the background.
@hanterboos3443 жыл бұрын
What is the name of Music At minute 6:40?
@user-ep6cq4tv2w4 жыл бұрын
Привет, сделай мот с этим двигателем
@RoadXproductions2 жыл бұрын
2 2 strokes have never sounded so good together
@aliciaantoniadis91003 жыл бұрын
As always, very well done. Be well, and thank you.