ABS need this calibration after changing the ABS ECU ,Yawratw or Grate sensor or Resetting ABS memory in scanner.#toyota #auto #india #english
Пікірлер: 28
@sahidnurfatah9533Ай бұрын
Very helpful thanks brother
@ismailaloum10416 ай бұрын
Nice video and very helpful ❤
@chomper4x44 ай бұрын
Is the recalibration code for c1345 procedure the same on a 2007 toyota camry hybrid? Thank you Sir for your video and response.
@muhammadjamil12047 ай бұрын
mashalla
@60411diego27 күн бұрын
If it dosen't finish the calibration you need a new abs unit from the dealer
@josegarcia-th3pj4 ай бұрын
in my case blinking stop half the way and calibration is not done, do you think is hardware or air in the system
@johnnygomez86936 ай бұрын
Hi thank you for the video... After reset memory i go to calibrate and the lights wont bling fast meaning it does not want to calibrate can you help me figure out why?
@yutubkuful10 ай бұрын
Salam, im from Indonesia, i do likes that on Camry HV 2011, do w/ thinkcar2 scanner and w/ GTS Toyota , but the both not solved yet. Kondition : Pump+accumulator has changed w new. d u have any clue ? thx b4
@ricardoandrade13132 ай бұрын
I appreciate you, LETTTT'S FUCK!NG GOOOOO!!
@buyingocharles6641Ай бұрын
But mine stops half way what could be the problem 😊
@tsanaat620410 ай бұрын
Hello I did a calibration on the C1345 code but it is still on the board. What can I check now? I look forward to hearing from you. Thank you
@JohnDoe-j7s2c8 ай бұрын
Ever figure this out I went through the whole procedure and bleeding with a Topdon scanner and C1345 and C1368 won’t clear. Installed used booster and pump doubt they are also bad 🤷♂️
@johnshin46455 ай бұрын
@@JohnDoe-j7s2c bleeding air from every wheel caliber ?
@JohnDoe-j7s2c5 ай бұрын
@@johnshin4645, I ended up going new. The issue was the used booster. I then used my original booster and used accumulator pumps from the junkyard and was still hearing the pump run and run and run. I assume the booster had an internal leak or malfunction. I purchased new pump and booster from dealer at a rate of $1300 which is insane money and it calibrated fine. In short, I’d just replace with a new unit unless you can verify 1. The used unit is/was upgraded with the service campaign/bought new or that the used unit has under 100k or less (rare). The job isn’t fun and bleeding isn’t either. Not worth the time to do this 2-3 times.
@karimkhan-tz6lb Жыл бұрын
After reset memory when liner soliniod offset not Learning r calibrating why ?? What is the reason
@autoskills1476 Жыл бұрын
Then perhaps your accumulator pressure is low..
@Xbubba1p Жыл бұрын
@@autoskills1476 so that can cause it not to clear
@johnshin46455 ай бұрын
@@autoskills1476need to change abs motor?
@birbalyadav2358 Жыл бұрын
What scanner did you use here?
@autoskills1476 Жыл бұрын
Its launch 43q pro
@amazonautomotive3492 Жыл бұрын
Hello, you have a Toyota softwer?
@autoskills1476 Жыл бұрын
Launch x431 pro
@ramdanelimam4002 Жыл бұрын
salam , what scannner model your scanner?
@autoskills1476 Жыл бұрын
Launch x431 pro
@ashrfzenh Жыл бұрын
Can i communicate with you
@autoskills1476 Жыл бұрын
00923118000345 watsapp
@arifshah1130 Жыл бұрын
Bhai Urdu mein video bannao thank u
@autoskills1476 Жыл бұрын
English international zuban he.urdu me bi videos available he.thank you