Car Horn Fix - Peugeot 307

If the horn on your Peugeot 307 (2001 to 2008 model) is only working intermittently or not working at all, it could be a problem with the earth wire from the back of the airbag unit. WARNING: Attempt this fix at your own risk. Working on or near the airbag unit could be very dangerous so use extreme caution !. If you’re in any doubt, take the vehicle to a Peugeot dealer or garage to have the problem diagnosed. Disconnect the battery at least 30 minutes before you start, to disable the airbag system. Do not disconnect the airbag connectors and do not probe the airbag terminals or connectors with a test meter as this could risk triggering the airbag. Thanks for watching. Please comment, like and subscribe !.
~~~~ Part Links ~~~~
As an Amazon Associate I earn from qualifying purchases.
🚗 Small File Set ~ amzn.to/3oAxGGc
Disclaimer: Screwsnutsandbolts is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to www.amazon.com
All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.
© / screwsnutsandbolts 2022
Read important information below:
Disclaimer
Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Screwsnutsandbolts recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts.

[@screwsnutsandbolts]

Thanks for watching ! Please support this channel by clicking the Like, Subscribe, and SUPER THANKS buttons. Your support will help me to continue and improve my videos 👍

[@Code_ReVo]

My mother drives this car and had the same problem! I followed your video exactly. And it actually worked straight away! I thank you so much! Who knows how long it would have taken a mechanic to find this problem. Saved nerves and money, thanks to you!👍👍

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@Code_ReVo]

@@screwsnutsandbolts greetings from Germany! 🤝

[@pilgrimoutdoors-uk6177]

Why have I only just found your youtube channel? I have been hornless for 4 years with this car - I have a month off work and loads of stuff to do to the car now, thanks to you! Magic.

[@screwsnutsandbolts]

Thank you :)

[@snoopy10411]

How have you managed to get through 4 years worth of MOT tests without the horn working?

[@brucemartin8435]

Nice informative tutorial with no aggressive background music. Thanks!

[@screwsnutsandbolts]

You're very welcome. Thanks for watching ! :)

[@ifonlytimestoodstill]

Worked a treat for me this thank you! That said, the copper connector needed sanding but the wire for me was snapped off it! Thankfully, soldering the wire to the connector worked 👌

[@screwsnutsandbolts]

Well done 👍

[@pilgrimoutdoors-uk6177]

Epic! Had a dry few hours this afternoon and followed this advice, and what do you know... I have a horn again!! The white airbag wires were little tighter than in your video, so I basically used masking tape to tape the airbag to the upper wheel to give me hands free access to the wire and connection. Worked a treat. Horn now working after 4 years! Not once has it been tested on an MOT... so I consider myself lucky! Thank you, you're an absolute star! 2003 307 SW 110 HDI.

[@screwsnutsandbolts]

You're very welcome ! :)

[@daliborjankovic7947]

Thanks a lot dude. I was four years without a horn. Super easy and fast fix on my 307. God bless you 😃😄😄👍👍👍

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@Peugeot307HDi]

This video saved my days and my ass everytime I needed to blow the horn. A tip for whoever struggles with reaching to the (-) pole of the battery: I fixed this problem with a friend of mine who is an electrician, he suggested to remove the (+) pole (because it was easier to reach) and it worked real good. Only thing to notice is the reset of date and time on the screen, all the other infos are saved. Thanks a lot for the community service, really saving our pockets' weights!

[@Dzombache90]

(-) pole is also more complicated for my car, because it doesn't have a clamp like (+) does. I'm not sure if it is the same which one you remove, especialy because the video says it's the earth wire connector? I mean, it should be the same, but I don't know.

[@MegaxError]

Thank you so much for the Amazing tutorial! The mechanic I went to said the problem was probably a broken spiral or something like that and it would cost like 800€ for the spare part and the work needed. Watched your video and followed the instructions and now my horn works again! And it it was completely free! Such a simple fix and it took almost no time at all.

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@paschalis1234]

Awesome !!!!! electrician asked me 70 euros to fix the horn. Done in 5 minutes . Many thanks.

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@axyliatos]

20 years without horn. Problem solved in 5 minutes! Thank you very much

[@screwsnutsandbolts]

You're welcome!

[@jensnitsche4994]

Habe gleiches Problem bis heute, aber toleranten TÜV Prüfer...."Die Hupe sollte man einmal überprüfen! " ...aber immer Plakette erhalten. Hatte nie Ahnung, wie ich das Problem lösen könnte. Danke für dieses ausführliche Video!

[@shtrki007]

Shout-out to this tutorial, this is marvelous! I didn't had horn for 2 years, mechanics don't want to deal with this because they can't charge this, it's a small thing but you are my savior, thanks to the moon and back!

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@sarahking8819]

Brilliant video, I’ve just bought a 307sw and the horn wasn’t working (had a fresh MOT!!!), n/s wheel arch liner was loose so someone had obviously checked the horn and fuse box then given up. Took me 10 minutes after watching your video to fix it, would never have known this was the problem.👍

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@mrflibble5311]

Thanks for the video. Had the same issue with a 206. Checked the fuse ,took out the horn and put 12v on it direct and it was working . I saw your video and it was a similar issue . I cleaned up a spade connector under the airbag and squeezed it a bit with a pliers . Job done . For anyone doing it on a 206 there's one clip to be pushed directly under the steering wheel.

[@screwsnutsandbolts]

You're welcome, thanks for watching :)

[@DJdoublevision]

Thanks good to know ..looks like I'll be having to do this on my 206

[@svmei]

No annoying background music was nice, but, the silence made it seem like the airbag was gonna go off any moment and it was just building up the suspense the entire video monkaS

[@mfree9202]

Thank you, great video, very well presented. I have a 2009 Berlingo with this problem, I have to hit the horn area hard a few times to get the horn to start working. It will work after that for a day or so then stop working again. I've been wanting to take off the steering cover to take a look at what is going on but I have been apprehensive about the air bag. I will give this a go using your instructions, hopefully it will go straight forward. Further note, I had a garage try to fix this a few years back, and they replaced the squib stating it was faulty, but the problem remained. A couple hundred quid down the drain using the garage.

[@pencilheadtwo6567]

The garage servicing my 2003 Pug Partner couldn't fix the horn for it's MOT. Nervously followed your video. (Cleaned up the contact instead of screwing it in). Horn works. Cheers! 👍

[@screwsnutsandbolts]

You're very welcome, glad you got it sorted 👍

[@pele6234]

Dziś zrobiłem tak jak w przedstawionym filmie i klakson działa 💪👍

[@screwsnutsandbolts]

Very good 👍

[@hak7071]

Ça marche 👌 ça fait des années que je me passais de mon Klaxon ... je vous laisse imaginer la frustration dans certaines situations 😬😅 alors que la manip est toute simple pour résoudre ce problème ! Merci 🙏

[@screwsnutsandbolts]

You're very welcome, thanks for watching ! :)

[@adamogorman4871]

Thanks to this video I fixed my car horn without paying a mechanic!! Thank you sir!!

[@screwsnutsandbolts]

You're welcome, thanks for watching :)

[@damianhunt2187]

This fix worked for me. The bit was getting the centre/horn button bit off. I found putting it back in reverse order helped, ie side clips first then bottom clip last

[@bobspacon]

A careless mechanic cut the white wire for the airbag, the horn stopped working and another claimed it's because of that. Thanks to this video, now I know which is actually connected to the horn and airbag

[@screwsnutsandbolts]

Thanks for watching :)

[@saharalami5639]

Very interesting tuto: clear, soothing and calm. many thanks in all languages of the world

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@panchodavilla]

Worked like a charm. Cant believe I was hornless for years due simple contact issue... Good thing I did not listen to advice from service when the issue first came up, to replace com2000.

[@screwsnutsandbolts]

Thanks for watching ! :)

[@panchodavilla]

@@screwsnutsandbolts No, no, thank you for sharing the knowledge. Saving $$$ on maintenance is always nice ;)

[@njokuikechukwu6157]

Thanks a lot for this video... Had the same Problem on my 307 SW... Followed the steps shown here and its working again. Thanks again.

[@screwsnutsandbolts]

You're welcome, thanks for watching ! :)

[@acompenpakoica7935]

Very Big thanks from France and Algéria, 👍👍👍

[@screwsnutsandbolts]

You're very welcome !

[@vata1901]

A very good video. Very clear and easy to follow. Thanks man.

[@screwsnutsandbolts]

You're welcome, thanks for watching !

[@Jcg1988Giselle2012]

Muchas gracias por este video, ya estaba desesperado por que no funcionaba, y en el taller me ubiese costado una pasta, lo hice tal cual el video y funciona como el primer día. Gran trabajo!

[@screwsnutsandbolts]

You are very welcome. Thank you for watching !

[@BETFRED1981]

Thank you. The video above worked on my citroen berlingo. 👍

[@screwsnutsandbolts]

Excellent !. Thanks for watching 👍

[@toywolf-chachi]

Thanks. Apart from slightly different removal of the airbag, this was useful to fix the issue on my 2008 berlingo. Cheers 👍

[@screwsnutsandbolts]

Thanks for watching :)

[@ps-3dforgingyouridea711]

Hi Toy, I have a Berlingo 2008 too. Was it difficult to do it? Any issue with the Airbag? I am freaking out it will explode....

[@KiwiMurfy]

Thinking of having a go at my 2007 Berlingo so good to hear it's a winner

[@mustafabakalli4093]

Tausenmal Dankeschön Habe es genauso gemacht und es hat sehr gutfunktioniert. Ich fahre auch dieselbe Auto.Danke nochmals.

[@screwsnutsandbolts]

You're welcome !. Thanks for watching !

[@franciscopascualbaena]

Demostacion rapida,efectiva y eficas.gracias por compartir

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@storyfabrick7134]

Thank you, you advice fixed my horn problem, May God Bless you

[@screwsnutsandbolts]

You're very welcome, thank you

[@Bodika.]

Thank you very much. Watched your video and gathered some strengt to try fix kt myself, works like charm

[@screwsnutsandbolts]

Excellent, well done !

[@Bodika.]

@@screwsnutsandbolts do you have some video/instructions for fan/blower? Just stoped working, like he didnt have strengt to work.. automatic climate

[@screwsnutsandbolts]

@@Bodika. I don't, sorry about that.

[@retrocosas5923]

Muchas gracias amigo solucione mi problema de bocina

[@screwsnutsandbolts]

You're very welcome 👍

[@odairoliveiracursos]

Comprei uma recente é seu vídeo foi o melhor que encontrei, muito obrigado já sou seu escrito!

[@screwsnutsandbolts]

Thanks for watching !

[@odairoliveiracursos]

@@screwsnutsandbolts olhei aqui amigo, porém o meu é uma partner 2010 você tem algum vídeo explicando?

[@mole3250]

Thanks for the video! I did it according to you and it only helped when I put the airback back in and plugged in the battery so I was driving a click in the steering wheel whenever I passed the center of the steering wheel, don't you know what it could be?

[@screwsnutsandbolts]

You're welcome. It sounds like the sound could be coming from the clock spring: kzbin.info/www/bejne/gZLEe6WcmrtsZ5o

[@dieseltips]

Muy bueno gracias por el video, lo voy a hacer ahora. Por favor put some oil in the crankcase!!

[@screwsnutsandbolts]

Thanks !. The oil level is good but the oil level sensor is faulty. Sometimes it works and sometimes it doesn't :)

[@familleriviere3629]

Tanks for this vidéo ! My Horn is OK now !

[@screwsnutsandbolts]

You're welcome !

[@barrybianca]

worked for me on 307 sw 2003 diddnt see anything wrong stil try it and it worked from nothing to working completley thanks for the vid

[@screwsnutsandbolts]

You're welcome ! 👍

[@myklmar]

it was so much easier than i thought it would be. Thank you for the great video. Followed instructions and it worked!

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@KiwiMurfy]

Spot on this, all done, horn working, very happy. Thanks

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@jendrix71floyd]

I thank you so much Mr. Your explication is very good

[@screwsnutsandbolts]

You're welcome, thanks for watching !

[@Kalvis1]

60 yeara worhout horn! Fixed in 6 seconds. Thank you!

[@Rosa0527]

Very informative. Thank you very much! Informative warnings help me lowering unsure feelings. 👏👍😄

[@screwsnutsandbolts]

Thanks for watching !

[@tonbosma8347]

Just for your info some Peugeots have 2 torx srcews behind the steering wheel accessible through the small holes, no clamp in there!!! Looks to me that all with the horn function in the handle have those trorx screws holding the airbag in the steering-wheel . In fact those wheels look similar to this one, but the top of the airbag/steering-wheel is different. the airbag module (cover) bends over the steering-weel top in this model but those whit the screws have a foam like rubber that is part of the steering-wheel and a more flat airbag module, also minor wiring differences. My model has only 1 connector (orange) going from the spring clock behind the steering wheel towards the airbag module and no wires for the horn of course. You can damage this connector/wiring while poking in these holes trying to find the clamp!

[@screwsnutsandbolts]

Thanks for the info. I did state in the description that this fix is for the 2001-2008 peugeot 307 model only

[@markwilliams2830]

Very well explained,especially the safety aspect.I think the fault is probably common to other makes of cars too.Thanks for sharing.M

[@screwsnutsandbolts]

Thanks. Yeah I wouldn't be surprised. It's a strange way to connect it !

[@sebastien9227]

Merci beaucoup pour cette vidéo grâce à vous mon klaxon fonctionne de nouveau 👍🙂.

[@screwsnutsandbolts]

You're welcome, thanks for watching ! 👍

[@ArmandoGallego-yd6sj]

Fixed ! , it was a bit hard to remove the connector , my 307sw is second hand and the connector had a screw insert it !, probably the last owner or his mechanic put it in there ! ... anyhow now is working , thanks

[@screwsnutsandbolts]

You're welcome, thanks for watching !

[@johannesschmidt5605]

Ser gut hat bei meinem Wagen geklappt 😅 10 schterne für den Tipp vielen Dank

[@screwsnutsandbolts]

You're welcome, thanks for watching !

[@joanarus1441]

Your video save my Life broo thank you very much good blees you 🙌

[@screwsnutsandbolts]

Thanks for watching !

[@EXTREME751]

Tank you this vídeo hekp me to fix my 307 horn fix.

[@screwsnutsandbolts]

You're welcome !

[@cesarmar9292]

Excelente.. saludos desde argentina

[@screwsnutsandbolts]

Thank you !

[@daliborjankovic7947]

5:15 Bro, you should check oil level 😉

[@screwsnutsandbolts]

The oil level was actually fine. The oil level sensor is faulty. Sometimes the display shows it's full and sometimes low :)

[@lolowrs6798]

Thx very very much bro. It's 👌 Really good tuto👍😉

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@SofianeBensekrane]

Hello my brother. Please why i should reconnect the battery with door driver open and switch on the ignition outside the car please. I have this problem in my car. And im scary

[@screwsnutsandbolts]

It's just a precaution, in case the airbag deploys when the power is reconnected.

[@مرادشرفاوي]

ياأخي بارك الله فيك هذي مدا ونا نحاول كيفاه نفتحا

[@BigBossBossman]

Thank you so much ...

[@screwsnutsandbolts]

You're welcome !

[@sandyargo9825]

Top marks, one excellent video

[@screwsnutsandbolts]

Thank you !

[@Monilikesmusik]

Oh thank you, a very good instruction🙏

[@screwsnutsandbolts]

Thanks for watching !

[@shadenalkajmi-lo1wj]

It works ❤❤❤

[@danijelkrstic4141]

Lepo pojasnjeno detaljno svaka cast. Inace ne radi mi sirena na xsari vtr godinu dana i jace ! Kupio sam cak i novu sirenu probao opet nista. Proverio kablove da nije neki u prekidu slucajno medjutim sve je tu ok samo truba ne trubi. Moracu da otvaram volan sad nzm.ako iskljucim akumulator smem da ceprkam ili? Pozdrav iz Srbije Beograda

[@AutomotiveR7]

So informative , thank you so much

[@screwsnutsandbolts]

You're very welcome !

[@mojo888x]

is this similar on a 2004 Peugeot 406? or is there a big difference from the 307?

[@screwsnutsandbolts]

I haven't worked on a 406 so I can't be sure, sorry.

[@alfredosullca148]

Tenia el mismo problema... Y funciono perfecto 👍👍👍

[@screwsnutsandbolts]

Thanks for watching !

[@mickbones101]

Great stuff mine is now working a treat , thanks 😊

[@screwsnutsandbolts]

You're very welcome, glad it helped ! :)

[@nismogt-r3393]

Buen vídeo me sirvió de mucho y volvió a funcionar mi claxon

[@muhammadhassanasghary495]

I hope this works for me I will try it asap Thanks bro 🙏

[@screwsnutsandbolts]

You're welcome !

[@mustafaaskraba4187]

Bravo majstore

[@screwsnutsandbolts]

Thanks for watching !

[@leusgutierrez8095]

Thanks a Lot my friend !!!

[@screwsnutsandbolts]

You're welcome 👍

[@mohammedasifhassani7256]

Thank you so much for your help God bless you brother

[@screwsnutsandbolts]

You're very welcome !

[@themilktrayman7369]

Superb video, Thank You for your effort to help.

[@screwsnutsandbolts]

You're very welcome. Thanks for watching !

[@themilktrayman7369]

@@screwsnutsandbolts Actually I admit I watched it 3 times, I'm a bit slow like that but hey I did it, after cleaning I added a piece of wood jammed in between the spade clip to force its sides outward, now i have a very strong contact. Thank You I couldn't have done it without you.

[@screwsnutsandbolts]

@@themilktrayman7369 Well done ! :)

[@cristianmanica39]

Great video, thank you !

[@screwsnutsandbolts]

You're welcome, thanks for watching !

[@janandersson9646]

Tack mannen du är bäst 🇸🇪 jag 🦧

[@screwsnutsandbolts]

Thanks for watching !

[@petartomic9783]

Genius.

[@screwsnutsandbolts]

Thanks for watching :)

[@ckermo]

Great video. Just a question : why is your Airbag light still on ? It's not supposed to stay on afaik

[@screwsnutsandbolts]

The airbag light was already on before I started. That was a different issue

[@hipstarchild]

Great video. Thanks for sharing

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@javierfernandez576]

Thank you so much . Can you show us how to change the cigaret ligther ???

[@screwsnutsandbolts]

It's a lot of work. You have to take off the lower center part of the front fascia and then remove the center console, which involves disconnecting a passenger airbag sensor. To be honest, it would be easier to quit smoking ! :)

[@javierfernandez576]

@@screwsnutsandbolts thanks you

[@toonzik]

Thanks i will try that

[@thevikingoli8847]

Thank you for explaining muchos respect 👌🏼👌🏼

[@screwsnutsandbolts]

Thanks for watching ! :)

[@thevikingoli8847]

It is still not going damn, but you explanation is super where Can I find The fuse becouse I don't have the book....... I took them all out and could find a a bad one en under the hood. With kind greetings Oli

[@screwsnutsandbolts]

@@thevikingoli8847 Is it the same model 307 as the one in the video ?

[@screwsnutsandbolts]

@@thevikingoli8847 Check this link here: fusesdiagram.com/peugeot/fuses-and-relay-peugeot-307.html

[@thevikingoli8847]

@@screwsnutsandbolts your to nice, thank you may Odin be by your side. 👌🏼👍🏼

[@basemnajmeh]

Thank you very much man for video ❤😊

[@screwsnutsandbolts]

You're welcome !

[@Ppp-kk6hw]

Big up from Scotland and Will it work?on Citroën berlingo multispace 2010 😊

[@screwsnutsandbolts]

Thanks, I haven't worked on one so I can't be sure, sorry :)

[@СтанкаВрачева]

Great job sir. 100 % working 😊.

[@screwsnutsandbolts]

Thanks for watching !

[@aarongarciasachez7482]

Buen turorial muy claro gracias por la ayuda.

[@screwsnutsandbolts]

You are very welcome, thanks for watching !

[@Geoffers2244]

Thank you so much. Worked a treat. 😊

[@screwsnutsandbolts]

You're welcome !

[@TheNicolas63]

Hello Thanks you so much ☺

[@screwsnutsandbolts]

You're very welcome !

[@KhZero01]

Work perfect but I have a AIRBAG signal after that. How I can fix that ?

[@mrjones5880]

Thanks and its cool but i hate videos where they dont talk to ya.

[@tonymimo4701]

esta bien esplicado para llegar a desmontar,ok

[@screwsnutsandbolts]

Thank you !

[@jer3870]

My 107 horn keeps going. Could it be the relais of the claxon or just replace steeringwheel because of the spring inside might be broken?

[@screwsnutsandbolts]

It sounds more like an issue where you push the horn

[@sylvainseverin9280]

thank you verycvery very very much 👍👍👍👍👍👍👍👍

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

When the connection is bad, you hear a clicking sound of the horn relay or none at all? My 307 is without horn sound but I suspect it might be something else, as the relay makes a sound indicates that the button pressing seems to be working. Thanks!

[@screwsnutsandbolts]

I didn't hear anything when I pressed the horn before I fixed it

@@screwsnutsandbolts thanks for your feedback. so I guess with that my problem might be on the horn itself, not on the wheel switch. Thanks! =)

[@screwsnutsandbolts]

@ You're welcome, good luck !

[@kurd_24]

You are a genius... man.... does the wireless tape cause the car alarm to malfunction...???

[@screwsnutsandbolts]

I don't think it could affect the car alarm

[@chrisillsley2302]

Great video.

[@screwsnutsandbolts]

Thank you !

[@pixure]

worked for me! 🙂

[@screwsnutsandbolts]

Thanks for watching !

[@Soso-rw9dz]

Thanks you merci !!!

[@screwsnutsandbolts]

You are welcome!

[@CarlosGarciacsharls]

May this fix work on a peugeot partner year 2006 aswell ?

[@screwsnutsandbolts]

It may be different but I'm not sure as I haven't worked on a Partner, sorry

[@ps-3dforgingyouridea711]

Thanks, really clear explanation. I have a Berlingo 2008, and the horn doesn't work. I'm just a bit nervous to touch the Airbag. Is it safe to work around it if I unplug the battery?

[@screwsnutsandbolts]

It should be safe but be very careful. Make sure nothing electrical gets anywhere near the airbag contacts when you unplug them. This is from the 1996-2005 Haynes Berlingo Manual so I don't know if it's the exact same with the 2008 model : a) Switch on the igniton and check the operation of the airbag warning light on the instrument panel. The light should illuminate when the ignition is switched and then extinguish. b) Switch off the ignition. c) Remove the ignition key. d) Switch off all electrical equipment. e) Disconnect the battery negative terminal f) Insulate the battery negative terminal and the end of the battery negative lead to prevent any possibility of contact. g) Wait for at least two minutes before carrying out any further work. Wait at least ten mlnutes if the airbag waring light did not operate correctly. Good luck 👍

[@ps-3dforgingyouridea711]

@@screwsnutsandbolts wow, you are a star. What's the d) Switch off all electrical equipments? Is this i.e. Enything connected to the cigarette lighter or similar? If you disconnect the battery there shouldn't be any other source of electricity in the car? Am I wrong?

[@screwsnutsandbolts]

@@ps-3dforgingyouridea711 Probably switch off lights, wipers etc. before disconnecting the battery. I not exactly sure why but better safe than sorry :)

[@screwsnutsandbolts]

@@ps-3dforgingyouridea711 By the way, This is is what it says about the re-activation of airbag system. To activate the system on completion of any work, proceed as follows: a) Ensure that there are no occupants in the vehicle and that there are no Ioose objects around the vicinity of the steering wheel. Close the vehicle doors and windows. b) Ensure that the ignition is switched off then reconnect the battery negative terminal. c) Open the drivers door and switch on the ignition without reaching in front of the steering wheel. Check that the airbag warning light illuminates briefly and then extinguishes . d) Switch off the ignition. e) If the airbag warning light does not operate as described, consuIt a Peugeot/Citroen dealer before driving the vehicle.

[@ps-3dforgingyouridea711]

@@screwsnutsandbolts f) if the airbag warning light does not operate has described..... BANG too late..... Thanks mate, really appreciate your help. I will give a go as soon as I have time. Thanks again, Best Steve

[@resulgon7965]

hello, first of all, thanks for the video, my car is citroen xsara, the horn works in the off position, but it does not work in the open position, I would appreciate it if you could help me.

[@screwsnutsandbolts]

You're welcome. I haven't come across that problem to be honest. I'm not sure why that could be happening, sorry

[@resulgon7965]

@@screwsnutsandbolts ok thanks