Cross RC WT4 Unboxing & Build The World's Most Realistic Tow Truck |

[@racecar021872]

How do you program the 3rd channel for the bed to move up and down and slide? Also how do you get the headlights to work? I have mine all assembled and driving but have these two problems i am dealing with. Just need some help.

[@stephenkelly8065]

Hello, thanks for the build video. I have just ordered one along with a third party sound unit. I liked your modification of the temperature controlled fan. Could you tell me what size it was please ? I could do with getting one whilst the kit is in transit. Many thanks, Steve. U.K.

[@CarsTrucks4Fun]

40mm

[@stephenkelly8065]

Thank you very much for the swift reply and information. Good luck with your channel. It’s nice to see someone actually building something for a change, rather than just pulling off a box lid and saying “look what I just bought”! Keep up the great work. Thanks, Steve.

[@bradkalman2353]

Do the leavers actually move up and down and work at the electronics?

[@CarsTrucks4Fun]

no

[@boduke9428]

This was the best. Then the Redcat COE hauler came out. Even without a functional roll back bed, that beautiful body makes up for a lot. Both are equally useless off pavement.

[@Reindeer911]

You did a nice job on the assembly. Looking forward to seeing you take it for a run!

[@CarsTrucks4Fun]

Thanks

[@ungurdani8346]

Salut my friend super car super video subscribe subscribe 👍👍🚗🚗

[@andrewrichey7374]

Wow is she a beauty, great job on it. I’ll be watching for that video like to see it in action, until next time peace and chicken grease 😁👍👍😎

[@kjflyte5088]

Cross rc , i wish i could never get recommendations for their products, because they are over priced and really un reliable..great for shelves.. about it.

[@Scottrc]

Wow nice wish mine turned out on my CROSS RC WT 4x4 LESU transmission ?

[@new.handle]

Nice paint job and build. All is needed is to set up end points for steering and gear shifting servos.

[@trentongardner2021]

Question sir! I have a cross rc wt4 and cant figure out where the little motor for the engine belt is supposed to plug into. Any help would be greatly appreciated!! Love your videos and your builds!!

[@CarsTrucks4Fun]

So many rcs in hands right now. Can you send me some photos by email or facebook. My social links are in the description

[@jsefrcop.d.7103]

I loved that work and dedication but now that I have seen it I would prefer to buy it assembled. Beautiful WT4 crossRc enjoy it 👍💪☕

[@CarsTrucks4Fun]

Thanks

[@SGLastMileFails]

This video was randomly recommended to me. I clicked on it, then turned my back to the monitor, to grab something out of a drawer. After the first 20 seconds, I thought I accidentally clicked on a Borat video.

[@CarsTrucks4Fun]

😁😁😁😁😁😁

[@419crawlers]

Would you recommend this over the traxxas? I love the looks of the cross over traxxas

[@andrewrichey7374]

Wow that’s just outstanding, this is the beauty of this awesome hobby, watching now appreciate you sharing

[@kennethoakman4198]

what RC transmitter/receiver was required for the truck? Did you purchase the sound unit from crossrc?

[@CarsTrucks4Fun]

No sound unit yet. The transmiter i use is a Flysky fsg7p. Thanks for watching

[@BoylstonBobby]

I’m really impressed by the content, level of detail and video recording that you put into your video. This is a pretty complex build by comparison to a lot of kits, but you hit all the phases of construction showing clearly the build sequence and how the components come together. A little more explanation regarding the electronics would have been helpful, but overall nicely done my friend.

[@RRCCONSTRUCTIONMININGREC-tl8yf]

AWESOME TRUCK THX FOR THE SHARE.😊😊👍👍🚜🚜🚛🚛🚚🛻🛻🚙🚘🚙🚗🚖🚕

[@hotsaucequenga9089]

Where do you run or hide all the wires for the different lights. For some reason this is the only thing that has me stumped

[@CarsTrucks4Fun]

Under the seat. But i need to cut some because they are to long

[@kerrieschneider945]

Quick question. We have just about finished this build but we have hit a snag. Can you think of a reason that the bed wont slide back and forth? It will go up and down but acts like it is stuck going back and forth. Any advice would be appreciated! My husband also sent you an email.

[@CarsTrucks4Fun]

The screws off the sliding bars are to tight

[@kerrieschneider945]

We loosened those screws and the motor will work independently but when we hook it to the spindle it will move only a couple centimeters and stop.

[@CarsTrucks4Fun]

@@kerrieschneider945 send me some photos or videos to my email

[@BoylstonBobby]

Howdy - having the same issue with mine - works great without the flat bed, but not with it. I have tried adjusting the set screws on the rails many times but still the same issue. Have you had any luck with yours?

[@Markooboy]

Hi can you tell me what servos to buy for this kit?

[@CarsTrucks4Fun]

Its on the video discription

[@Markooboy]

@@CarsTrucks4Fun Hi I checked and no details in your description about the servos used. If you could update that info it would be appreciated.

[@stephenkelly8065]

Hello again sir. I am well into the build of my truck, however I was looking over the wiring and I can see no way of powering the unit up ? Surely it doesn’t use the receiver to power up the rear bed motors ? Scratching my head as the instructions are very poor ?! Also the distribution board from the receiver has inlets and outlets on the same side, top and bottom, which is which ? Hopefully you can give me a few pointers to be able to get it working as I don’t want to do any damage to any of the electronics. Many thanks, Stephen.

[@CarsTrucks4Fun]

I will upload a video with something i need to fix. I i will show that point. Thanks for watching

[@stephenkelly8065]

@CarsTrucks4Fun wonderful, thanks very much. I just connected channel 3 via the supplied cable to the rear board that supplies the 2 lift/slide motors and light, it seemed completely dead ?! The only thing that occurred to me is that it may need to be in place under the lift motor to be able to detect the end points somehow ?? I will have a look at your video to see if I am doing anything wrong ? Still don’t like the idea of the motors being powered by the receiver power throughput though, or am I wrong ?

[@stephenkelly8065]

Just an update ! I don’t like getting beaten, I upped the voltage into the receiver to exactly 6 volts, hey presto, everything burst into life !! That would be a handy bit of information to add to the manual, plus having to fit an extra cable up the chassis and another flexible on for the winch unlike leaving it to the last page to tell you ?! Could do with a instruction re-write.

[@gabrielpichardo1492]

You should put thermal paste on that heat sensor so it can get a better temperature reading. Great job on the build though, what an awesome truck!!!

[@jaredsay3331]

I want to see the WT4 next to the trx6 Hauler

[@zane9785]

Awesome and new subscriber

[@CarsTrucks4Fun]

thanks

[@Cbam871]

Sick truck. Id put more lights on it

[@iandingle1417]

Thank you. Very good review well done.

[@CarsTrucks4Fun]

Thanks

[@gbresaleking]

I wish I could afford a cross rc vehicle, you did great but i think since its a work truck it needs some weathering done

[@iandingle1417]

Hello can you say where you put radio gear speed controller. Thank you.

[@CarsTrucks4Fun]

In the front

[@CarsTrucks4Fun]

Under the hood theres a place for it

[@OberlandRC]

You did an amazing job! Great video!

[@CarsTrucks4Fun]

Thanks

[@bradkalman2353]

The zoom chat is on Tuesdays at 9:30 p.m. North America eastern time and Thursdays the same time.

[@brianargo1659]

As cool as that thing is. I hope that's a dead battery that ur using because that bed is way to slow. Is there a way to get more speed out of the bed function?while using that motor?

[@luisrodriguez-jx8mk]

what is not included on the box?

[@CarsTrucks4Fun]

Controller, reciver, esc, servos

[@andyb9994]

Looks great 💯 lots of work!!!!!

[@TasosX]

A video no one can stop for any reason. Great job my friend.

[@CarsTrucks4Fun]

Thanks

[@vmrp071]

Está fabuloso Já decorei o número de telefone para quando o meu carro avariar. Magnífico trabalho.

[@OGRadGrow]

Nice 👍🏾

[@johntconnellyjr4354]

I didn't get a driver or banner

[@kjflyte5088]

Way too much work for a shelf queen..

[@workingclassperson2124]

So awesome 👏🏽

[@TrokaRC]

Awesome rig. Mucho detalle.

[@CarsTrucks4Fun]

thanks

[@JoeOvercoat]

Magnificent!

[@CarsTrucks4Fun]

Thanks

[@luisrcshop]

Amazing❤❤❤❤❤❤❤

[@CarsTrucks4Fun]

Thanks

[@luisrcshop]

Obrigado!

[@CarsTrucks4Fun]

estás louco... obrigado pelo apoio

[@BlackSeaRC]

Another great truck from Cross-RC with a huge amount of detail and functionality, plus a pretty reasonable price as well. I suspect you will need to remove some parts from the leaf springs to make the suspension softer. It will be interesting to see how it performs on rough ground but in reality it is probably better suited to fairly smooth terrain.

[@luisrodriguez-jx8mk]

what is the price? us dollars

[@BlackSeaRC]

@@luisrodriguez-jx8mk It is 660 USD for the WT-4 kit at Cross-RC USA.