Carburetor Installation Is Easier Than You Think!

Don't miss a thing! Subscribe Now! bit.ly/2kzUdzB
Every now and then you'll have to pull the carburetor off your bike. We've got you covered with a few simple tips to guide the process. These steps will cover most of what you'd encounter on a either a 2 stroke or 4 stroke. A fuel injected bike has a bit more wiring but accessing the throttle body is a similar procedure.
-Cameron
ReVive Moto: www.revivemoto...
Need Tools? www.amazon.com...
Facebook: / revivemoto
Instagram: / cameronniemela
Tools I Use:
Scissor Lift: amzn.to/2xH1pkn
Dewalt Impact Driver: amzn.to/2wDxAEz
Tire Levers: bit.ly/2wX88JX
Spoke Wrench: bit.ly/2vBtn0c
Tire Change Stand: amzn.to/2wPFIlz
Wheel Truing Stand: amzn.to/2wPC7Ea
Crankcase Splitter: amzn.to/2wPTCV0
Circlip Pliers: amzn.to/2gn4u5G
Exhaust Spring Puller: amzn.to/2wfiUKx
Torx Bits: amzn.to/2wlHcBj
Allen Bits: amzn.to/2wlBTlh
Torque Wrench: amzn.to/2vGzz6x
Impact Screwdriver: amzn.to/2iDBwzg
Bel-Ray Waterproof Grease: amzn.to/2iBXRNz
Y Handle Tool: amzn.to/2wQ1Axt
Bearing Puller: amzn.to/2wPOn7x
Cleaning Supplies:
Aluminum Cleaner: amzn.to/2wld1dn
Degreaser: amzn.to/2voFxxx
Camera Equipment:
Canon 80D: amzn.to/2vlPXOk
Flexible Tripod: amzn.to/2vmj9F3
Tripod: amzn.to/2vm6NfT
Looking for a way to support the channel? Use the affiliate links below to make your purchases on eBay or Amazon.
Amazon Affiliate Link: goo.gl/WeGM3v
eBay Affiliate Link: goo.gl/EWFb5u

[@blazbencic5453]

i love your videos, i have a 2003 cr 125 and im new to dirt bikes, i had mopeds but there is a big difference so by watching your video i see the steps, thx

[@CameronNiemela]

Thank you so much for watching!

[@smooverider2777]

You save my life bro.. best vid ever.. thanks for being simple and fast

[@Fattymane]

These build videos have really been helping me out thank you 🙏

[@thailandmopedadventures611]

THANK YOU - saved me a lot hassle regarding the Airbox Installation without removing the Sub Frame😢

[@marlopatron2656]

Absolutely no expaination. He just says, route the cables back. Or connect te fuel lines. If I looked up this video means I don't know how to install it. Tell me which line has to connect where and what it does. I may be logical for you, not for mpsomeone who searches for a vid like this.

[@mariokill719]

There is only on petrol line the rest of them are for over flow and breather lines they don't connect to any thing just go straight down 👇so the over flow goes on the ground rather then your swing arm witch would fuck up your linckig Bering's and seals etc

[@dylanbrokelc]

if you can’t take a carb out and put one back in your actually slow.

[@jaredbulock]

​@Dylan Taylor what if it didn't have one to take off New motor fresh out the box.

[@pr0pay3r]

@@mariokill719 shut up ur so stupid😭

[@thatonescrambler]

2:48 but I'm big stupid and have no idea where any hose goes

[@mariaguevara2647]

Thank you so much for the video. Om so glad you thought of INSTALLING of carb. Everyone has REMOVAL of carb. Again thank you. The.video is awesome. God Bless.

[@CameronNiemela]

Thanks for watching!

[@bryce099]

Can you remove and install a new needle jet without taking the slide completely off the bike?

[@hammer5104]

bruh this shit looks easy as hell or at least u made it look i need a 2006 kawasaki klx 125 carb do u know where i can find one?

[@ZaddyZandee]

Im able to get the carburetor out and everything, but im only confused on where my tubes/hose go for the gas, if you understand what im saying? i have a suzuki drz 125cc

[@jc3702]

Hey, how do you know how to get the right carb???

[@dillonmelin7564]

most sites have something to confirm your make and model is right for the part

[@useribp]

Can i put my carburetor head down , what u think can it work because its not the original one and i need to do an adaption What u think ?

[@johnnyram518]

Hey I have an old 125 4 stroke that I was cleaning the carb on and it seems to be starting up real good but my carburetor vent hoses are straight PISSING gas when I reconnect my tank and turn on my fuel petcock . What do you think is going on that so much fuel is flowing right out my vent hoses? It feels like I did something really stupid that I'm forgetting, but I can't think of anything! I have my jets back in place and everything seemed to be tightened down real good. Any advice would be much appreciated, thanks

[@Zachry86]

Float valve is not closing. Probably bent it a little. Or maybe the floats are not moving correctly. Open the bottom end and check. You can test the valve functional by blowing in through the fuel port while moving the floats. Should close completly

[@turbotune9775]

Thank you !

[@hyposez1129]

Question i have like a white thing on top of my engine head on my dirt bike is that spark plug and then next to it is green cable or like pipe or smh so what is that for and im pretty sure my bike has carburetor not fuel injecton and also its oil cooled

[@Lisa-nz9bq]

Great video!! Very informative and interesting. Keep up the Great work Man!! Thanks

[@CameronNiemela]

Love to see people find the videos helpful! Thank you so much for watching and subscribing!

[@Motomarvation]

Damn! attaching the air box boot to Carb is impossible on my Crf250r! no room, guess ill take of the top shock bolt like you did. 😁

[@CameronNiemela]

If you use a silicone spray or lube of some sort it'll slide on easier. If it's still too difficult you can take the shock off and that'll give you more than enough room.

[@caseymoto]

MARVINS_MANCAVE seriously .. I’ve been trying to get my crf250x air boot on the carb for like 2 days now

[@positivexp2820]

been watching for a while now youve gotten alot better in front of the camera still alittle awkward sounding but keep it up and improvment shall be seen love your videos dude

[@G6Emaniac]

I got a new carbi and it’s the same size as my old one but I need to change the spring and everything

[@albertomendoza4812]

Spaceman 04 same bro

[@1815cct]

Thanks brothaa

[@oldguyjohnretrolifestyle9281]

Can you make a Mikuni 26 mm carburetor video showing how the vent tubes are connected for the Predator 212 horizontal shaft 6.5 HP motor? The MIKUNI 26mm mod for the Predator 212 has two vent ports and a main gas port being on the upper half of the carb, I'm losing all my gas leaking out of a brand new MIKUNI 26 mm carb that bolted directly to my Predator 212 Pocket Harley minibike,(when i first found that Harley pocketbike, had no engine, so thats where the Predator 212 replaces the too small weedeater kiddie engine) which of the 3 ports on that MIKUNI 26mm carb is the gas line, and can one of the other 2 ports not be used like maybe the port on the very bottom of the carb be blocked off?

[@zanesilvester1499]

Nice mate!

[@markwinchester3005]

Thanks helped alot!

[@Luui2x]

4mm hose line it’s valid ?

[@jordanv7903]

your content and devins content is so good

[@braleyshardwoodcustoms8584]

Thanks

[@williamgannon6132]

What year is the bike and what cc

[@kimwedding1964]

Do u have a video of U putting on a newer front fender on your 2007 honda cr125. I have a 2007 honda cr125 and want to put on a newer front fender. Some videos show that U need to drill 4 new holes and other videos show them only needing to drill 2 new front holes, on a 2003 honda cr250. I dont want to mess up a new fender, so any help videos or pictures would be appreciated

[@CameronNiemela]

I don't have a video on that yet but that's a possibility in the future!

[@jollyshrimpo]

Was looking for your vid of this lol who could explain it any better

[@TuneInBurnOutTV]

Good video man!

[@CameronNiemela]

Thank You!!

[@Arunry17]

Yo, you need some 4 stroke to work on imo. It would be cool to see for example rebuilding a water pump on crf 250 10-17, with mechanical seal. I have't seen any on youtube.

[@CameronNiemela]

I'm sure I'll run into a situation where I'll make a video on that. Thanks for the suggestion.

[@EthanAdey]

Lmao, why tf are new bike so hard to work on? 💀 mine you don’t need to take anything off to get to carb (maybe the side fenders)

[@ct9020]

Where did you buy the carburetor from?

[@burger5093]

to me,you didnt help or explain JACK! no hose reassembly/explaination,no choke reinstallation/explaination..no air or exhaust comments,what did you do besides fly the colors or you bikes body kit?

[@finisher8783]

Hey can I just replace the carburetor when my bike bogs ?

[@special_kenny4247]

I wouldn’t. carburetors can be super frustrating to pull so many times just to adjust your floats again.. I would pull it once look at every jet, soak em in carb cleaner over night. Adjust the floats a little(also could just be your pin) if that doesn’t work.. don’t waste your time and buy a new one.

[@yaboityler1]

Not when it's been sitting for 5 yrs under a house

[@toddlk1867]

Because my fuel injected yzf 250 totally has a carburetor...

[@sean.g4516]

U jst talking an speeding through everything how can anyone understand what's going on all these forward ass videos