Chevy S-10 350 Install With Long Tube Headers!!

[@laurensiemens1436]

With long tube headers you have to make sure your wheels are pointing straight when idling

[@jaysgarage3616]

hmmmm , no. I don't get the reference. I do know on sharp right turns I have a header tube touching the crossmember slightly and causes a vibration. My mounts have settled and headers are close to touching in a couple places. Hope this helps!

[@BubbaAyers1969]

Great video, that’s a tight fit.. looking good 👍

[@jaysgarage3616]

Thanks for the comment!

[@Dookieandsons]

I also notice you are using -6 transmission cooler lines I had issues with the top one on mine pointing straight at the trans tunnel I had to finesse my trans tunnel a little bit to keep it from touching LOL just on the top-6 tranny line was the only one I've had issues with and with the transmission dipstick it went like butter it was easy as can be I used an aftermarket steel braided trans dipstick

[@turnandburnroadtripssouthe8432]

Excellent as usual!

[@jaysgarage3616]

I appreciate the comment , thanks!

[@yurimodin7333]

gonna be doing a 350 swap on my 2wd Jimmy......thinking about the Hooker manifolds, I hope they fit.

[@michaelvoigt724]

Hey, really good video 👍

[@jaysgarage3616]

Thank you , Thanks for the comment!

[@heshtesh]

No getting off easy when installing long tube headers on a 1st gen sbc in a s-10, i'll be facing the grim reaper soon when I install my 2" primary tube fenderwell headers on my 1st. gen in my 94 Sonoma, luckily guys have gone before me so their is You Tube help available along the way to get the exhaust wrapped around the frame.

[@jaysgarage3616]

Good luck on your install , hope it all goes well!!

[@leeroywarner1308]

If you take your time and look at it you don't have to cut the bell housing I have a 1992 I put a torbo 350

[@TBD0621]

Did you use a after market floor shift or use the shifter on the column?

[@jaysgarage3616]

I had to use a floor shift , was not able to use the column shifter.

[@BigUnk85]

Do the same rules apply for a second gen s10? And are shorty headers easier to deal with?

[@jaysgarage3616]

They are very similar , the 2nd gen seemed a little better than this truck but very minor.

[@dylanhoward5959]

Any have part numbers for shorty heady that will fit in an as10 with a 350 don’t necessarily wanna do long tube headers

[@jaysgarage3616]

A standard shorty header like a Hedman 69550

[@Luvv223]

What transmission did you bolt up to that 350 ?

[@jaysgarage3616]

Turbo 350

[@Chrissutter35]

What starter did you use

[@jaysgarage3616]

universal proform?

[@jaysgarage3616]

I think they are called performance world up here.

[@Dookieandsons]

It's really not that difficult all you do is bolt 2.8 frame mounts directly to your frame in those three holes they won't write in you have to grind a little ears off of the 2.8 mounts at the bottom then you bought your trans dapped mounts to your engine and it will sit right in place I used my same crossmember that came in my truck with a 4.3 V6 I used my same transmission that went behind the V6 and I also used my same drive shaft that came in the truck originally and I have had no issues I have been daily driving my truck for a year-and-a-half with no issues you can actually see it on my channel I drive it everyday

[@jaysgarage3616]

Your truck looks good , I have actually seen it before. I would have bolted the 2.8 mounts to the frame if I was running the short headers like yours and I could have used the factory driveshaft as well without needing to cut it down but these headers would need alot more denting. The set up I have moves the engine up slightly and back. Thanks for the comments and I will watch your build progress , its always fun looking at other builds!!

[@Dookieandsons]

@@jaysgarage3616 yeah mine's been finished and driving it's a street truck I drive it everyday it has been finished about a year-and-a-half but there was still be more footage of it I'm always changing stuff out but it has been dependable for a year-and-a-half other than I had to change the transmission

[@richardkishbaugh3784]

Whats the part number for that mini starter you used

[@jaysgarage3616]

I'm not sure , I think its the same as all the other models that Jegs part # 10011, Summit Sum 829105 etc.

[@richardkishbaugh3784]

Ok thanks just trying to find ones that won't interfere with the headers I have the same ones you do an was looking for that starter cuz I see yours fit in there nicely

[@jamesquinnie7573]

Where did u get the headers from sir???

[@jaysgarage3616]

I bought them used from Facebook , they are available on Summit , Jeg's etc. The mounts for these headers came from Summit , as a package it worked out quite well. I actually drive the truck daily , until we get our first dump of snow.🙂

[@wreckanchor]

@@jaysgarage3616 do you know the part number for the headers please?

[@jaysgarage3616]

@@wreckanchor Hedman 69490

[@luispina4012]

👍👍