Hello! The new Red Mean Machine easily doing the job. Greetings from Portugal.
@eatingamandarin2 ай бұрын
Transferring power to the ground is the challenge. How do you determine the necessary depth? And then how do you measure the benefit of this operation?
@prinefarms41276 ай бұрын
The new 715 Quadtrac is a beast!
@John-nc4bl6 ай бұрын
Thanks for your impressive vide The 715 could probably pull another 3 shanks.
@farminelectra6 ай бұрын
Not at 16 inches. Had to bring it out to about 12 or it would just slip.
@lfeco6 ай бұрын
You could see a bit of slippage, I'd guess the snow doesn't help. Surprised to see the 3 pt hitch.
@armchairgeneral75576 ай бұрын
Yeah I was wondering if another shank could be added then I saw the tracks slipping a bit. Those rippers are a hard pull. Engine power is there though.
@jonnykerley2 ай бұрын
You need a John Deere 9RX 830 then!
@jamesbarbour84002 ай бұрын
That's a big old assed hood on that thing - must be a massive engine in below it. Despite how deep the ripper is, and the number of shanks, the tractor hardly seems to be breaking a sweat. Engine revs sound comparatively low too - should save on fuel useage.
@TFunguy106 ай бұрын
I love ripping
@paulpence88955 ай бұрын
What, at idle... LOL
@Hermiwalle6 ай бұрын
why are you going so slow? it must be able to pull it faster with over 700 hp.
@farminelectra6 ай бұрын
Traction/slip
@Hermiwalle6 ай бұрын
Can it be weighted down more?
@fabianbeuche44536 ай бұрын
@@Hermiwallefrom 30,5t up to 34,5t it is possible
@gregjames50706 ай бұрын
Comments like this crack me up. They’re ruining it 16 inches deep. See the wave and ground breaking up behind the ripper? There’s a lot of compaction. We run a 9 shank on our 620. Some of our fields it plays with it. Some fields it’s all it wants.
@Hermiwalle6 ай бұрын
@@gregjames5070 forgive my ignorance. But 775hp is 775 hp. he stated they were traction limited. Altough it should be able to pull it faster anyways even if the slip increases.
@froggienm716 ай бұрын
I'd be more impressed with it pulling an 11 shank ripper
@timtorkelson72016 ай бұрын
Partially frozen ground to some extent? Sure it would pull 11 just as well!
@farminelectra6 ай бұрын
Depends on depth
@John-nc4bl4 ай бұрын
Rippin semi-frozen ground is not the smartest idea and that is one of the reasons for track slippage.@@farminelectra
@debi52925 ай бұрын
A twin track of the same HP would run away from this. Why? just count all the gear boxes from the engine to the tracks. I bet these 100HP shy of pull at the draw bar. Good pan rig, not good for farming.
@smylebutta72505 ай бұрын
🤡🤣🤣
@debi52925 ай бұрын
@@smylebutta7250 for some people ignorance is true bliss. words btw trump emoji's every time.
@robertbanik78792 ай бұрын
The 865C was originally planned for this ripper, it only spins with full ballast and is unsteerable
@debi52922 ай бұрын
@@robertbanik7879 If it weights around the same as the 4 track pos you're a liar.
@smylebutta72505 ай бұрын
Case IH not Case.
@gorangoran63354 ай бұрын
Compression springs on the ripper, bad engineering.