BUILD CHEAP BELT GRINDER

[@antoniodeoliveira1849]

Thanks for giving measurements for those following your video makes things a lot easier

[@avizomedeo5178]

Thank you for the computer graphics. Makes understanding easier!

[@user-davidben]

נהדר עבודה טובה..אתה איש מוכשר..כל הכבוד..

[@klave8511]

When welding something with bearings, don’t let the weld current flow through the bearings. Connect the ground clamp to the same piece you are welding or the bearings get damaged.

[@jhonarief]

Thanks for this nice info, will note that for next weld project 👍

[@AubMar]

I was just about to say exactly that because the current will arc and pit the surfaces, and fail prematurely. I know because it happened to me once upon a time!

[@martyalcorn8990]

good to get a few measurements thanks, vital to know the belt size please

[@eddiewalker4530]

Nice work, great video and graphics

[@brucewaynehdl6388]

Excelente trabajo te felicito 👍👏👏👏

[@anglerweekenderrizalzi3419]

nice share and tutorial, thank you

[@martyalcorn8990]

thanks for the dimensions

[@woodstory1771]

Lagi dan lagi... Kayaknya uda lumayan banyak ni fans luar nya

[@jhonarief]

Berkat semangat sama doa om, ayooo om juga bisa... Yg penting semangatnya jangan kendor, kan udah ada laptop pendukung nih, semangat ya om

[@woodstory1771]

@@jhonarief Siap Om tx Support nya

[@restorationfr2098]

good job

[@nissanzargari]

Very nice job ,weldone from israel

[@jhonarief]

Thank you

[@hossamninga7388]

Good job thankyou

[@mehdibehroozpour332]

ممنون.از روی همین ایده یه سمباده نواری ساختم🙏🙏

[@mehdibehroozpour332]

آره خوب بود منم سنگ سمباده داشتم از روی همین ایده تبدیل به سمباده نواری کردم

[@bryanverran8841]

Thanks

[@МишаСтарый-б5л]

Отлично 👍👍👍

[@skoparweaver7692]

Careful wearing gloves around rotating machinery like a drill press - it's a great way to lose a hand or get dragged into the machine. Other than that - great build and you've given me some ideas.

[@alrubaye81]

بماذا يمكن ان اعوض ذراع الهايدوليك الذي وضعته ؟ لاني لا املك واحد؟

[@emmalelef8952]

Please how to get the plan ?

[@scottpelka1211]

Hi... nice job. One comment I would have is make the table for the sander higher so if someone wants to grind something it can be done from the right or left side wants to sand a long piece like a knife or other item.

[@valeryn4704]

Hello. The part that serves to tighten the belt (a gas stop rests against it and a tensioning roller is installed on it) - why is it fixed on the main rack close to the moving tape, and not along the axis of the main rack and not closer to the tensioning roller. Is it caused by something?

[@xavierdesaegher7353]

Wonderful and your explaination are as well

[@jhonarief]

Thank you, I'm glad that you like it

[@dragonUSNr]

Great video!!! What size belt is that?

[@jhonarief]

4 x 36 or 100 mm x 915mm

[@a.cotrimluis7580]

👍🔝

[@sangteahauhnar5482]

Phaileng lamah pathum minlo thawn thei a ngem

[@sangteahauhnar5482]

A tha hle mai, minlo siam sak ve ka pu

[@dougi2dope]

How strong is the gas strut? Different one lift different weights!

[@jhonarief]

If you look at mine is 150N is little bit to much force for this belt grinder thats why I recomended buy 80N gas spring . that because if its to strong then the tension will be more and belt grinder sound will to loud because amount of pressure at the bearings

[@tomayrscotland6890]

Hi Fella' what animation program are you using?. Tom Scotland. it looks just great to use. Ps the bench grinder is just tops too. thanks for the video.

[@jhonarief]

I use sketch up, thank you

[@sigung01]

Brilliant

[@jhonarief]

Thank you

[@gcfrede]

You should not weld galvanized steel, its toxic :( other than that good idea :)

[@howardsnyder7402]

I hope you are using cutting oil, NOT WD40, for drilling.

[@makermaniacdiy]

ottimo lavoro complimenti, lo condivido sul mio gruppo

[@jhonarief]

thank you so much for sharing my content

[@Kebekwoodcraft7375]

I never use cutting oil for drilling I think it's over use !

[@alk5749]

wouldn't want to use any of your dull drill bits, and yes without some sort of cutting oil you reduce the bit life by a lot.

[@Kebekwoodcraft7375]

@@alk5749 I have to say my drills bits are very sharp it’s what I mean you presume cause I don’t use oil they are getting bad !

[@Kebekwoodcraft7375]

@@alk5749 it’s more about speed and pressure !

[@alk5749]

@@Kebekwoodcraft7375 speed, pressure and lubrication. The absents of any of those is failure.

[@muhiddinnuriddinov68]

Скажите мне пожалуйста... Зачем делать на двух роликах когда можно сделать на одном ролике 🤔

[@harisupriadi7017]

Bench grinder nya brp pk?

[@jhonarief]

Yg 350watt

[@jhonarief]

Bench grinder yg 8 inch

[@harisupriadi7017]

@@jhonarief cukup kuat?

[@jhonarief]

Sudah saya pergunakan buat besi dan kayu tidak ada masalah om? Jgn kawatir dia rpmnya tinggi jadi ngga perlu ditekan kuat dia sudah bisa mengikis dengan mudah baik besi ataupun kayu

[@harisupriadi7017]

Terimakasih infonya 🙏

[@bennyhartono4742]

Do you make the sandpaper yourself?

[@jhonarief]

Yes, wow how you notice that? I will posted how to have strong joint that sand paper on my next project

[@bennyhartono4742]

@@jhonarief i can't wait to see that👍

[@jhonarief]

But dont worry this diy belt sander can use common belt sander on the market with size 4x36 inch / 100x 915mm there is available at home depo

[@jhonarief]

Wait on next sunday I will posted for you, Thank you for stay tune at my channel, cheers

[@rijalvandry7367]

Bsa jiplak autoplan nya mas

[@jhonarief]

Silahkan mas

[@rijalvandry7367]

Boleh mnta autocad nya mas..sya tertarik bikin juga.. simple 👍👍

[@jhonarief]

@@rijalvandry7367 saya gak ada Acad mas soalnya gak bisa pakenya, saya pake sketchup 2019 itu aja filenya cuman divideo aja file mentahnya udah gak tau kemana mas

[@Im_Still_LightSpeedLayne]

Good job. Might I give one small piece of advice. Maybe not use a tack hammer to center punch. I know it’s nit picking and maybe it’s the only hammer that you have. Not trying to be a douche bag, just tryin to help. Anyway, great video. And I liked that you edited in the plans throughout.

[@jhonarief]

Thank you so much

[@jstrndm945]

Itu las apa namanya?

[@jstrndm945]

Boleh minta plan nya gak mas?

[@jhonarief]

Itu las mig mas

[@jstrndm945]

@@jhonarief emang ga pake besi stick yg biasa buat las ya?

[@jhonarief]

Kebetulan saya newbie klo pake stik biasa seringnya lengket makanya pindah ke las mig mas

[@brandonshofner5806]

Music tried hard to ruin an otherwise great build.

[@lesstime1678]

100000000 MPH , not for me boy