CHEAP & EASY! Brushless Upgrade for RC Crawler Car WPL / MN - 2 speed gearbox

[@gadogamix]

Note: 1. You might use lighter to heat the pinion to make it easier to remove 2. For offroad usage, choose low KV brushless and small pinion gear. Dumbo RC X6: t.productlink.io/l68ao ESC (not same but similar price): t.productlink.io/l68ap 2445 3600KV Brushless motor: t.productlink.io/l68aq Battery: t.productlink.io/l68ar

[@zaksblog9570]

Can I use a 25a esc?

[@joshrandal4001]

That jeep is off the hook, fast. Awesome job.

[@scaleworksRC]

I just put one of these in a Mini T 2.0 because the Spektrum motor is like $90! I got one that was lower than the 6000kv that comes with it because it's just too much power for that chassis. I used the 2435 motor with 4800kv and it's much more controllable.

[@BetterWithWheels]

Men, incredible video, just because of you I decided to brushless conversion! I have portal axels so my top speed will be the half (2/1 reduction) I’m thinking to put 2445 5400kv with the 8t original pinion… you think will be stronger enought to crawl in first gear? Will be coging? Want to be fast in second, now I’m always in the fast gear! Thank you men

[@933pilgrim]

Dream to make WPL trucks like Dakar rally trucks and cars with brushless set up. Do you think its possible to make it with 30-40km/h speed?

[@christopherantonio3453]

Iwant to upgrade my MN 99s to brushless motor 2430-8200KV or 2435-6100KV??????

[@theminiatureconstructionco4556]

OMG that things rapid! Thanks for sharing! 😄👍

[@gadogamix]

You're welcome friend 😊

[@cheapmunkph]

when you use that for long time it will not melt the gearbox??

[@panhouska]

Hi. Should I go for C24 or C24-1? The latter is surerly better out of the box, fully proportional, but in some distant future I will upgrade it with stronger motor etc., so which one should I get? Or rather I should go straight to higher stock setup performance car like Ascent18, Venture18, or SCX24 Base Camp? (since I am completely new to the hobby and I have no idea how to upgraded except of changing tyres, that is something I am quite comnfident I am capable of)

[@softyan]

Yo quiero instalar un 2430 de 4500kv con un piñon 13T pero veo que no va seria mejor con un 6T o cual recomiendas.

[@dumepaoli2a]

did the drive shafts or axles break because of the 390 engine horsepower? 

[@andreicarloanda9125]

What motor , rx tx and esc upgrade can be applicable for mn82 for it to be fast?

[@jamesdoornewerd5850]

I have a 35amp 4200 kv setup,you need to push it, to make it go???I have the esc,card tuned-too???

[@axiziechannel6118]

Now i want to upgrade my 1/14 rock crawler

[@lipinghe40]

Wow! Very informative video, thank you and GOD bless.

[@gadogamix]

God Bless you too :)

[@firdauscendol5005]

It is good for crawling?

[@mrkemblegilstrap]

hi! Great video, Bro!! I wrote down a bunch of info from this video. I intend to follow it closely. The only thing that I am not sure of is which gears are the pinion gears? It seemed like all 3 were? Thank you.

[@gadogamix]

Pinion gear is the gear that attach to motor.

[@mrkemblegilstrap]

@@gadogamix hi! Thank you for responding! I really appreciate that. I have a couple of questions, if I may? 1 The sheet you so kindly show with the list of motors, had the last few digits of their part numbers cut off. Are those numbers necessary when trying to buy these motors? 2 Do you have a favorite distributor of these parts listed in the video? The links you provided have possibly expired? I am looking for a goodly amount of power because my truck has a real metal body. It's about like the real 1955 Chevy metals thickness. And I'm going with an all metal 4 wheel drive frame and suspension. The all metal version of the WPL C24 suspension. I am definitely going for at least the 11.1 volt battery. The 6800 mv 2430 Y 4.5 motor. So, I definitely need a good ESC capable of this voltage and higher. Bro, I built a 19.2 volt pack that I'm dying to use in something. More power muahahaha!!! Thank you, kemble

[@namyraoctavia3055]

Bang kalo pake gb single speed motor 2445 esc 60A bisa kencang kaya video di akhir ngga? Mohon masukan nya,🙏🏽

[@jaxxon3998]

Did you also change esc? How many amperes esc did you use

[@oscarr1548]

Ayúdame a modificar mi Mn-d90k, solo tengo el motor, no sé qué me falta

[@Morax_with-no-mora]

I own a mn d99s(with non-stock unknown brushed motor) and is ok at crawling but lacking in speed. I want to upgrade to a brushless. Will I still be able to crawl and increase top speed if I put a 2430/2435 with the stock gearbox?

[@christadams2249]

Tumpang tanya tuan..motor 2435 pakai esc 60A boleh.?

[@daijoubu4529]

Tamiya 8t is 0.5module, so true 5mm, is that why it's noisy? That 12t 6.9mm appears to be a 52 pitch gear, much more quieter, so 8t in 52p would be 4.88mm! So that means that WPL gearbox needs 52 pitch gears (imperial), not 0.5m (metric)

[@Wad3c]

Where did u buy the 8 tooth pinion gear?

[@kanekanechannel594]

This motor can be used in Single metal gearbox ?

[@BlvlWmpower]

Love it.

[@gadogamix]

Thanks :)

[@KAarnagemAmolgada]

good video...that´s afine mod for a trail rigg... lots of power !

[@gadogamix]

Thank you :)

[@BlvlWmpower]

Totally perfect speed imo too.

[@timbudge6136]

I bought a 370 brushless 6500kv installed onto 1 speed transmission but the motor shaft spins inside the pinion gear. Any solutions?

[@gadogamix]

Maybe the pinion is crack or loose, sometimes it's not visible to the eye. you need new pinion

[@sugarshanesmith]

Is it possible to upgrade the motor using the stock transmitter? it realy necessary to upgrade the esc and transmitter what are the pros and cons? just want a faster c24. thanks

[@gadogamix]

It's possible if you use the brushed motor. For example the motor with stronger magnet. But you can't upgrade to brushless motor if you still using stock electronic.

[@randalldrop8972]

@@gadogamix what if you have the upgraded electronic kit I have the c44 km with the 370 dual speed I have the es3 which allows the wax included in the kit to run lipos not sure how high tho

[@anangbuluck06]

Om... Repiu dong.. mn86 pake brushless

[@gadogamix]

he he belum punya MN86. Mungkin nanti kalau sudah punya

[@faran-]

Great information, and greately explained :D

[@filsdedieu100]

It's a good job ! thanks :-)

[@fyresg]

Very nice video, thank you! I have a *stock 180 brushed motor* (not sure what pinion), and the upgraded single gearbox *370 motor* (also not sure what pinion). I'm planning to get a 2435 motor so I don't have to cut the frame. I want to use existing pinion: either the pinion on the 180 or 370 brushed motor. Do you know the no. of teeth on the pinion, and the shaft diameter? You get good results with a 3600kv motor with 12T pinion. The cheap Surpass Hobby 2435 brushless motor comes in 3300kv, 4500kv, 4800kv, and 6100kv. Should I get 3300kv or 4500kv?

[@gadogamix]

I suggest you use pinion from 370 motor as it most likely have shaft diameter with 2435 brushless motor. You can use lighter to heat up the pinion for easier removal. If you still plan on doing offroad, then lower KV is a better choice.

[@fyresg]

@@gadogamix thanks!

[@angelopotenciano45]

hello. can you teach me how to put the lipo battery?

[@gadogamix]

1. buy the lipo battery that has same plug as the ESC. For example ESC in this video use T Plug. Then I need to buy Lipo Battery that also use T Plug. 2. Just plug the battery to ESC. Note: we can change the plug type, but it needs soldering the connection. You can watch this video to upgrade from RTR Version to Proportional system, maybe you can learn something: kzbin.info/www/bejne/iGevgZR9gtx8e7M (but those video is still brushed system).

[@gautamsenthilkumar823]

Brushless motor fits jjrc q65 ? Which one fits 2430 or 2435?

[@gadogamix]

If you use dual speed gearbox from wpl as in video, I think it will fit. 2435 should be fine.

[@gautamsenthilkumar823]

@@gadogamix do u build it for me I don't know to build stuff

[@rcflashcars]

cool job! big like! 👍👍👍

[@pmp0giboy]

What is the wheelbase and track measurement?

[@gadogamix]

Lenght around 20cm, width around 13cm

[@gnarlytek1331]

Rad video what mod pitch is the pinion gear can u send me a link?

[@gadogamix]

I can give you the link but the problem is I buy it locally in Indonesia and they don't send it overseas. For 12T gear, you can try to buy the gear for 380 size motor. Anyhow, here's the link: tokopedia.link/Pa0NF1nRm3

[@safiq.channel]

There is an Indonesian version, there is an English version Mantap lah😂👍

[@TheCaptmjr]

Great video

[@dredgewalker]

You're gonna wreck your axle gears with this as without any sort of differential. I have a c34km and if I wanted increase the speed I'd add differentials first then add a receiver with gyro to prevent the car from toppling as the c34 is top heavy and any fast turn would imbalance it. I would also widen the wheels for added stability.

[@gadogamix]

Yup, you're right. Beside differential, it will be better if I can add some clutch

[@mlkthegreat]

what is a brushless motor i can use for 1/18th scale rc?

[@gadogamix]

If the motor can fit in 1/18th, then you can use it. Try to measure the compartment. The motor in this video has a diameter of 24mm.

[@johneppstv]

40 bucks from Ali for motor and 2.3mm 12t. But after seeing the charger cost for lipo. Nty. Would put me 100 more in on a 30 c24 that I'm already 60 in on part with nothing in the mail yet. Kinda sad cuz I cant blow more money.

[@ightaditya]

Pakai pinion nya berapa T ?

[@gadogamix]

Lah kan di video dibahas.

[@mi3192]

Oh my god！how speed is light

[@BlvlWmpower]

It sounds like a two stroke dirt bike in first gear lol.

[@gadogamix]

😁

[@arixxblack]

Mantap bro. Channel versi British..loo

[@gadogamix]

he he ada versi indonesianya juga kok.

[@miyamotosan972]

Nice!

[@gadogamix]

Thank you! Cheers!

[@hajimeonthego5046]

nice..like watching documentary

[@gadogamix]

Thank you :)

[@simonwalters6733]

That's bloody awesome but too much frickin power, unless ....... u slam it? not seen that done yet. Mmmmmm

[@gadogamix]

Yeah, I think about to lowered it and change the tyre but don't have time to do that (yet).

[@rcgarageph7228]

Rc Popeye is now down these is the most fastest

[@gadogamix]

Yeah, I never try to measure the speed too. I claim the "fastest" because there is none of MN45 on YT that goes brushless at the time I upload the vid.... Or maybe I just miss it 😁

[@rcgarageph7228]

That's gonna be make it on steep hill but cogging issues

[@gadogamix]

Yup you're right friend. But at start only, after it run, there's no cogging / trembling issue. Anyway, I try to use quicrun hobbywing 16BL30 esc and the cogging effect is minimal. It's waterproof too and not that expensive. The drawback of 16BL30 is the cable so short.

[@maeldomain]

Great tutorial! Obviously you put a lot of effort explaining this stuff, May I ask if I can have your contact email or facebook? I do have a lot of questions and I'm kinda stuck where to start. lol

[@gadogamix]

facebook.com/gadoga.do.9404/

[@GilbertFrancoC]

put some weight

[@richardphillips107]

GARBAGE. No way to attach the pinion.

[@gadogamix]

People say "seeing is believing". But I guess that's not the case for you 😁