Canon NC-E2 Ni-MH charger

The battery charger for Canon EOS 1D, Canon EOS 1Ds, Canon EOS 1D mark II, Canon EOS 1D mark II N and Canon EOS 1Ds mark II. It also works for Canon EOS 1V and Canon EOS 3 film cameras when using them with battery pack PB-E2.

[@СтаниславФедорчук-ш2ц]

thank you for sharing important information

[@ScottGravlee]

What does refreshing the battery do? I've got three 1DS bodies that came with batteries but no charger. I rigged up a jank charger but the camera's tell me low battery. I'm getting around 13 volts.

[@hybryd83]

It's simply discharges the battery and after this recharges it. The Ni-Mh batteries have this memory effect if they are repeatedly charged without a complete discharge. This refresh procedure can eliminate this effect. I don't have these type of batteries anymore, so I cannot measure.

[@natalieisagirlnow]

should be 14.6ish

[@TheMountain_Goat]

i'm having some problem with the charger B plug, when i plug the battery in the red LED keeps flashing Also, how long does it take to refresh a battery? the A plug works fine

[@hybryd83]

My experience is the refresh time depends on the actual health/capacity of the battery. This battery set what I've shown in the video were quite old (10+ years) and the refresh cycle lasted about 70 minutes for each battery.

[@rzober89biologia]

I had the same. It was a loose connector in my case. When I'm pushing the connector into battery it is solid red. Once I put it on the ground it starts flashing rapidly red/yellow. I put it vertically and it seems to work.

[@dps6198]

When I plug in a Canon battery the red light is solid. After 20 minutes both the red and amber light flash. This happens on the A and B side. I have a new generic NP-E2 coming from Battery Monster.

[@davepastern]

I have the same problem, no answers on this...

[@rzober89biologia]

@@davepastern I have the same issue. Did you mange it?

[@davepastern]

@@rzober89biologia dead batteries mate...throw them. Either buy genuine new ones or 3rd party (much better option). note that 3rd party battery options don't have the # of shots capacity of the genuine articles, but they are MUCH cheaper.

[@rzober89biologia]

@@davepastern I think it was a loose connector in my case. When I'm pushing the connector into battery it is solid red. Once I put it on the ground it starts flashing rapidly red/yellow. I put it vertically and it seems to work.

[@davepastern]

@@rzober89biologia I guess that is possible too.

[@kukuhpriyono4823]

I have a problem, my charger only flashes a yellow light (refresh) how can it turn on the charge, help me please.

[@borystabanets6183]

Probably a bad battery. Try charging another battery.

[@kristiandonarquiza563]

Need help here: As soon as i plug my battery in the charge light stays solid but after 20mins of charging both refresh and charge lights start tonflash about 30 times a second. Posted a video of the problem on my profile. Thanks

[@hybryd83]

Do you experience this problem with the B plug as well? Have you tried the charger with a different battery?

[@kristiandonarquiza563]

@@hybryd83 yes i tried the B side but still the same, dont have other battery to try on.

[@rzober89biologia]

I have the same issue. Did you mange it?

[@aliasobelisco]

intermittent red led is charging?... continuous red led is charged?

[@hybryd83]

When the CHARGE led is continuously red = charging the battery. When it blinks it is done, or some sort of error happened. When the REFRESH is continuously amber = discharging the battery.

[@aliasobelisco]

@@hybryd83 thank you. i got it

[@sunjob]

battery NP-3E, Li-Po mod battery pack for Canon 1D/Ds markII kzbin.info/www/bejne/d2nViIigZs-qqJY