In this video i will build a 1 cylinder LEGO Pneumatic Engine. Hope you enjoyed! Music by Karl Casey @WhiteBatAudio • Synthwave / Retrowave ...
Пікірлер: 45
@ManosLC Жыл бұрын
Check out the new version! kzbin.info/www/bejne/mKaYo3-loL99hMU
@railfanmusicboi2 ай бұрын
If you want to build a different pneumatic Lego train, try connecting the piston to the wheels like that of a regular steam locomotive.
@fredzeh6950 Жыл бұрын
Like the Design 🙂
@Dodomacii Жыл бұрын
Try to make an engine that pumps air for itself!
@enricopro1069 Жыл бұрын
It Is impossible
@xXDiver12Xx Жыл бұрын
Interesting. Maybe making the engine power a pump? But it would need to be started to run.
@ramlover25diesel21 Жыл бұрын
It is inposible to make an engine that pumps enough ait to power itself because of the friction takes away so much power
@user-es6wn6pz3e Жыл бұрын
To power itself, it would need to compress a cylinder with equal volume to the one running the engine (or a different mechanism which would lead to the same result but be harder to imagine). For this to be possible, the cylinder running the engine would need higher pressure than the one being compressed, otherwise, it would equalize and stall the engine. Since the cylinder being compressed needs to have lower pressure, it would supply less pressure back than being supplied, and eventually have too little pressure to run. In fact, a compressed air engine pumping air to itself would not even be possible with 0 friction and 0 leaks, since then it would equalize, for it to power itself, it would literally need negative friction.
@xmysef4920 Жыл бұрын
@@user-es6wn6pz3e In other words: It breaks the law of thermodynamics
@wolfgangfischer665710 ай бұрын
Hast du da etwas geklebt. Bei mir gehen die Verbindungen bei 3 Bar auseinander.
@ManosLC10 ай бұрын
No glue was used.
@augustuslyvonne Жыл бұрын
Cool, but who's practicing trombone in the background XD 1:57
@Legostuffidk Жыл бұрын
Try changing the angle of the timing to 90° I find that that works best in pneumatic engines
@Jack19000 Жыл бұрын
there's something called Timing that is needed in any kind of engine
@BananaMan1030 Жыл бұрын
Good point
@GTech_builds7 ай бұрын
well because your piston is not only osilating but partilaly rotating it needs to piviot from the center
@CenReaperYT.7 ай бұрын
Make one that's squishing the tube, not moving a switch
@phroogo...10 ай бұрын
you said camshaft instead of crankshaft the camshaft is a separate shaft with lobes that control the valve timing
@brixbuildz Жыл бұрын
Awesome!
@ManosLC Жыл бұрын
Thanks!
@xXDiver12Xx Жыл бұрын
I think that the engine could be stronger with better timing, just an hypothesis by watching the video in slow-mo.
@gebmity35843 ай бұрын
What pressure should I use for my 1 engine? (Should I make piston intakes more in radius to upgrade pistons power?)
@herojordans2838 Жыл бұрын
Thank you for the inspiration
@miroslavstanisavljevic8292Ай бұрын
how much torque is ?
@marcusthegamer348 Жыл бұрын
You shortened the crankshaft, not the camshaft :)
@ManosLC Жыл бұрын
My bad!
@1iqsquad911 Жыл бұрын
@@ManosLCrip
@wolfgangfischer665710 ай бұрын
Wie viel Luftdruck braucht der Motor
@cheez700 Жыл бұрын
niceeeeeeeeeeeee
@Okkkkkkkkkkkkkkkkkkkkkkkkkkkk9 Жыл бұрын
as the engine worked i got a beamng trophy for no reason lol
@Indonesia557Ай бұрын
mine dosent work i have done everything you did and it still wont work the timing is right but jt just gets stuck it wont even move
@ManosLCАй бұрын
@@Indonesia557 Try a bigger flywheel and gear ratio!