builders learn to assemble electrical installations

builders learn to assemble electrical installations

[@fatunbiYusuf]

You are not correct, the red from the main source should connected to mains switch, then the black should conect to the lamp holder, while the red from lamp holder should connected through the red from switch

[@derekmcavoy6682]

Correct

[@saleemthupseetechnologies4166]

Agree it's wrong

[@АбатАбиев]

ДА НЕ БЕРИТЕ В ГОЛОВУ ! ЭТО ГАСТРОБАЙТЕР ! ТЯП - ЛЯП ⚡️🔥! 😂😂😂😂😂 ...

[@sambearing7687]

@@АбатАбиев Точно! Он ГАСТРОбайтер, а ты ГАСТАРбайтер)))

[@juancarloschoqquecalachoa1524]

😂 Salvo que en su convención el negro sea la fase y el rojo el neutro. Es cuestión que lo detalle en el plano.

[@OLT-fw7fg]

Выключатель работает всегда на разрыв или включение красного провода то есть (( фазного )) . А чёрный провод то есть (( ноль )) всегда идёт сразу на лампу напрямую .

[@АлександрБелюрка-н9т]

Учитель какой-то баран , чему других , научит ? Такому же , бестолочь .

[@DirkVesper]

Ja schon , aber dennoch sollte die Phase zum Schalter und dann auf den Sockelkontakt der Lampe ...... Aber vielleicht ist das bei euch ja auch egal , aber bei uns nicht ....😂😂

[@Lensamemori]

@@OLT-fw7fg That right..👍

[@konstantinivanov5584]

@@OLT-fw7fg кто сказал, что фазный красный??

[@странникстранник-ш1н]

Какое это имеет значение в переменном токе??? Ты вилку прибора вставляешь всегда в одном положении??

[@satriabajaringan9766]

Seharusnya kabel merah itu ke saklar mas. Karena kabel setrum. Kalo ke lampu langsung itu biasanya masih nyala redup kedip kecil dan berbahaya bagi manusia kalo terpegang, meski saklar sudah di matikan tetap ada setrumnya.

[@ruslanruslan6835]

Betul yg abang bilang ,pase atau kabel warna merah itu ke saklar dulu,nanti yg netral atau kabel warna itam itu ke lampu

[@Komatsu05-z9j]

Iya betul mas👍

[@Komatsu05-z9j]

Iya ,harus nya yg di putus itu strum nya

[@dwimulyati1440]

Yang ada fasanya itu kabel hitam,itu sudah standard,kecuali arus DC merah pasti plus

[@satriabajaringan9766]

@@dwimulyati1440 Kayaknya itu model jadul mas. Rumah masih kayu gedEk, iya kalo itu hitam fasanya. Rumah saya juga kabel hitam itu fasa. Kayaknya modern jaman sekarang sudah ganti deh, kalau tidak salah .

[@ChilesheMwamba-em5qz]

This connection are wrong,red from supply should pass through the switch first

[@rameshkuraba9596]

Stupid

[@shadowwalker4633]

In one phase doesnt matter where you put the switch cuz the only thing it does it opens the circuit .The only thing thats different is you need to trip breakers instead of switch if you want to change light cuz of the active live up there -to keep it simple always phase through switch but this way works as well and in many cases makes no difference at all

[@-algodoo-]

@@shadowwalker4633 wrong. It does matter for safety reason. If it is not passed through the switch first, the contact at the fixture will be live at all time, which can shock the person who are trying to replace the light bulb, if the person expects there are no live wire since the person turned it off at the switch. If the live wire is passed through the switch first, there will be no live wire at the fixture when the switch is turned off.

[@shadowwalker4633]

@@-algodoo- thats what i exactly said trip the breaker not just switch and people changing those lights should check either way so shouldnt be much off a problem if you have a gfci even touching it

[@chandramohanpai2082]

​@@-algodoo-he is an Electrician from Pakistan they always do opposite to other world why simply scratch our head on such foolish videos

[@Rustamkumar12]

पहले electrician का काम बढ़िया से सिख लो फिर दुसरे को बताना ❤❤❤

[@rajpalrajpal688]

Red wire phase, This connection is not correct

[@Duffer529]

I mean it still works I suppose, just doesn't make sense why he did it like that

[@konstantinivanov5584]

Фаза идёт по чёрному проводу

[@pp41385]

When the helper becomes the lineman.

[@andrewlegwale7895]

Don't mislead people. SABS Code of practice...or SANS

[@andresantonio2150]

The people watching your video learn how to install electric in a wrong way.

[@Dagimw]

please use color code

[@eligormezano5433]

לזה קוראים חיבור מנורה בטור

[@abdi-azisabdirahman4787]

The hot line must be through the switch first then the lamp

[@Sam-vn6hd]

Open neutral is a good idea to get yourself shocked on every outlet 😂

[@dannyjamison8337]

The first connection he made was source neutral to neutral at fixture. Second connection was source hot to switch in. Third connection was switch out to fixture hot. It's all perfectly fine, except he should have used wire nuts instead of tape and used the correct wire colors. The wiring itself is fine, since neutral is constant and hot is switched.

[@intelcorei0364]

Agree

[@ugojismart4141]

@@intelcorei0364 that incorrect 😤

[@ugojismart4141]

Incorrect look at the practical work well before analyzing it.

[@intelcorei0364]

@@ugojismart4141 😝😝

[@Erin-jt9di]

How showing us an outside light with plug attachments

[@amarnathamarnath283]

Always follow the color code

[@dwaynedumas5278]

IF YOU WANT TO BE WRONG

[@MOSESJULIUS-f4d]

That's what i know

[@MOSESJULIUS-f4d]

​@@dwaynedumas5278 😂😂

[@Jimbojo]

Exactly how NOT to do this correctly.

[@hicha1699]

how to do it then ?

[@Jimbojo]

@@hicha1699 Okay first, never splice wires by twisting and taping them. Always try to use cable connectors with proper insulation. This can mean block connectors or bladed crimp connectors where no bare wire shows. If you absolutely must splice wires then use heat shrink insulators and solder the wires together in-line. Secondly use modules with terminals not loose wires. A light-fitting and switch should both have mounting holes with screw-fastening sockets. They cost the same or less as those in the video and are infinitely safer. With those you have input/outputs for each wire pairing. There are different circuit types used globally and standards differ somewhat. Some use individual spurs from a common rail for circuits, some use a ring main with a balanced load but regardless of this you should use PROPER SAFETY CONSIDERATIONS when fitting utilities. This video shows rhe least effective splicing done in the most dangerous manner. No mention of safety was ever made. This is not sufficient information to teach someone how to handle a potentially lethal system.

[@renevargas7391]

La fase debe ir al interruptor y luego al centro del soquet, el neutro va directo al otro contacto del soquet ¡Avíspate!

[@АлександрБелюрка-н9т]

Если говорить проще , чёрный идёт по прямой , красный с крсными , пришёл с щита или счётчика пощёл на выключятель и черный провод выщел уже с выключятнля прерывателя и на красный правельное подключение , только. Цвет черный поменять на синий (ноль) иногда бывает черный .

[@konstantinivanov5584]

Здесь чёрный провод это фаза

[@thecreativehomade942]

Agar lebih amannya standar warna kabel kelistrikan harus tetap dijaga dan dipertahankan, untuk memasang saklar yang diputus harusnya yang merah..👍

[@agatatristan126]

Sepemikiran.. Kabel merah umumnya arus + kabel hitam arus -

[@АлександрБелюрка-н9т]

Такие цвета проводов в Европе , в электронных сигаретах + красный и минус черн провод . По коробкам распредилитпльным как на видео , по правелам бебозасности идёт 3 провода , коричневый фаза (+) синий (-) минус . И желтый с зелеными полосками заземление , посторонний ноль . Это какой то детский сад !

[@SardyonSimamora]

Sama,,harusnya kabel merah + ke stop kontak

[@rinipurba6039]

Saklar dh off tp fiting masih ada arusnya

[@tkbhavya8753]

സുഹൃത്തേ ചുവപ്പ് നിറത്തിലുള്ളതാണ് ഫെയ്സ് അതിലാണ് സ്സ്വിച്ച് കൊടുക്കേണ്ടത്

[@rickyboykemusiq5567]

neutral wire through the switch!???

[@АлександрБелюрка-н9т]

Две пары поменять местами ввод в коробку и и провода на патрон поменять местами , и будет по технике безопасности , по правелам.

[@LenaKisielewska]

👏👏 Dzięki takiemu połączeniu żarówka zawsze jest "pod napięciem". Montując włącznik na przewodzie neutralnym udowodniłeś że jesteś " mistrzem elektryki"

[@ImadBinGakJelas]

Ingat Yang Turun Ke Saklar Itu + Plus Bukan _ Min 👈 Karena Berbahaya 👈Dan Ingat Kabel SNI Kabel Merah Adalah Plus Kalau Biru Adalah Netral

[@Entistea-n2r]

Mungkin versi dia berbeda bang..hitam plus..merah min😂😂😂

[@marlonhernandez8411]

For these amateur electricians work, I don't want to change a single switch in my apartment

[@tkbhavya8753]

സുഹൃത്തേ ഇത് എന്താണ് കാണിക്കുന്നത് നിയമങ്ങൾ ഒന്നും പാലിക്കുന്നില്ല

[@jean-marcflaux8062]

Exemple à ne pas suivre. Aucunes règles de sécurité et des règles d’électricité.

[@irvingzebedeegaddi4883]

That's simple electricity installation duh

[@JosueBASSONGUELA-iu3ei]

It's simple and clear ! You guys just try to understand the background of his circuit...

[@AndreYunus-l6b]

Seharusnya fungsi warna cable itu dipergunakan dengan tepat. Sehingga penonton tidak salah paham jika ingin belajar menjadi instalatir. Terimakasih.

[@yesemve]

This fellow knows "cutting wires and joining them" That is all and wandering as electrician

[@rohiliilly918]

Make sure, a black wire is a neutral, red phase...

[@DirkVesper]

Wer macht den sowas ? ?😂 Bei uns kriegt man für sowas gleich eine Abmahnung und zudem gibt es dafür Wageklemmen !

[@victorguirin]

Asi siempre queda el positivo directo a la lámpara y puede generar un accidente al querer cambiarla.

[@raulsv9730]

Para una conexion correcta debes basarte en codigos de colores segun NEC, la forma esta equivocada y puede producir un fallo eléctrico, rojo y negro como positivo y negativo solo aplica en electronica y no en electricidad amigo

[@joetapesana4714]

Thank you for making my day. I had a good laugh. This is one of the best circuits, wrong in every aspect. Thank you.

[@brandondunn-moodie1544]

Why even have colored wires if you're just going to ignore them 🤣

[@nkgajjar]

This connection will burn home easily because phase your are connected to direct lamp holder and this is continued supply will run on holder incase of water drops on it it will burn holder

[@shadowwalker4633]

The switch does still open the circuit so no current goes on an open circuit - even with a switch you have both live and neutral in the bulb and with a circuit breaker which is a must everywhere no problems will happen whatsoever

[@lillybelm9329]

Esa conexión está mal ejecutada, porque conecto la fuerza directamente a la lámpara y es al Swich donde debe entrar y de allí a la lámpara y de la lámpara al neutro Se supone q el Swich es el que abre y cierra el circuito

[@stevewhewell6190]

One wire should be white ti indicate the neutral side. Black and red indicates 240 volt circuit.

[@moulkyahmedcherif4325]

Merci beaucoup

[@ronaldcancino6279]

Debias haber tirado los cables directo al foco y al interruptor

[@GaryWilliams-g5z]

The red wire should goes to the switch and the black goes to light

[@SugengCrb]

Perlu diluruskan. Kabel dari power yg direct ke lampu harusnya netral dengan kode warna hitam. Dan phasa warna merah disambung ke saklar.

[@johanfreitez]

me imagino que el cable negro es la fase, de lo contrario la instalacion estaria mal conectada. Saludos

[@rylanredpath4728]

Bro put a mirret on the splicing 😂

[@fabischkamau3193]

Color coding. Black wire doesn't go to the switch but direct to the bulb holder

[@shadowwalker4633]

Well if you know circuits it all the same cuz no matter where you put the switch it ll open and close the circuit-even if neutral goes on switch still will work

[@shadowwalker4633]

Well if you know circuits it all the same cuz no matter where you put the switch it ll open and close the circuit-even if neutral goes on switch still will work

[@Binuchempath]

Phase is the one going to control by the switch not the neutral

[@wladymellaespina9930]

Esa conexión está mala, en Chile la fase es rojo, neutro es blabco y tierra es verde, internacionalmente la fase es marrón o negro, neutro azul y tierra Verde, primero se conecta el neutro en la lámpara, luego baja el retorno y la fase baja directa, así es la conexión correcta.

[@sampsoneleonu2165]

Are wiring surface or conduit. Please explain.there are two types of wiring.when it comes to pipe work

[@jnsxanzo1672]

bisa aja nih si admin, pinter banget caranya biar rame yg komen. nais bro 😁👍🏼

[@SamVernancius]

Warning: Do not following this connection if you are not an electrician. Such tutorials should demonstrate how switches are terminated according to your country's standard and colour coding eg... *Red to Common (supply) *Red to 1 (load) Note: this is Aus/NZ standard Such tutorials like this should not be followed as it may lead to property damage, injury or death. Work safely.

[@wisdombright5116]

In a case where you fellow colour code, the red from the current supply go to the switch, why black go to the bulb, the red from the bulb 💡 go to the switch to connect with the current supply you drop in the switch .

[@robersalsero2803]

El foco enciende igual. El negro ( fase) al interruptor. El rojo al neutro( lampara). No critiquen y aprendan.

[@Mwahyunofansyah]

Sebenarnya untuk 1 saklar cukup 2 sambungan itupun harus kabel merah yang masuk ke saklar karna kabel warna merah umumnya + (positif) jika kabel merah yang langsung ke lampu biasanya lampu akan berkedip walau saklar posisi of

[@АлексейКолпаков-о2х]

В целом грамотно. Только изолента должна быть синей. Чтобы по феншую. И на выключатель должен идти именно фазный провод.

[@jorgeelisandrovilledaareva1209]

Conexión errónea para corriente alterna

[@MarciaMaria-cm4mz]

está errado, fase sempre no interruptor, se informe.kkkk

[@josedicesare2407]

Il cavo rosso e bianco già nel 2020 se non erro, si usa nei circuiti a corrente continua 12/24 volt. Corrente alternata 110/240 volt fase nero oppure grigio, neutro blu.

[@milanchakraborty1052]

Switch fitted on Neutral line,conventionally fitted on phase line,thanks.

[@codmobile434]

Don't use a different color when it is continuity.

[@aurelioabarca9651]

El de la izquierda viene la alimentación rojo fase y negro neutro ,el rojo se comenta al rojo del interruptor y el otro lado del interruptor también debe ser rojo porq sigue siendo fase ,este debe ir al rojo del soquete y el negro de la alimentación al negro del soquete

[@tiburciomoura3445]

ficou perigosa essa ligação com o fase na lampada !!! numa eventual manuteção a asoquete vai estar energizada

[@BEATRIZRUIZ-dc8dc]

Lo más importante no lo dice Qué es un Triguei. Un bombilla que sé apaga con 2 Apagadores

[@earnestshipale7535]

Please use "colour code" don't connect cables of different colours, because it may confuse whoever may come in future to do repairs. All "red" should pass and come from the switch to the lamp, and "black" cables from the lamp going straight to the mains (neutral source cable)

[@indiotaino2277]

Amigo para poder entender esas conexiones hay que mostrar como están conectados los cables en el foco y en el apagador.

[@shivsagarpantnagar5197]

कलर कोड के हिसाब से गलत कनेक्शन है l

[@denisnyambane-ll9bw]

Depends with your main line

[@gualbertorodriguez5184]

Wrong connection if you use the Color coding of cable wire, its mean Hot or Red is "Cut Off" switch

[@ToolmanPRO]

Kalau merah positif dan yang diputus ke saklar negatif, berhati hatilah ketika mengganti bohlam lampu karena arus positif tetap standby. Dan tidak bisa mengganti fitting lampu karen positif dapat membunuhmu.

[@dougjstl1]

The black and the rich be used separately. Because typically the black is the hot wire in the red wire is the hot wire. When there's a red wire though the black wire is ground. When the black wire is a hot wire then it's white should be used as a ground. So I guess this must be DC electric

[@aloisiotadeunettonetto2495]

Se eu tiver que aprender com você eu estou F....vermelho como neutro

[@FernandoToctaguano]

Hola podrías poner un vídeo de cómo instalar un taco conmutador

[@vasekcz230]

Dont forget say, you must turn off the main switch or ⚡💀

[@trannirwana]

Salah besar itu ya, yg kabel arus yg seharus nya mengarah ke saklar ya....

Try using block connector safe than tape

[@AmitKhandelwal-r5p]

This is not a good connection, there is neutral cut from the switch... In a good connection there should be phase cut from the switch. 

[@anwer39]

That's why our elders said jiska kaam usi ko saajhe koi or kare to danka baaje😂

[@RajaKesah]

Kuch kuch hota hai, 😂

[@fabioyakawa]

hot wire always to the switch first

[@hermidesmontero3798]

Yo en mi caso como aporte. No corto tanto los alambres. No ay esa nececidad.

[@robertramirez794]

Perdón amigo está bien esa instalación pero lo q no está bien es el cable q unió con el retorno así hace confundir a un apresdis

[@TamsenJean]

Why do you connect the black with the red

[@ghost-wm1hw]

AC supply live and neutral switch polarity 50 times a second, so the is not really a neutral

[@shadowwalker4633]

Ye thats the point ,but still if you want to change the lights you cant use the switch but need to trip the breaker cuz of the live wire active -thats the only difference but to make it simple just connect neutral there to not confuse or shock future workers

[@DuyenanNguyen-hl1jo]

Dấu vậy khi thay bóng đèn chắc đứng cười hoài luôn

[@عمرويونس-ص2ص]

بدون زعل خلى الطرف الأحمر كهربا

[@josues.3498]

Use o código de cores. Mas pela iniciativa obrigado.

[@mohammad3420]

Imagine if power was on 👁️👄👁️

[@avicenneaveroes1918]

Please respect international rules. The big mistake is using 2 colors for wire. In practice, it's more better to use 3 one. One for phase input connected from input power to switch. A second color for neutral connected from input power to the lamp. A third one to connect switch to the lamp. Without this type of rules, dangerous Dommage can occur.

[@ladydi4051]

Red goes with red & Black with black

[@Xenium_Q]

The lamp is still under voltage if the switch is off

[@gerardoalvaradguuhtrttyttc4825]

El circuito esta mal esta invertido, la face debe de ir al interruptor

[@adrian-ioanfleseriu9503]

The tape isolation is not correct - the point is not enough isolated.

[@FabianSánchez-o2g]

Está mal conectado el rojo face siempre va al apagador y el neutro negro al foco

[@BoasSwaiya]

Red wire is Your positive or neutral wire

[@gavshomebrew]

exactly how to start a fire or elcacute yourself electrical works should always be carried out by a qualified electrician or at the verry least inspected and singed offf by a qualified electrician befor being energised

[@morganmazila5057]

Is the neutral cable going through the switch? Not happy with you colour coding.

[@hassancamara8606]

Good job bro, I will like to do the same job, I am so interesting in this job, ❤❤❤

[@willyanastazi9115]

Umefeli yaan hiyo connection hizo supply mbili neutral na live unaunga supply na common switch wire namwekundu wa taa neutral ya taa na neutral ya supply

[@Subiantanaacim]

Mantap ni ceritanya bagus ngambil setrum kemana

[@FactFinder907]

Wrong color coding , red cable is for the phase and enters the switch via common and exits via L1

[@MichelSantos-rt5bv]

Não entendi essa instalação porque a fase do neutro. Mais lembrando a fase que o disjuntores ou terrepitores desliga e liga tenhe que ser a fase porque se tiver sendo o neutro quando desligar a lâmpada fica passando corrente e se você tirar a lâmpada e topa dentro do bocal você toma choque e a ligação sendo com a fase assim que você desligar a lâmpada corta totalmente a corrente.

[@wilmerjoselopezacosta4748]

Mal incorrecto: el negativo va directo al foco y la corriente va al apagador y del apagador al foco.

[@collinskipngeno4841]

Live supply should be to the switch first then neutral cable to the bulb yours is wrong

[@nelsonromero3521]

Acá en Colombia los colores rojo y negros se usan como fase así que me enrede