Build the Titanic issues 37 and 38 from Hachette

Welcome to my channel for issues 37 and 38 of the Titanic build.
Todays video we fit the motor into its casing and then connect it to the engine floor with the shafts in place and test the operation of the engines.
Please enjoy and subscribe to my channel. Thanks for watching!
00:00 Introduction
00:16 Welcome
02:40 Issue 37
06:23 Issue 38
13:29 Finale

[@straightmanforever69]

Truly a masterclass in model making! Great work John!

[@JohnsModelmaking]

Thank you 😊

[@geordiedave7265]

Brilliant build looking fwd to doing these issues

[@JohnsModelmaking]

Thanks 😊 Have fun!

[@philliposborn808]

Doesn't the engine room look brilliant John? I've been playing with the engines for quite a while, and they all work fine, playing with them so much, I don't want to wear them out before the ship is built lol 😂. Lovely video John, enjoyed!

[@JohnsModelmaking]

Thanks Phillip 😊 It does look great in motion and there are more engine parts in the next video.

[@davemacbuilds5232]

Brilliant work John, i just hope mine works as well as yours, great video

[@JohnsModelmaking]

Thanks Dave 😀

[@rodadams8422]

This is amazing well done John 👏

[@JohnsModelmaking]

Thanks Rod 😊

[@davidc9012]

Very cool, i like 👍👍👍

[@JohnsModelmaking]

Thanks for watching 👀 🙂

[@eddywells5689]

Great vid 🍺🍺💞💞🙏🙏👍👍💪💪

[@JohnsModelmaking]

Thanks Eddy 😀

[@franksteinbach977]

Super

[@JohnsModelmaking]

Thank you 😊

[@pattersonmichael]

Do you know how many total issues there are? Always a great video!

[@JohnsModelmaking]

Not sure if its 120 issues or 140. The Hachette website is down at the moment.

[@pattersonmichael]

@@JohnsModelmaking Thank you!

[@AWF1000]

don't push the plug in too far in the power board when testing. It's a nightmare wedging it back out.. I also need to back track.. the middle engine rod is going 1 way but it's not going the other way when I switch the direction. Not sure if the board is broken on arrival or it's my fault.

[@JohnsModelmaking]

I don't think there is anything wrong as 1 of the cogs allows that to happen. Check the instructions. Thanks for watching.

[@AWF1000]

@@JohnsModelmaking it's ok mate . I was just losing my mind. Nothing was wrong with it at all.. 3 cogs go 1 way and 2 go the other way.. it was mean't to do that. 😅🤣

[@marcusj2283]

Hello John im wondering has anyone els had problems with the engines catching and not turning very well as the one engine on my build hardly turns as id would like to hopefully find out why its doing that please before i connect the motor up please and thanks

[@JohnsModelmaking]

Some builders have had issues. Check the shafts are correct and the end bracket as this is a common misalignment. Thanks for watching!😃

[@pattersonmichael]

I am in the US and we only have 1 engine complete so far. I actually do have a bit of catching on it. I have spent a LOT of time trying to figure out where and can't figure it out. It is like it is perfectly smooth for 90% of the rotation and then it just catches a little somewhere. It is not enough for me to be concerned about (hopefully), but I wish it was perfectly smooth.

[@JohnsModelmaking]

@@pattersonmichael Have you watched my earlier videos for the engine assembly issue?

[@pattersonmichael]

@@JohnsModelmaking Oh yes been following them all the same day they come up! I did un assemble and tried a bunch of things. Even a bit of oil on the moving plastic bits. It still catches somewhere, cant for the life of me figure out where. All good though, I don't believe the catch is bad enough to impact when I eventually connect it to the motor.

[@marcusj2283]

@@JohnsModelmaking thanks iv been working on it tonight and iv got it powered up and both engines now working

[@Marko-ol4yi]

Take her to sea, Mr. Murdoch. Let's stretch her legs!

[@rezakozusko9048]

ᴘʀᴏᴍᴏsᴍ 😘