Can-Am Ryker Handlebar End Weights

[@Slingmods]

🛒 Ryker Handlebar End Weights available here: www.slingmods.com/canam-ryker-handlebar-end-weights

[@mamamac_65]

Just ordered! Can't wait to get them!

[@ramchhabra877]

Great product. So easy to install

[@delandrickjohnson8982]

Can someone tell me what size screws those are where I can get some at.

[@mfmclain]

Not sure what happened with my 2022, but the new screw bottomed out on the square nut and got stuck stripping the screw and I’m guessing damaging the mirror assembly. The screw wasn’t over tightened either, as there is still screw exposed on the bar end side.

[@Slingmods]

Hey Matthew.. oh man... those factory square nuts are a poor design and can tilt sideways when removing the factory screw.. making re-assembly a bit of a pain. You'll need to remove the mirror assembly so you can get a better look at the square nut. If the OE square nut is stripped you'll need a replacement OE nut. I don't have those to send you, but I can get you a free replacement on the end weight screw if you need one. If so.. please submit a ticket to our customer service team of what you need assistance with and they'll get you taken care of. Here's a link to our service team to submit a support ticket: www.slingmods.com/index.php?route=information/contact

[@susangarrett9411]

Hey I have the helmet lock on the end will I not be able to keep it on if I add these to the handles?

[@Slingmods]

Hello Susan, you would unfortunately not be able to run both this and the helmet lock as they both utilize the same mounting location. My apologies.

[@stephaniewooden8555]

I ordered a set but it says "preorder" and that they won't be here until August.... sigh.. waiting is hard

[@Slingmods]

Lol. Hello Stephanie.. we do have a small shipment expected in June as well. We pad our ETA's so that we can under promise and over deliver. Hopefully we'll get enough in our June shipment to get yours to you! 😁

[@hamptonhumber2808]

Will these be able to be installed with a lid lock?

[@Slingmods]

Hello Hampton, no it would not. It would be one or the other on those two mods.

[@thomasvincent5323]

Are they available now? Slingmod cite says not until August.

[@Slingmods]

They're on pre-order.. but that ETA is padded for sure. I'm hoping to have them by June.

[@nicwill8687]

I bought these and the Spacers to eliminate my traditional mirrors but can't because without the mirrors there nothing to screw these to do now I do not need the Spacers. 😔 What should I purchase to omit the original mirrors and cap my handlebars, preferably with end weights?.. although the one's I have make 0 difference.

[@Slingmods]

Hey Nic, if you've already sourced aftermarket mirrors that do not utilize the bar ends, you can either go with our handlebar end caps here: www.slingmods.com/canam-ryker-billet-aluminum-handlebar-end-caps or you can go with our Lidlox helmet lock system. You'd need the Lidlox for use "without" the stock mirrors if you're running aftermarket mirrors. That can be found here: www.slingmods.com/canam-ryker-helmet-lock-kit-for-use-without-stock-mirrors-lidlox

[@rolandovillalon865]

I replaced my mirrors on my Ryker so how do would I install the weights with the spacers?

[@Slingmods]

Hello Rolando, The Ryker handlebar end weights have only been designed for use "with" the factory mirrors.

[@billbuschgen520]

Looks like they may block some of you mirror view?

[@Slingmods]

Hello Bill, it does a bit. Most guys are running the End Weights with our "Wide-Vu" convex mirror add on's here: www.slingmods.com/canam-ryker-convex-side-view-mirrors