Cat 320DL EXCAVATOR LOW POWER & OVERLOAD, HOW TO FIX.

[@jamieyeomans3803]

Really hard to find any info on diagnosing excavator problems sure glad you did this one. Thank you.

[@caterpillarjhunhunk]

usually the monitor of cat excavator is limited

[@gachanjamaina5668]

Hae sir .you helped me to fix the problem. Thank you very much for your video.

[@caterpillarjhunhunk]

ok no problem,contac me in my whatsapp [phone]

[@mohammedzakir1480]

Thank you master.. for help us by this informative video thank you so much

[@caterpillarjhunhunk]

welcome bro,thanks for the support

[@aguinaldojose6925]

Nice shot MASTER. This adjustment must done in both pump, i mean right and left side, the same size of turn, counterclockwise, until the engine not dying when u move the joystick. First make SURE power shift and main relief valve pressure are in spec. Important also to know about whats first and second stage.

[@caterpillarjhunhunk]

yes boss if we needed,or sometimes its happens just only 1pump,but to make it sure the adjustmen will be perfect you must have the chart for the adjustment you should have to do it for both pump one time complete pump setting of pressure

[@happyanimals8505]

You should make video bro Aguinaldo jose to share your knowledge too.. cheers mate.

[@samsonmaina8689]

To be honest your very helpful, thankyou

[@caterpillarjhunhunk]

thanks bro

[@majedzyoud9581]

Thank you for your good explanation , i have an issue of my 336D LN ‏excavator,please can I contact you for some information? The pressure of the pump is 350 bar but when you try to do a move of bucket it’s not working and you feel like the oil isn’t coming back, however pilot pressure is 40 bar.

[@TahaElhofy-b9x]

where are you from

[@caterpillarjhunhunk]

Bro can you contac me in my whatsapp [phone] for faster coversation

[@majedzyoud9581]

@@TahaElhofy-b9x I’m from jordan

[@majedzyoud9581]

I want to know which valve is responsible for the pressure of the return oil, It’s could be the anti drift valve or the regenerated valve ?

[@ibrahemawd]

my friend I have one question why the out put flow of the pump changed , when the same hydraulic pump is working good before

[@caterpillarjhunhunk]

sometimes thats happens while the pump is working some. mechanical reaction was change some clearance will become change at long run, we never know exactly how thats happen so the only to do is just check the pressure and do the possible adjustment if we needed

[@edwinmorre3973]

sir jun we have also here in davao city philippines a Cat 320d, engine RPM will not increase or go high when we operate the unit,your advice to this kind of problem is highly appreciated,thankyou and more power to you po!!

[@caterpillarjhunhunk]

what do you mean not increasing acceleration even without load,or accelerating without load,but when you operating or its load to work acceleration is goes down, meaning its eighter engine low power or hydraulic system is the reason,just because unregulated pressure of hydraulic,can you kindly check or give me some information about your engine it is smoking to much or what i dont know.much better ad me in your whatsapp [phone] and send me more infortant pictures or video about the status of your engine or the whole machine.

[@901shahzad]

@@caterpillarjhunhunk hi

[@EduardYupanqui]

Mi pluma perdio fuerza al escarbar alguna solucion ayuda gracias

[@caterpillarjhunhunk]

Muchos gracias amigo

[@nanheyadavyadav1318]

Can you provide caterpillar 352 about hydraulic system

[@jamieyeomans3803]

I have been having this problem with my 1995 ex60-3, and thought it was a fuel issue I will get some help to establish if it is pump problem, thank you.

[@caterpillarjhunhunk]

welcome br

[@sadikmohamed532]

تحياتي سيدي بارك لك الله في عملك واعانك سوءال هو اين اجد صمام تحكم في قوة زيت مطرق هيدرولكي على موزع هيدروليك وشكرا محمد من مملكة المغربية

[@doeeric8813]

Good morning Sir thank you for the video am from Ghana 🇬🇭 i have Jcb330lc the boom and the stick is slow what should i do please thank

[@caterpillarjhunhunk]

ok bro can you send me any videos o how the machine movement,and also pic of details of machine o my whatsapp [phone]

[@doeeric8813]

@@caterpillarjhunhunk Thank you i send to you

[@fresshh18]

good night smigo...I have a problem with a caterpillar 312A that does not indicate engine temperature, hydraulic oil temperature or fuel level on the panel monitor. It started with a fault that the power was not going to the monitor, the machine stopped accelerating due to the knob acceleration now only does it manually the governor was replaced but it does not allow me to calibrate it reaches ACP01 and stops I would appreciate if you could guide me in a solution thanks in advance

[@caterpillarjhunhunk]

well we will try to help you just contac me i my whatsapp,[phone] send me any details regarding about the problem and type of monitor,i just wanted to see how i can help you

[@rianal.morisi1094]

Teacher, what is the reason for the decrease in power in the hydraulic pump when carrying weights?

[@caterpillarjhunhunk]

Bro thats depend on the situition, you have to think engine first before hydraulic system, some times cause of low power just because of engine not power full, have many ways on how to test if the engine is a low power

[@rianal.morisi1094]

Engine runs fine

[@elmercasipe8278]

im a beginner mechanic sir i have a question regarding of my client problem his 1 unit wheel loader machine always broken a main pump shaft..

[@caterpillarjhunhunk]

tell me witch brand of wheel loader,and where they get the pump from original supplyer or from some other supplyer producing local parts or duplicate parts

[@claudioandresschmidt]

Hola te escribo de argentina tengo para reparar la misma maquina tiene un problema que todo el sistema hidraulico es lento el giro, la traslacion los movimientos todo lo que sea hidraulico esta lento... que podria ser

[@jorgeivanangaritalopez7201]

Compa primero revisa las presiones de las bombas para que no vallas a ir a la deriva

[@contrarianthinker]

I have a crank but no start can you help me and I also have the codes that was registered in the cat computer

[@caterpillarjhunhunk]

Contac me in whatsapp [phone]

[@MounSoem]

Cat320DL -E Check filter/Fluid info What does jumping sign mean?

[@caterpillarjhunhunk]

Contac me in my whatsapp[phone]

[@ПавелИгнатьев-ж5ч]

Please show point, where connected pressure gauge?

[@caterpillarjhunhunk]

Bro all port for testing is available for ypu to test, main pump,pilot pump, and regulator valve

[@Kairosabe]

hello sir. thank you for this video. i apreciate it. one question: 2:54 where u get this info? wich program ? thanks

[@caterpillarjhunhunk]

what do you mean 254? , if your are talking about where i get this info, from the blessing of knowlege

[@Kairosabe]

@@caterpillarjhunhunk hi. Sorry, my knowledge of English is limited ahah. I was referring to the diagrams in the minute 2:54. Where can I find this information. Thank you sir

[@jeffleana4752]

Boss apektado po ba ung bakho sa switch sa likod ng armrest, ung switch po na man saka auto Ang tatak... ganyan din po kc bakho namin

[@caterpillarjhunhunk]

yes ang normal positiong switch eh lahat nka down position,yun lang kung may nagbaklas n nyan dati at naiba na ang position ng switch at wiring

[@rianal.morisi1094]

Hello teacher, I want you to tell me where the pressure sensor is located to warn of overloading of the machine Cid 1178.

[@caterpillarjhunhunk]

try to see under the boom cylinder if available there if not maybe someone make configured the sensor function, contac me in my whatsapp [phone]

[@ابوموسىابومحمد-ب5ط]

شكرلك اشتلد اين المشكله في هذه الحفار

[@salemsalem-bi6kp]

لدي مشكله في كتر بلر.320dL ينطفي المحرك من حاله ماهي المشكله انا اخوك سالم من اليمن

[@unobono]

thank you TTITO

[@ahmedovo3011]

again great video

[@arvinlagria1680]

Boss pwede mag tanong 312d low power engine bago lahat pati common rail funinjector bago pero nag low power

[@caterpillarjhunhunk]

e try mo rin e check ang booster intake pressure sensor nsa intake manifauld nka install un,try mo e dis connect saka mo paganahin ang machine ha

[@caterpillarjhunhunk]

at check mo rin pala ung return vavle ng common rail baka sobrang lakas n ng balik ng fuel nya dapat mahina lang un

[@KelvinNjolomole-ie8go]

Nice work

[@doityourself6879]

Hello sir..Ask ko lng po.. about 320d.. ano po pwedeng maging dahilan pag di po bumama ang negative pressure kahit nakasagad na ang mga boom

[@caterpillarjhunhunk]

Contac me in my whatsapp,[phone]

[@bonnielumapaz4202]

Good day Master.. Tanung ko Lang po kung same Lang din po yan Ng pag udjust sa 320?ganyan din po kc problem Ng backhoe namin.. Humihina ang makina sa boom up khet walang laman ang bucket..

[@caterpillarjhunhunk]

pressure check muna kyo,then check nyo rin ang power shift solenoid nka attach sa main pump yan s kaliwang side sa bandang ibabaw bka nagloloko n ung power supply o ung valve,ang power supply nyan galing ecm tpos dumaan sa switch s loob ng cab. sa likod arm rest sa right side dalawa switch doon,ung switch nya ay kpag pataas ang direction mobilit lalabas s monitor testingin mo

[@bonnielumapaz4202]

@@caterpillarjhunhunk salamat po master.. Pero master sira na po mga linya neto ehh. Naka bypass na po electronics Ng backhoe.., ung switch po sa gilid ung sa may arm rest hindi na po gumagana.

[@caterpillarjhunhunk]

ay ganun naka direct na basta dapat may nlalabas n supply s power shift nya ok lang pra atlist hindi mo n kailangan maglagay ng supply sa power shift nya.

[@bonnielumapaz4202]

@@caterpillarjhunhunk pano po gagawin ko master para hindi na dumapa ang makina kapag nag boom up?

[@caterpillarjhunhunk]

check mo ung power supply ng power shift kung meron kpag meron,paganahin mo sya ng full rpm ng nkakalagay ung socket then observe mo kung anu kaibahan kpag ttestingin mo sya n nka disconnect nman ung s power shift kung same lang sya n may power sa wala power supply,baka may sira n ang power shift mo eighter stock o d n talaga nagffunction ung coil at valve nya.

[@adipmh7302]

Salut..am un schaeff skb 800 si nu mai vrea sa mearga bine doar supra turat...nu mai are putere la deplasare...merge incet si fara putere ...si nu as renunta la el...ce pot sa REGLEZ .te rog..

[@caterpillarjhunhunk]

sorry bro i dont understand what you say

[@laarnimangayan7169]

Sir Tanong ko lang po Ano po 247-9 320 GC

[@GerardoBriones-p1b]

Sir gud pm,ano kaya ang problema nitong 320 d pag nag boom up namamatay ang makina.salamat sir.

[@caterpillarjhunhunk]

Brad marami.kasi dahil kung bakit ganya, unang una baka kinakapos s diesel, o kya may active error sya n dahil ng ganya namamatay, or baka walang supply ung power shift mo n nsa mainpump

[@marcosconde2726]

Tengo una duda por ahí donde trabajo hay una cat 320 cl y anda fallando cada que empiezas a trabajar,pierde fuerza al subir el brazo y al recojer y supuestamente son las electroválvulas y ya las cambiaron pero sigue igual alguien puede ayudarme?

[@caterpillarjhunhunk]

this my whatsapp #[phone] contac me here ok i need more details of your machine

[@jorgeivanangaritalopez7201]

Compa lograste solucionar yo tengo el mismo problema

[@pablolizano8081]

​@@caterpillarjhunhunk have the same issue with a E120b . That will solve it?

[@happyanimals8505]

Thank you boss

[@caterpillarjhunhunk]

your welcome bro

[@rodjiecaparoso79]

boss pano mag adjust pag slow power cat 311D excavator...

[@caterpillarjhunhunk]

paanung slow nag check nba kyo ng pressure, add mo ako sa whatsapp [phone],tapos send mo sa akin picture o video ng slow movement ng machine saka serial number

[@jimboydexplorertv.6647]

...sir tanong ko po sana paano po ba ang gagawin kapag mabilis po gumalaw ang stick ng unit smooth po lahat maliban po sa stick.. komatsu pc200-8 po unit ko

[@caterpillarjhunhunk]

brad ung bilis b ng stick eh affected ang trabaho o wala nman or parang mamamatay ang makina ,whatsapp [phone] mo ako. sir para mabilis ang usapan natin

[@air0223]

Pagkatpos ba iadjust ang cervo kailangan ibalik sa dati? Or pag adjust un na yun po?

[@caterpillarjhunhunk]

normaly kpag nagadjust,dahil mababa ang pressure or kailang e adjust dahil wla n sya s normal,fix n yun until s magbreakdonw n ung inadjust

[@laarnimangayan7169]

Sir Ano po error 247-9 320gc c 4.4 engine thanks

[@caterpillarjhunhunk]

yes, ang 247-ay data link pwede ung communication line between monitor, ecm controller, at engine ecm, ay may problema, maganda paba ang harnes ng machine mo, then - 9 abnormal update, check mo muna harnes nya lalo n ung nka plipit n dalawang kadalasan orange b, brown, or green brown check mo baka may damage n wiring.

[@yojsangenterolizo6496]

Boss sa 325d nmin na cat.may lumalabas sa monitor na battery voltage irregular.ano po dahilan.at pano ayusin?

[@caterpillarjhunhunk]

hanapin mo ung wire n maliit n nka attach s alternator, ung wire n iyon ay magrrecieve ng supply galing sa D+ pabalik s monitor para mawala ung irregular

[@yojsangenterolizo6496]

@@caterpillarjhunhunk nakakabit nman po ang maliit na wire,,xka tenester ko may kuryente nman.pro ayaw parin mawala dun sa monitor.

[@yojsangenterolizo6496]

Boss Anong po sira pag nakalagay sa monitor pump 1 dsi?ok nman ung man wirings.

[@karnailsingh3941]

Hii sir How can setting cat 320d all function can't start ok

[@caterpillarjhunhunk]

this is my whatsapp [phone] for better conversation

[@jrdanan2625]

Bos pwede makahingi nito? Para mapag aralan ko itong machine nato.

[@caterpillarjhunhunk]

Eh add mo ako s whatsapp[phone]

[@kristinesoriano7607]

idol tanung ko lang anokaya Ang problema Ng backhoe namin na caterpillar pag nag travil ka nawawalan Yung boom up at nahina Ang travil nya,

[@caterpillarjhunhunk]

anung model no. nya cat mo,maf check muna kyo ng pressure kung gumagana p monitor kahit s monitor lang pra makita nyo kung normal b pressure o bumaba n sya

[@archelaredidon3234]

Help mi sir ang engine no promblim .pag gumalaw Morag pong.ngan .ang andar sir anong problima sir help mi

[@archelaredidon3234]

Sir. Ok .ang engine. Ang problima sir pag gumalaw tanan Morag pung ngan ang pwersa sir anong sira sir

[@caterpillarjhunhunk]

Brad contac me s whatsapp [phone] para s iba pang detalye

[@revolution19800828]

👍👍👍

[@Agirhydro23]

Having problem with powershift solonide not working cat 311uc.what should be voltage at this solonide .serial no of machine cat 0311ccckeo1276 or how to adjust thank you

[@bearbait2221]

sorry I looked at the manual i was wrong HIGH5. good work my bad

[@romeodavela8019]

How to adjust a picture

[@caterpillarjhunhunk]

Of course you have to touch the machine sir if you want to do something

[@riyazahmed7438]

Tell me low haydraulic power boom is too slow

[@caterpillarjhunhunk]

the exact procedure of hydraulic system you should have check the pressure first okay,if you understand the line of boom follow the line then,if you know the hydraulic valve that connected to the boom line you adjust that valve

[@AdrianPadilla-cp7ow]

If the engine suddenly stop and having blasted inside the engine and its stop the operation

[@caterpillarjhunhunk]

Bro you told blasted, of course no chance to operate you should have to inspect

[@loyfoxmacabodbod894]

anong problma sa excavator kobelco SR60 master the hydrulic low power pag mag work 2 to 3 hours..mahina ng gumalaw

[@caterpillarjhunhunk]

ok bago ka mag proceed s technical adjustment or repairing ng mga possibling naiisip n sira,ganito inspection muna,una check ang oil kung kilan huling napalitan,sunod oil filter kailan napalitan,at tingnan mo kung na deform n sya

[@becongcabahug7016]

boss saan natin ikabit ang pressure gauge?

[@caterpillarjhunhunk]

kung the same machine may mga port dyan s pump left and right power shift, at pilot

[@markkevinobejero8121]

sir okie langba hingi ako ng tulong sayo kasi yong volvo namin 460 low power ang kanyang bucket in

[@caterpillarjhunhunk]

check nyo maige baka hindi lang bucket ang problema,o kya kontakin nyo ako s whatsapp [phone]

[@markkevinobejero8121]

@@caterpillarjhunhunk sir salamat sa time mo saakin try ko sya kanina mahina ang kanyang bucket in ang bucket out naman malakas tapos pag ginalaw konalahat mahina sya conte

[@muzafarkhan4900]

Bro 330 have same problem load well taking engine

[@caterpillarjhunhunk]

bro check first power shift if power supply available

[@ACEautoworks]

Sir good day bago nyo pong folower sana po matulongan nyo ako bagong mekaniko ng heavy equipment.sana po mapansin nyo

[@bearbait2221]

Hay buddy I think you turned the wrong nut for that adjustment. The large nut holds the assembly to the housing. The smaller jam nut by the Allen screw is the adjustment. There is 2 ways to skin a cat :0 I could be wrong that's my 2 cents

[@caterpillarjhunhunk]

Big and small nut is a part of adjustment if start to adjust small nut it takes time to get the exact adjustment you need unlike the big nut it is faster respond

[@bearbait2221]

@@caterpillarjhunhunk I realized that thanks we learning thanks for the tips.

[@caterpillarjhunhunk]

@@bearbait2221 no problem bro if you are confuse to the what i was done try your idea, i just share my experience to anyone where you can possible normalize the heavy load cause of hydraulic failure, but you have to observe the engine power before you do the following way of adjustment

[@reidtubechannel]

Good day po sir baka po pwd makahinge ng manual nyan salamat.

[@caterpillarjhunhunk]

boss anung manual ba,tv or dvd,joke bigyan mo specific type of machine,maybe i have or not

[@reidtubechannel]

@@caterpillarjhunhunk thank sir for 320drr sa hydraulic system sir ty..

[@monthontractor2024]

ArkArk🤣🤣

[@markkevinobejero8121]

sir patulong naman kasi yong volvo210 namin ganon din

[@caterpillarjhunhunk]

hahaha ganun din,parang nag kwento kna s akin ah,bigyan mo nman ako idea s problema brad ha

[@tjrgarcia9978]

Good day sir nasa pinas po kayo. Ask ko po sa number nyo. Tawag po ako kc low power ung unit ko.

[@caterpillarjhunhunk]

Brad nsa uae ako dito nlang s whatsapp

[@mdasadulislam-sd8um]

দিস ইজ দা প্রবলেম হাইড্রোলিক

[@ugyendorji894]

Hi

[@caterpillarjhunhunk]

yes bro hi

[@ugyendorji894]

@@caterpillarjhunhunk i have caterpillar 320D excavator with hydraulic trouble shooting...so i will be great full if you can help me😊

[@ali9153]

ممكن رقم جوالك

[@crazyalien8476]

Pwede po ba makuha number nyo sir

[@caterpillarjhunhunk]

[phone]

[@luismera4308]

Traducir a español

[@WasimKhan-kt2mq]

Sir content.nambar

[@caterpillarjhunhunk]

[phone] whatsapp

[@ACEautoworks]

Sir good day bago nyo pong folower sana po matulongan nyo ako bagong mekaniko ng heavy equipment.sana po mapansin nyo

[@caterpillarjhunhunk]

ok anu b ang maitutulong ko

[@ACEautoworks]

@@caterpillarjhunhunk rega 320B dumadapa yong makina at namamatay pag pinagsabay yong galaw