Autodesk Inventor Tutorial For Beginners Exercise 5

we will create a 3D model in Autodesk Inventor 2017.we will learn Sketch ,Extrude and Cut commands.
3D modelling in Autodesk Inventor
1)Autodesk inventor Tutorial for beginners Exercise 1
• Autodesk inventor Tuto...
2)Autodesk inventor Tutorial for beginners Exercise 2
• Autodesk inventor Tuto...
3)Autodesk inventor Tutorial for beginners Exercise 3
• Autodesk inventor Tuto...
4)Autodesk inventor Tutorial for beginners Exercise 4
• Autodesk inventor Tuto...
5)Autodesk inventor Tutorial Design of Fidget Spinner
• Autodesk inventor Tuto...
6)Autodesk inventor Tutorial Emboss and engrave
• Autodesk inventor Tuto...
7)Autodesk inventor Tutorial How to make 3D Pipe
• Autodesk inventor Tuto...
like Facebook page.
/ cadcamtutorial
Subscribe our KZbin Channel.
/ cadcamtutorial

[@AyanAli-ew9sw]

I drew the two circles then drew a centre line down 75mm then used offset on that line to draw the other three lines at 5,5,25 and 25mm touching the two circles. Then finished off by trimming and i was ready to extrude. So much easier to draw the first face

[@solarwinds-]

Thank you so much for posting all of these tutorials.

[@afzaalyousufi]

Good work sir .... Here is my question .. How you choose plane for start working ... ???

[@iheanyinwamma503]

I am asking the same question.

[@alinabechet1819]

Hi Sir, thank you for detail tutorial

[@EduardSidorov-i3f]

Спасибо за урок.

[@lilynabilah2865]

its look easy for me..tq share this video

[@simpilothr6653]

I really do appreciate your work, but I have one big questions... Why do you need to transform the lines to "Construction" if you don't even need to? Is it to make it more complex or right, or is it the right way to do it? Thanks for doing these kind of tutorials, really did learned a lot about using Inventor! Cheers!

[@simpilothr6653]

Edit: Sorry, now I got the point of the "Construction" command, never mind. Thanks once again!

[@maameefuamensah]

@@simpilothr6653 please share

[@boivi4898]

Hi Sir, can you help me, about to choose plane from XY plane to XZ (bottom) on isometric, when i sketch on bottom plane but when i view as isometric it show top plane. thanks for your help.

[@xdygmnyrdf]

These tutorials are wonderful

[@vvv7692]

i`m learning a lot from you tutorial, but for the love of god, you make more mistakes then i do. for exemple i learned from you play with tangent lines and in this video you did big f at the last part.

[@hameedetemadi8390]

Good job

[@chrishing8491]

which do you like more Autodesk Inventor or Solidworks ?

[@allieb9258]

when making the rib, you can just use the center snap points to make the rib line

[@smartcricofficial7622]

He didn't use rib extruded it

[@nickidas876]

Hello sir, Can you do a tutorial how to design low rpm permanent magnet alternator. if so would be thankfull

[@allieb9258]

nice!!

[@shravankumar4963]

Thank you sir

[@Rk-rj7xk]

Hello, that rib sketch was not Constrained... why ???

[@FormadorCAD]

He forgot to apply one more tangent constraint. Thats the reason the sketch is not fully constraint. The rib could have done it more easily with the Rib command. Anyway, sorry but too many mistakes to be a good tutorial.

[@allieb9258]

now i get the "project geometry" command!!

[@tyrefactstamil1254]

how to get job in design field? can diploma mechanical engineer goo for it?

[@shereali4010]

yes

[@santoshkeshari829]

My constrain feature is not working what to do

[@solarwinds-]

😃

[@onurkahraman1167]

Can you also prepare a tutoriol about siemens nx ?

[@deepakdsp475]

gooood...