Carburetor Tuning with a Vacuum Gauge | Edelbrock Carb Tuning | Dodge D100

The 1975 Dodge D100 project hot rod truck has run rich ever since I got the truck. Today I will be using a vacuum gauge to see if I can't dial in the air-fuel mixture on the Carter/Edelbrock carb...wish me luck!
D100 Videos:
• 1975 Dodge D100
VW Beetle Videos:
• 2001 VW Beetle
Charger Videos:
• 2017 Dodge Charger
DIY Projects:
• DIY Home Projects
Fitness Videos:
• Fitness
You can always find me here:
Webpage: www.wjm-industries.com/
Facebook: / wjm.industries
Instagram: @Moonbuilt
Twitter: @BuiltMoon
Tools Used For This Build:
- Vacuum Gauge Amazon amzn.to/3qbPaui
- Timing Light Amazon amzn.to/3ncjRNP
- Edelbrock Carb Rebuild Kit Amazon amzn.to/3bp8UT6
eBay ebay.us/gKCkKg
- Holley Fuel Pressure Regulator Amazon amzn.to/3ebPFOL
eBay ebay.us/KymZan
What I Use To Film:
Canon EOS M50: amzn.to/3aRNRbw
DJI Osmo Action: amzn.to/3aR2E6x
Zhiyun Smooth 4 Gimbal: amzn.to/2YKrkto
Rode VideoMic Me-L: amzn.to/3pUx1RI
Rode VideoMicro: amzn.to/3nBqFng
Rode Wireless Go Wireless Lavalier: amzn.to/2RoROO3
Vijim LED Video Light: amzn.to/3gW5mLV
Thronmax MDrill Zero Microphone: amzn.to/2ZR23cK
AmazonBasics 60-Inch Lightweight Tripod with Bag: amzn.to/2ZxEVzP
Vastar Smartphone Mount: amzn.to/2NE5JMp
eBay - ebay.to/3CE3bo4
Amazon - amzn.to/3j769Zo
Automotive Parts at Jegs - jegs.ork2.net/jWX4rb
Custom T-shirt Designs at Printful - bit.ly/3pSuebT
Disclaimer: Some of these links are affiliate links where I'll earn a small commission if you make a purchase at no additional cost to you. This helps support the channel and allows us to continue to make videos like this. Thank you for the support! All opinions are my own and presented without editorial input from outside sources.
Disclaimer:
Due to factors beyond the control of MoonBuilt Garage and WJM Industries LLC, we cannot guarantee against improper use or unauthorized modifications of this information. MoonBuilt Garage and WJM Industries LLC assume no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. MoonBuilt Garage and WJM Industries LLC recommend safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of MoonBuilt Garage and WJM Industries LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not MoonBuilt Garage or WJM Industries LLC.
Produced and owned by WJM Industries LLC
#MoonBuiltGarage #D100 #Mopar #1stgen #Muscletruck #hotrod #stroker #hotrodtruck #dodge #408stroker #417stroker #408ci #417ci #strokermotor #dodged100 #V8 #moparornocar #dodgetrucks #dodgeporn #dodgebuilt #builtnotbought #garagebuilt #truckbuilds #d100brotherhood #dodgebrothers #moparnation #rattymuscletrucks #rattymusclecars #moparmafia #Americanmuscle #trucklife #garage #garagebuilt #garagelife #garagefun #garagenight #oldtrucks #projectcar #projecttruck #streettrucks #garagefun #Workshop #Welding #Fabrication #tools #Hotrods #Musclecar #Musclecars #Hotrodsandmusclecars #Hotrods #Homebuilt #garagelife #oldcars #oldtrucks #madeinusa #americaclassic #oldschool #horsepower #streettrucksmatter #badass #patina

[@einstein3509]

Did you put lighter springs in, on the needles. If they are the stock carb spring they may be to strong for the vacuum you have. That will make it run rich. I say this because of my experience with my Edelbrock. My vacuum is around 14 and when I slid the needle caps to the side while the engine was running they were bouncing up and down. Made my engine sound like I had a bigger cam. There wasn’t enough vacuum to over come those springs. So I bought the spring kit from Edelbrock and kept installing lighter spring until the needles stayed down at idle. Then it ran leaner and smoother. The trick it to install the strongest spring that your vacuum can hold down. So the second your engine starts to loose vacuum from pushing on the throttle those needles will spring up letting gas in.

[@JeLifeCoach]

This is spot on. I was about to type this exact thing.

[@JeLifeCoach]

Secondary recommendation would to go to a thicker metering rod next. If that doesn’t work, go stage 1 lean in cruise mode w a jet change on the primaries. The secondaries on these seemed to be tuned spot on most of the time. Simply adjust the flap for secondaries for more spring tension and on hard WOT shouldnt be any bog.

[@tomnoller2427]

That was very helpful! Thanks so much!

[@MoonBuiltGarage]

Glad it was helpful!

[@tyrantwitness2482]

Power tune timing first! Advance until it pinks up hill in high gear and back off one nudge so it stops pinking. Then start on the carb.

[@dirtmcgirt0420]

Edelbrock recommends 6psi to maybe 6.5 so you're right on.

[@josecuevas8602]

The fuel level affects the entire fuel curve, high fuel level enrich the fuel curve, low fuel level dose the opposite, leans the fuel curve.

[@rustynutz7158]

Which port did you connect the vacuum gauge to??

[@MoonBuiltGarage]

Manifold Vacuum...the port on the lower right side of the carb as you're looking at it from the front...If you're still unsure of which ports are which (manifold vs ported) you can Google an image for the vacuum ports of an Edelbrock

[@juanbasulto4021]

I'm in Vegas, could you help me adjust my friends nova

[@MoonBuiltGarage]

Possibly....might make a good video...

[@gearheadmoff1232]

Where is your garage located...?

[@MoonBuiltGarage]

Right now...about 3 feet from Hell....Also known as Las Vegas

[@jts9120]

@@MoonBuiltGarage I thought hell was Arizona hahaha

[@dirtmcgirt0420]

@MoonBuilt Garage you guys must have never been to the depths at the bottom of hell named Atlanta Georgia 😔

[@CharlesFockaert]

vid more on setting float levels than engine tuning

[@MoonBuiltGarage]

That is part of carb tuning 🙄

[@CharlesFockaert]

@@MoonBuiltGarage your title reads: "Carburetor Tuning with a Vacuum Gauge " I just adjusted the floats in my Edelbrock 1406 and don't remember using a vacuum gauge to do so. Thanks for taking the time to upload your videos.

[@MoonBuiltGarage]

@@CharlesFockaert Did you watch the whole video? It isn't worth taking the time to check your carb setup with the gauge if your floats aren't adjusted right...You'll end up chasing your tail if other parts of the tune aren't set up right

[@njorogekiarie-PPS]

Has anyone tried deleting the float and maintaing the fuel pressure to the disired level