Case puma 240cvx, a look at the controls (part 2)

[@nufcpanter7599]

I am driving a case puma 185, and its the best tractor ive ever driven. I think its better than a fendt

[@antonybull998]

Nice Jonny, The “M” button is manual mode. Basically stops the engine and gearbox communicating with each other. Which in turn makes it a conventional tractor. After pressing the button, you need to move the MC controller fully forwards. Then the clutch can be used as you would in a power shift Puma. Your hand throttle and foot throttle then control the engine revolutions and travel speed in accordance to the selected speed on the corner post. Loving the vids mate, Ant @ Farm* LTD

[@antonybull998]

Grandad switch lol. I think it also stops any range changing with in the gearbox. (Might be wrong there) Been wanting to do stuff like this myself when demonstrating but I haven’t got the balls to do it. Keep it going mate! CASE IH FTW! ;P

[@Jonny1388]

You should do it dude!! You always get nice shinny new kit to play with! If you could get me a chrome exhaust shield for the 240 I’d even consider giving you a shout out! Lol Surly my videos must be good advertising for case IH?? Lol 🤣🤣😜😜

[@Jeffnz020]

​@@Jonny1388Na for steep hill country. Give operator full control. Leave it to the computer and you be stuck as they put too much power to the ground. No computer can drive as good as a human when the conditions demand 100%

[@rich7584]

Can you do a vid explaining how to use the exhaust brake and how to correctly drive a cvx

[@FarmerDavid]

Aggression lights - First = Road work, Second = Field/Road work, Third = Purely field work. From CNH Field Test Engineers themselves. We do quite a bit for CNH.

[@Jonny1388]

Yes that’s right! I much prefer the new software that controls the aggression switch on the tier4 cvx’s. The old software felt a little bit like a “launch control switch” lol it went from old lady crossing the road.... to leisurely jog....to scalded cat lol

[@nagd2010]

Great video, love the explanation of the controls. I realy like tractors and such, but unfortunatly I never realy use them (yeah, a real old 1967 Ford, which ofcourse hasn't got any of those fancy controls :P), but when I see the inside of the cab of a modern tractor I always wonder where all the buttons and switches are for. That's what I realy like about this video, that you explain in general what they do.

[@andyrichards4282]

Mint video’s, I drive puma 165cvx and love it!

[@Jonny1388]

I had a Puma 165cvx....great tractor!!

[@roaddawg3217]

​@Jonny1388 I have one on my computer farm Sim! It's my absolute favorite tractor ❤

[@IwanTimmermans]

Totally love your channel! Keep it up

[@alexandros3222]

Great explanation Jonny! I have a maxxum 150 CVX and I wonder if you know how to lift up the rear linkage slowly. I know how to lower it slowly, but i have no idea how to raise it. There is an option to do it by pressing the lift button of the multicontroller 3 times, but there must be a more straightforward way...

[@channeljp1607]

Great video Jonny, I could now jump in and drive one!!

[@richardl7759]

Can you explain the controls on the Fendt too? And how to set up your go/end buttons, etc?

[@killerioths]

Hey great video!can you tell me if u can change direction with out use the raverse behind the steering wheel?

[@V6weeks]

Has anyone found the arm rest in these tractors wobbles about real bad? Is this normal or should they be fairly solid? Thanks

[@bobpaterson1845]

Really interestin stuff Jonny can understand now why it's all youngster's drivin tractors nowadays 😅

[@craigmacdonald7645]

Great video keep up the good work! I have a 225 puma love it! Just wondering where did you get the case carpet in your tractor?

[@framfull]

Great clip Jonny! I have a 240 2016 I think. When I want to lower the rear linkage I have to give it a quick uplift and then down, this on the lever. If I dont do it linkage go down really slow. May you have an idea why its like this? The salesman on Case have no idea what Im talking about.

[@Jonny1388]

Hello my mate! Do you have to do that everytime? Mine will lower very slowly the first time i drop the linkage, first thing in a morning or whenever I key off the tractor. It's to do with the linkage height sensors learning the position. Bit after that it's fine and will drop at whatever speed I set it too. There are a couple of combinations you can use on the multicontroler linkage buttons to make it lift up slowly or lower slowly. Sounds a really silly question but what have you got your drop rate set at, under the armrest?

[@nathanjohnson7779]

What boots do you have I have V12 rawhide

[@jcgeerling9719]

With M you use your stick for speed and your pedal for revs never use it either but im sure there is a use for it...

[@pjagrivideomcmanus3661]

I never drive a case puma but are they automatic

[@eemil222]

How to put every block float when u put a hose in (joystick)

[@danhickling3565]

Good video jonny!, Deano sent me

[@Jonny1388]

Thanks dan! I hope you like the rest of them too! Thanks for coming over dan. It’s really appreciated! Take care mate Jonny :) 👍

[@zjurinec1]

Where is field and road mode (like mode I and II in Fendt)?

[@Belasca]

0-50km/h without shifting gears

[@tedbradford6238]

Great vid Jonny we got two pumas,quick question does yours hold its revs and ground speed when spreading fert on the downhill,ours won't 😕

[@Jonny1388]

We don’t spread fert tom, we’re not allowed to with it being an organic farm. I know what you mean though, I have the same thing with other implements we use

[@tiddles7043]

Do ya work for strawsons if ya dont mind me asking

[@Jonny1388]

I don’t no. I’ve got a friend that works for strawsons though. He’s called Jonathan, so very similar name!

[@tiddles7043]

Jonny 1388 im starting work there at Christmas when turn 18, i courrently work on our family farm but id like alot more hours. Ive got a few videos if you'd like to check out. Keep up the really good videos!

[@martinbohinc3310]

How old is this tractor ?

[@Jonny1388]

18months old :)

[@martinbohinc3310]

Nice 😁

[@poponetdanut9018]

Come funziona presa di forza

[@حسينسعيد-ع8د]

طريقة تحويل الولاده من كهرباء 12ال24

[@domclews8704]

where is your key!!?? haha

[@Jonny1388]

Haha!! Well spotted!!! My key is pretty worn out so I can take it out the ignition after i start it. I’ve got 100’s of keys on it, it jingle jangles all day if I leave it in. Gets annoying after 5 mins of bouncing down a rough track lol

[@domclews8704]

haha fair enough! Do all cases have the same key? We have a case maxxum and they key all look the same? and they coded?

[@poponetdanut9018]

Salve