I've put a lot of time and effort into creating this video, so I'd really appreciate it if you could show your support by liking, sharing, and subscribing to our channel for more content like this. You can also find us on Facebook, so please show your support there as well: facebook.com/diy.proknow
Nice video and 3d printed parts. But how those wheels performs? That was the point and you missed it.
@pazsion2 ай бұрын
this was sopposed to demonstrate your idea and test it, but you instead built a whole rc car and didnt test it at all 😔
@hugh_jasso2 ай бұрын
The idea isn't new but I like that you're DIY'ing it. The high quality ones I've seen have the shocks angled perpendicular to the ground on the forward spin so they bite and absorb into the surface better. I would also either go with narrow wheels or increase the number of "spokes" to support the wide wheel base since they're hinged and not a solid connection spoke.
@himadrisinha2005Ай бұрын
I like how the cameraman is running behind the car 😂
@Rose_Butterfly982 ай бұрын
The wheels should be going the other direction so the suspension works better
@masterplayer59822 ай бұрын
The idea is very intriguing ❤! Also something i must say, the shock absorbers allow the mass of the wheel (centre of mass) itself to move anywhere on the plane of rotation this means at high speeds the wheel’s centre of mass would be flung away from the hub bearing. Meaning the car would start hopping instead of rolling if u getting it spinning fast enough 😅
@jweatherly262 ай бұрын
This was exactly my first thought.
@kdt852 ай бұрын
Terrible idea, awesome execution!
@MaxImagination3 ай бұрын
Fabulous work, brother! I admire every bit of effort you put into this project and video... Your video quality and editing are on another level 🔥
@proknow3 ай бұрын
Thank you so much, Max! Your support and feedback mean a lot, especially coming from a fellow creator. I'm really glad you enjoyed the project and the video. Looking forward to seeing more of your amazing work as well! 🔥
@MaxImagination3 ай бұрын
@@proknow Always at your corner with support :) More projects coming from my way as well. Thank you!
@proknow3 ай бұрын
Thank you🙏🙏
@subhamdas882 ай бұрын
3d printed material turns out to be rigid and very well finished. Which 3d printing machine u are using?
@antonnym2142 ай бұрын
I found you today and subscribed immediately. You are awesome! Very fun build! Shukria.
@PankajSharma-ip6ih3 ай бұрын
Hello its Nasa And I spooted you are doing such things and you are under arrest 😂😂
@proknow3 ай бұрын
😂😂🤣
@Mr.GeniusCreation3 ай бұрын
Very creative way of using suspension 😃 Loved it ❤️
@proknow3 ай бұрын
Glad you liked it Sahil 😀
@hu51162 ай бұрын
Very nice! Except you never really shown or talked much (at all?) about how it worked. Might need to compare to a version with regular wheels. I was left hanging as to whether this ended up being a good idea or not.
@Vladimir_Java_dev2 ай бұрын
Отличная красивая работа! Получил эстетическое удовольствие)
@riyanshraj52783 ай бұрын
9:29 What's background sound 😮😍😍😍
@ds-k78782 ай бұрын
잘만든다 잘 만들어, 군더더기 없이 깔끔하게~
@deepaknanda11132 ай бұрын
Ur thumbnail pic is lit🔥🔥🔥
@taralpatel27182 ай бұрын
Very high quality video production. Also very good idea implementation. Well done.
@proknow2 ай бұрын
Thank you very much!😊
@SKAvius.Ай бұрын
Very nice and elegant work! 😉👍 But wouldn't you want to separate the electric motors? Make two axles, two belts, one motor would drive the right wheel and the other motor would drive the left wheel. Then the whole car could make sharper turns much more easily. This would be an easier solution for off-road than installing a differential, because the differential will spin without locking. And you could programmatically adjust the power to each wheel, e.g. put more power to the left wheel when turning right.
@johntuffy57212 ай бұрын
softer spring rate would help alot ..... and some way to keep the rim centred above the hub ....... super cool idea anyway ..... thank you for sharing 😊
@samuelwong41522 ай бұрын
nope, skip it
@Rupali-v1t2 ай бұрын
Means?
@ragibrownak57122 ай бұрын
Fact sponsorblock
@Chris-oj7ro2 ай бұрын
You're right. Stayed for the music though.
@geraldbl2 ай бұрын
You're a hero bro... still watching cos I'm bored
@atharvbhalerao30622 ай бұрын
Thanks!
@keegansillaots43272 ай бұрын
That was a very cool video, man! I had a feeling right away that the wheels wouldn't work. Maybe with more shock absorbers and fastened in a much sturdier way.
@SuperEightOneEight2 ай бұрын
nice idea..perhaps the design of the wheels can be improved to ensure its stability and rigidness..as per my observation ...first..the ball end of the shocks should be eliminated as it promotes variable axis movement..instead use cylindrical shims..these should hold the both end of the shocks more rigid to the rim flanges and center hub at the hex housing...2nd..maybe the wheels is better of with rubber tyres..with soft foam inserts to further enable stabilizing the rolling resistance and jolts from surfaces...only then once the wheels are near fully stable..u can start to play with the spring rates and shock oil viscocity...to get the exciting motion damping experience and uniqueness from the wheels in countering the unsprung weight it bares on the wheel hex and hub....hope my 2 cents sparks new idea for u...have a great days ahead..and keep up the great videos.
@antonnym2142 ай бұрын
Dost, yah ek shandaar pahiye ki design hai
@sageoz98862 ай бұрын
Not really. It’s been tested before many times and it makes zero sense. There’s tons of issues just looking at the design: much more rotational weight, much more unsprung weight, inconsistent suspension absorbing at certain wheel angles, weak lateral rigidity, lateral force shock shaft stiction, shock shafts being drug through dirt, buying extra shocks. There’s so many great reasons why this isn’t a useful design idea
@craftycri2 ай бұрын
Its so funny, I kept expecting you to say you were from the IRS and I needed to get google gift cards to pay off back taxes.
@PersanityАй бұрын
1st thought without watching anything yet: This can't work because the tire would never be on center with the hub and you'd never get a smooth ride at speed. That said, at very slow speeds doing something like rock crawling wheels like these could absolutely work well.
@deanselvyn85792 ай бұрын
This is very interesting, l love watching this kinda stuff.
@ioannisbatas1614Ай бұрын
Superb !!!
@Termini_Man2 ай бұрын
I've seen a similar concept used to a really good effect. In a 1 pound/454 gram combat robot/battle bot called cheesecake, the rims of the wheels are 3d printed (more than likely TPU, but I'm not sure) and have 3 spokes that are springy. they work incredibly well at preventing too much shock from traveling through the wheel and damaging the axles axels or the motor. Combat robotics, especially at the one pound (454 grams) deal with incredible forces, being hit with rotating weapons that store insane amounts of energy, have incredibly powerful weapon and drive motors (even weaker drive motors can spin their tires against the ground),and LiPo batteries can only be used a hand full of times before they are too burnt out. In this harsh field, where a full suspension assembly would be too complex, heavy, and prone to failure, the springy wheels are phenomenal.
@tobins68002 ай бұрын
Check out Softwheel and GeoOrbital wheels. Torsional rigity wasn't there. As someone else had pointed out as well, without using the same words. Softwheel looks like the wheel side is directly attached to the rim of the wheel. That might be key.
@chris9933612 ай бұрын
I think with the shock absorbers angled around the circle the way they are, you would probably want ones that are neutral in the center of their travel so that they can resist motion on extension and compression based on braking versus acceleration forces. Don't quote me on that but it feels like you don't want their natural position to be at full extension.
@miauzure39602 ай бұрын
you didnt even show how the suspension works in slowmo or at least stationary, and that was what I was most waiting for
@dodihsupriyadih92812 ай бұрын
❤❤❤ kamu punya video. Lanjutkan. !!
@caramelcat49872 ай бұрын
This is a very cool concept. I wonder if they will ever use something like this in the future. I like it a lot!
@toolbaggers2 ай бұрын
Those ae shocks/dampers that are only supposed to see loads in one axis. You need struts that can handle the side loads better.
@KB-26-T49_YT16 күн бұрын
This is a fantastic job ❤❤👍🏿👍🏿👍🏿
@insoleafptyptd38012 ай бұрын
Thoroughly enjoyed your video. Very well done and inspirational
@Mr.ky892 ай бұрын
I would love to see it made, thank you
@osevenninefiver2 ай бұрын
you'll need better balance and maybe apply some camber. the centrifugal force around turns and downforce will tighten the suspension in the wheels, and offroading might just be backflips until you get over the obstacle. could try to make the wheels go faster with more downforce and pressure, but then you'll need serious differential set-ups fot curves.
@Anuragkumar997683 ай бұрын
I like your all videos .❤❤❤❤
@proknow3 ай бұрын
It's my pleasure 🙏😃
@sarvagnaraval55293 ай бұрын
Nice dedication and new experiment.. totally appreciated 🎉👍👍
@proknow3 ай бұрын
Thank man 😃
@gsestream2 ай бұрын
nice idea, even better, you can but an electric hub motor in the middle, also. you could also try spiral leaf spring wheels.
@dylanhalifaux2 ай бұрын
I wonder how gyroscopic procession will affect this. You might find that the forces are being applied at 90 degrees to the ground, and the wheels will just slide forward relative to the axle.
@desibaabooАй бұрын
The way Shocks placed under the wheels ,killed the DOF of suspension (degree of freedom).civil,mech,robotics Engineers can easily get my point.
@pariskulkarni81133 ай бұрын
Best cinematics sir ❤, Bhaiya 😅
@proknow3 ай бұрын
Thank you so much, Jai Shree Ram🙏!
@myroboo3 ай бұрын
Wow Nice design brother ❤👌👌
@proknow3 ай бұрын
Thank you so much
@patrickradcliffe38372 ай бұрын
If you're using a 3D printer, it would have been better to design compliant wheel hubs with multiple spokes that would absorb impacts. The biggest issue I see is axle pulling the shocks apart under heavy torque.
@linosuazorojas68412 ай бұрын
si le pusieras alas plegables con servos y un motor pequeño con Helice eso podria volar como un hibrido de auto y avion
@octaviooyhanarte95742 ай бұрын
Está hecho con metal, no va a volar. Sería demasiado pesado
@Vishad_Vishwakarma4 күн бұрын
very nice concept but needs some stronger rc car tyres not the printed ones
@VijayadasaDemian3 ай бұрын
amazing bro
@proknow3 ай бұрын
Thank you so much 😀
@vedantvaidya1532 ай бұрын
bro u are a great engineer btw i have liked and subbsd
@Dirt9752 ай бұрын
This music goes hard
@anasmr.a30412 ай бұрын
How to make long range recever and transmitter
@web3student2 ай бұрын
Man you really did it from scratch huh !! Impressive !!!!!!
@rlrentertainmentsinventions3 ай бұрын
Super bro ❤ I love tyres very much in this Car.
@AbhinavKumar-ne1Ай бұрын
Congratulations and your efforts are great 3D printed parts are of great quality last but not least the amount of time and efforts put into it are beyond excellence ❤🎉
@AnshumanIngale2 ай бұрын
The components of normal force of mg is always at an angle with the shockers so how would the spring get pressed only on three points on wheels it is usefulo
@p.k.9532 ай бұрын
this will be similar to a soil compactor i guess
@yxhankun4 күн бұрын
Well done. Can u explain the function in using eeprom in the transmitter? For storing mac address in 2 bytes of eeprom. Why receiver not use eeprom?
@armanchakraborty56702 ай бұрын
What is the compression length of the shock absorbers u used?
@theprotestant96312 ай бұрын
Awesome! Impeccable precision, Art at its finest. Love it. 👍
@proknow2 ай бұрын
Thanks😀
@abirgaming71393 ай бұрын
Love from Bangladesh brother ❤
@proknow3 ай бұрын
Thanks for your support❤️
@SkateboarderPawan772 ай бұрын
Appreciate 😊
@UttarkumarfanfilmsАй бұрын
Bhai agar shoker tut gaye toh isse bhut bada hadsha hosakta hai or jaan bhi ja sakti hai isse acha toh normal shoker hi thik hai. Bhai hm toh apna shok hi sheh lenge. 💯💯💯
@proknowАй бұрын
😂😁
@xtremegamer8668Ай бұрын
Can you attach a solar panel
@PiterRI2 ай бұрын
Ini sangat keren kawan
@proknow2 ай бұрын
Thanks😊
@powerstargaming6402Ай бұрын
Super bro ❤❤
@AKElectroDIY3 ай бұрын
Nice project
@proknow3 ай бұрын
Thanks😊
@Thuliolima20083 ай бұрын
Very Good
@proknow3 ай бұрын
Thanks😊
@Uttso_Official3 ай бұрын
Miss you bro.❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤
@Supergt950218 күн бұрын
Nice 👍💯
@NoticedVeil67753 ай бұрын
Very innovative project what is the cost of this project brother?
@harendrajatav58212 ай бұрын
Good ❤ work
@proknow2 ай бұрын
Thanks ✌️
@Quantic-Frequency3 ай бұрын
the best chanel of the world
@proknow3 ай бұрын
Oh my Goodness, Thank you very much, brother😀🙏
@Quantic-Frequency2 ай бұрын
@@proknow Yes I can not say lies I love engineering
@Hararion2 ай бұрын
I think the concept will doesn’t work because of the centrifuge forces implied on the rotational axis of the wheels, also it have several vector forces aiming in all directions on the same axis, so the shocks absorbers just tend to stiff and doesn’t absorb the impacts… and on top of that, if the rotation of the wheels are faster, the system becomes less effective because the centrifuge forces are more strong…
@NothingBurger862 ай бұрын
maybe the design could be modified to be more resistant to torsion. (adding an extra 3 coilovers, while keeping the number of hub mounting points at 3.)
@NothingBurger862 ай бұрын
by the way, I have considered the concept of replacing the coilovers with tensioned bungee cord.
@asaljdsimplecraft29172 ай бұрын
good job bro
@proknow2 ай бұрын
Thanks😊
@Sir-Dexter21 күн бұрын
nice work
@proknow20 күн бұрын
Thanks🙏
@user-ql4nk4ox1n3 ай бұрын
When you make rc boat
@cho7official552 ай бұрын
I love the part where you test it out :/
@proknow2 ай бұрын
Glad, you loved it. Thank you
@Shimbhuram-df5ngАй бұрын
हिंदी में बनाया कर ज्यादा व्यूज आएंगे❤😂🎉😢😢😮
@BrandanRodriguesАй бұрын
Bro you just need to make the will flexible and that might work
@vizibug2 ай бұрын
struts don't like side loads..
@syedhasnain745624 күн бұрын
Hi do you need a website
@AnayVats2 ай бұрын
I want to know and your support how to program aurdino for making rc Bluetooth car
@dhirajbanpurkar53973 ай бұрын
plz bro make video on how to make brushed drone using node mcu esp8266 module 🧐
@proknow3 ай бұрын
Ok, Noted.
@dhirajbanpurkar53973 ай бұрын
@@proknow Plzz
@Zane.Wellnitz2 ай бұрын
The torque of the engine is going to screw with the functionality of the shocks
@tharunjayakumar2563 ай бұрын
try using TPU filament for 3d printing your wheels. This is an advice from this 12 year old
@proknow3 ай бұрын
I printed the tyre with TPU, and that transparent filament is TPU, Sorry I forgot to mention it in the video.
@tharunjayakumar2563 ай бұрын
@@proknow if the wheel is made of TPU then there is no need of spring it is not required. but you can try making it into 3 parts so that there will be some action from springs
@HURKICHUN2 ай бұрын
아이디어는 좋은데 휠의 흔들림으로 직진성이 좀 떨어질듯 합니다.
@sanych98482 ай бұрын
Нельзя смещать ценр масс колеса! Это работать будет только на очень низких скоростях вращения колеса. А так же колесо не будет иметь устоичевость к поперечным нагрузкам.
@ThePalsanich2 ай бұрын
The author invented a wheel with spokes. With elastic and shock-absorbing spokes. Nice try. Like and subscribe 👍
@DarioushAryan2 ай бұрын
bravoo
@rajneeshyadav83252 ай бұрын
You didn't install differential drive that why facing turning problem
@proknow2 ай бұрын
I am planning to use the differential in my upcoming car videos.
@riduanmuntasir18013 ай бұрын
Your idea??? sorry to say many youtuber has already made this kind of suspension.
@rinner28012 ай бұрын
Good video, but the music kinda sux ;}
@yogikumar45162 ай бұрын
Amazing idea bro.. . ❤
@powerstargaming6402Ай бұрын
Bro design a Kalki movie bujj rc car❤❤❤
@proknowАй бұрын
I already have in mind, I will do it soon.
@sakethram86162 ай бұрын
Use differential bro
@angryhusky24672 ай бұрын
The suspensions are at their max so they wont provide any travel on the bumps because is one trys to move down other two will stop it. Although you have kept them at an angle but at such scale that wont provide any major benefit. The suspension is not providing both up and down motion, its providing only down motion for the vertical and no up motion for the other two. So check the suspension travel. Cant say anything about the stability though.
@vixu_xivu2 ай бұрын
To bad it iuncreases roling resistance. There was a bike with a similar concept. It was several wears ago. Did'nt hear about it again.
@harishp69242 ай бұрын
How to rotate bldc motor clockwise and anti clockwise
@proknow2 ай бұрын
Just exchange any two wires from the 3-phase connection between the BLDC motor and ESC.