Case Backhoe Transmission Problems

[@manuelbenavidez7387]

Thank you for the information I'm going to work on mine it's working good but still going to work on it thanks again

[@abikerinpa]

Keep the videos coming my new friend ! ❤😎🍺

[@paulsequipmentrepair823]

Thank you! I will continue to make videos.

[@abikerinpa]

My uncle had one one of them backhoes as well and his torque converter went out on his … replaced it and off he went 😎

[@MustAfa-vp4kp]

What's the transmission oil shoulf be used in hot areas

[@andrewsmith9980]

I was hoping to see the oil fill and oil level screw if it has one How often should the fluid be changed Thanks

[@paulsequipmentrepair823]

The backhoe has a transmission fluid level dipstick. I believe Case specifies every 1000 hrs. Depending on how much pushing and driving you are doing you may want to change it more often. Make sure to inspect and clean your suction screen when you change fluid as well.

[@Chad_Heishman]

Do you fill it threw the dip stick hole?

[@renatoperez8392]

Awesome Work

[@jackmurdock592]

i recently bought a 580 super L and I am having a problem with the brakes I don't have much brake pedal but it will pump up. The emergency works fine and when it on I have lots of break pedal. Thanks for any help

[@jonathaneldridge5932]

ive got a case 650D dozer thats building up pressure in tranny and blowing fluid out the dipstick any thoughts to what may be causing it? runs and pushes fine first couple hours then starts to get hot and wont hardly pull, its had the transmisson replaced but didnt fix problem any advice would greatly help

[@michelgrenier1878]

By the look of the oil filter the clutch plates are done .

[@paulsequipmentrepair823]

The clutch plates are definitely coming apart.

[@cjdowndemocrats6746]

I’m looking at buying a case 680E with air brake issue any idea how to check extent.

[@michaelwalsh9145]

If it won’t climb a slight incline in 2nd gear I doubt you’d move any earth with it.

[@joeculwell3246]

I live in Poland and have a 1997 Case 580 SLE. I want to change the transmission fluid. I am having trouble finding the original case fluid. All that I can find on the internet is Case HY-Trans fluid. This is not Dexron but something different. Can you tell me exactly what this fluid is? The agro stores here all have Hy Trans fluid but I want to make sure that I get the same fluid. Thanks

[@paulsequipmentrepair823]

Hytran should be the correct fluid for that machine. I will have to double check with the service manual though. Thanks

[@magdalenoestupinan5526]

Thank you for you video I,CASE BACKHOE 580l The transmission is leaking oil, how do I fix it?

[@paulsequipmentrepair823]

It depends where the leak is. It could be a line or a seal. You would need to find out exactly where it is leaking.

[@tonyservello1056]

I change my oil from a case 780 backhoe, shuttle shift 2 speed last year and it hasn't been the same since. There was no metal particles that I could see and 3/4 of a bucket of oil came out and I filled it with almost the same amount after checking level. It would take a long time to engage and now it won't engage forward or reverse. This week I drained the oil again and it was frothy and dark grey, no metal particles that I could see. Only 2 gallons came out and I am stumped as to why this happened. I did not fill it yet because I don't want to waste the Hitrans oil I have until I find out what is going on. Any thoughts.

[@paulsequipmentrepair823]

It sounds like a low fluid level issue. I would look it up to be sure but I believe that takes around 5 gallons. The frothy could indicate low fluid level causing aeration, of course there is other variables or causes. I would definitely be looking for any leaks, the fluid is going somewhere and to diagnose it you need to find out where.

[@vacuumunit]

New Subscriber 🙂

[@paulsequipmentrepair823]

Thanks for subscribing!

[@thomaslibetwa9779]

Morning everyone. I have a case 580 super r backhoe.i can go forward but can't move in reverse. asking for help

[@paulsequipmentrepair823]

How old is your 580? Is it a L, M,N, etc.? Depending on your model I would check the electrical circuit from the FNR lever to the solenoid. Fluid level or filter condition would likely not affect only one function.

[@thomaslibetwa9779]

@@paulsequipmentrepair823 thanks.i kept checking yesterday and found two cuts.at solenoid and the fuse harness."sabotage" kkkkķ.apparently.worked just upon joining.....confused as I parked it working other than oil change and motor sub overhaul. Thanks thanks

[@raolinfantone9585]

Sir how many liter u pot on hy trans

[@paulsequipmentrepair823]

I'm sorry, I don't recall. I would need to look it up.

[@williamreese2477]

You didn't clean the vent on top of Trans. That's why it has rusty fluid from condensation and lack of service

[@paulsequipmentrepair823]

It definitely has a lack of maintenance. It was missing the dipstick until I talked him into replacing. The oil is full of clutch material.

[@michaelwalsh9145]

@@paulsequipmentrepair823 what happened after? Definitely needs a transmission rebuild and if he’s lax about transmission oil he probably did the same with the brake and hydraulic oil

[@paulsequipmentrepair823]

@@michaelwalsh9145 He is still currently using the backhoe for digging, but for pushing dirt it is seriously limited. He was talking with me about rebuilding the transmission.

[@allenmeierotto5035]

@@paulsequipmentrepair823 I strongly suspect the transmission charge pump has failed, fwd/rev clutches are almost certainly smoked as well.

[@yopage]

My 1981 case 580c is doing the same. When I get on it hard to push dirt the trans stops letting it go forward or backward, I changed the fluid from the little oil pan, and cleaned the permanent filter in the oil pan. It worked for a while, stopped again after I pushed hard. But there is a fluid plug on the torque converter that you have to line up in a little hole to get to. Whats worse, I can't find a wrench to fit it correctly. If I'm lining up the right plug in the open, it's only 1/2, seems small for a fluid plug.

[@larryburns4605]

He went a few transmission services too long

[@jimmywells33]

I'm surprised the owner didn't change the fluid and filter on his own before calling out a very expensive road mechanic. It looks like there was massive water intrusion into the case. Other than a missing dipstick or something; how would it get in there?

[@paulsequipmentrepair823]

He called me because a lot of owners and operators don't know how to maintain their equipment. I try to show my customers, buy some would rather have me do it.

[@ondrejmasek5535]

Big LIKE! :)

[@Nudnik1]

Typical wait until transmission slips burns then change oil and filters.. Goofballs Clutch friction fragments means forward clutch pack roasted . See it so many times.

[@sabascarpio1151]

La mía no aplica que puede ser

[@jdguy8499]

👍

[@ivanloko8292]

you skipped the most importan the fill part

[@Woodywater]

You sound really unsure of yourself, so that’s probably why they didn’t let you do the transmission. Gotta know what you’re talking about then your customers have faith in you.

[@paulsequipmentrepair823]

Unsure of myself? I am not sure what you're talking about. I went straight to the problem and diagnosed it, and informed the customer. If I didn't know what I was talking about, I wouldn't still be in business and in high demand. You're pretty sure of yourself sitting behind a keyboard and trolling, but I am sure you're not good at anything else.