Changing a Seacock on a boat in the water

  Рет қаралды 44,411

morgan griffin

morgan griffin

Күн бұрын

Пікірлер: 36
@geoffreybell6705
@geoffreybell6705 3 күн бұрын
Thanks for the video did my ball valve today the way you did work great thanks
@ozskipper
@ozskipper 5 жыл бұрын
Less stressful option. Go for a swim and put a plug in from the underside first.
@MarkGarry-r3k
@MarkGarry-r3k Жыл бұрын
Thank you so much bro. I just bought a 39 ton Formosa, needs 3 seacocks replaced, I thought water would fill 30 gallons in a few seconds. Now i have confidence to tackle it...hoping i get the right size and thread pitch.
@davandbre
@davandbre 5 жыл бұрын
Worked in the plumbing and heating and gas industry for years, this method is affectionately known in the trade as "snatching" and many a tale and story told of where it went wrong!
@watchmestress4182
@watchmestress4182 5 жыл бұрын
Cool video thanks for the upload. Don't forget, put the seacock in the closed position before taking the handle off.
@jasonfrodoman1316
@jasonfrodoman1316 10 ай бұрын
Or you can dive under the boat and plug the thru hull with a tappered cork. And you can seal the threads also.
@abrahamsintram7889
@abrahamsintram7889 5 жыл бұрын
Both seacocks and the thru hull look corroded way past their expiry date?
@donwill3442
@donwill3442 3 жыл бұрын
No tape?
@glaxowelcome1907
@glaxowelcome1907 5 жыл бұрын
That;s not actually a seacock that you installed. It's just a ball valve. What you removed was also a ball valve. A proper seacock has a flange on the bottom and is attached to the bottom of the boat. It is much stronger than a ball valve.
@white3722
@white3722 6 жыл бұрын
What about pipe dope or Teflon tape?
@freelectron2029
@freelectron2029 5 жыл бұрын
would have liked to see a bit closer shot
@parovelb
@parovelb 2 жыл бұрын
Led Zeppelin as background is a must 👍
@chrisfarley9707
@chrisfarley9707 2 жыл бұрын
Never tighten a valve where that union is you can over-tighten and crack it…Grab up top Instead… Should’ve put never seize lubricant on those threads while u had it plugged…. That valve will seize right to those threads and it’ll be a nightmare taking it off…
@sailing-etanche
@sailing-etanche 4 жыл бұрын
Thanks for the video and the nice music👍
@droneliveUK
@droneliveUK 6 жыл бұрын
nice no nonesense video , all the best , cheers.
@droneliveUK
@droneliveUK 6 жыл бұрын
in fact its how all youtube vids should be...... no "big up yourself" intros, repeatative obvious chatter, just what it says it is........ and it has a warm genuine feel to it. Thats what people want.
@droneliveUK
@droneliveUK 6 жыл бұрын
imagine if all the bullsht was taken off the internet and it was a rescourse for learning , a reliable scource of information...... to help the development of the human race, instead of the development of some rich peoples kids. HERES HOPING MORGAN !!!
@geoffallen1331
@geoffallen1331 6 жыл бұрын
would you advice the use of ptf tape or other sealer. id have more time as my boat is out of the water. geoff
@jmschreiner
@jmschreiner 5 жыл бұрын
5 min epoxy like jb weld
@ManicPandaMedia
@ManicPandaMedia 2 жыл бұрын
Good Job 👌🤙🤙👌🐼
@jvmalta081
@jvmalta081 2 жыл бұрын
good luck for when you break the trough hull fitting !
@eskokoskenranta6280
@eskokoskenranta6280 2 жыл бұрын
Must ask, what is a rounding wire, is that a steel boat ?
@kidbogle
@kidbogle 3 ай бұрын
Grounding wire
@boardelia
@boardelia 6 жыл бұрын
Hi, nice job there ! Aren't you changing the bottom part yet ? Looks corroded too I was wandering also if you could get a seacock from any hardware store or it has to be special marine equipment ? Last thing, i have the impression that not all seacocks are grounded in the boat, could you make a video on how/what/where to ground ? I might ask rookie questions but i'm totally new to sailing !
@Bakanelli
@Bakanelli Жыл бұрын
Thats a good question!
@FlyJFY
@FlyJFY 4 жыл бұрын
great video, thanks!
@primitiveleatherworks
@primitiveleatherworks 7 жыл бұрын
Hi Captain! Cool video
@yayita2024-n5c
@yayita2024-n5c 5 жыл бұрын
Thanks!
@estrelladelmar6466
@estrelladelmar6466 5 жыл бұрын
I'm needing to replace a seacock and that looks so scary to me.
@guyprimo6414
@guyprimo6414 3 жыл бұрын
Tell my brother Chris about the ground system
@eag725
@eag725 5 жыл бұрын
Well done
@SOLDOZER
@SOLDOZER 4 жыл бұрын
Use a Seabung. No panic and you dont have to get in the water.
@martynsutton330
@martynsutton330 6 жыл бұрын
Nice to hear led zeppelin in the back ground 🤙
@larryjohnson5597
@larryjohnson5597 2 жыл бұрын
The duds wrench looks Worster than the seacock
@sysublime5091
@sysublime5091 4 жыл бұрын
You would have been screwed if you had broken that thru hull off. In the process
Repairing a Thru-Hull with Boat in the Water
29:40
Josh Post
Рет қаралды 65 М.
Seabung™ seacock replacement whilst afloat
2:14
Seabung
Рет қаралды 67 М.
Мен атып көрмегенмін ! | Qalam | 5 серия
25:41
Let's talk about Seacocks Part 1
16:51
Russell's Randomness
Рет қаралды 54 М.
Clearing a clogged Sea Cock aboard Chicory a 46 Nordhavn
11:02
BoatersDivingGuide
Рет қаралды 1,7 М.
Can You Float a Liquid on a Gas?
19:17
Cody'sLab
Рет қаралды 3,2 МЛН
through hulls, seacocks, backing blocks Groco
12:46
Sailing Vagabond Epicurean
Рет қаралды 65 М.
Goodbye Bronze! Upgrading Our Thru Hulls
23:34
Out Chasing Stars
Рет қаралды 37 М.
Carvel Planking Ep16: Seacocks
12:34
Smithy's Boatshed
Рет қаралды 10 М.
Spartan Marine Seacock Replacement
26:01
Shane Rossiter
Рет қаралды 2,3 М.
Мен атып көрмегенмін ! | Qalam | 5 серия
25:41