Oh wow, this is what I get for not doing a full replay efter final editing :( I am afraid there is not even a correction to do, the original files are gone by now. Sorry about that.
@Basement-Science4 жыл бұрын
@@KaizerPowerElectronicsDk No worries, happens to everyone.
@therasm244c4 жыл бұрын
Interesting setup for testing you got there! I've found that if you don't care too to much about sound quality, these small amplifier boards from China really gives a lot of amplifier power for very little money and with high efficiency. In the past I've run a cheap pair of 15" PA speakers with a similar board powered by two old deep cycle lead-acid batteries at Roskilde festival. With the music going at very high volume for almost round the clock the batteries could still last a whole week
@KaizerPowerElectronicsDk4 жыл бұрын
That brings me back, in an instant to Roskilde in 2005 I think? We had a T-amp in our camp and it was a revolution compared to the old car stereos or ghettoblasters that was common. I think we have the exact same setup with discman as seen here: 6moons.com/audioreviews/sonicimpact/t.html
@louieli29004 жыл бұрын
That is because of cheap inductors on this board, which is the major distortion source of Class-D Amplifier.
@dozyproductionss2 жыл бұрын
suggestions in how to replace for higher quality inductors?
@whatislovebutonelonggame54064 жыл бұрын
13:25 "Entering Bluetooth, waiting for connection" 14:00 "Play Music, entering Bluetooth, waiting for connection" the amplifier says
@Dj-Jon-E-C3 жыл бұрын
I have this amplifier module when grounded you get no hum noise at all
@demm77772 жыл бұрын
Mine has text still on the bt ic that reads JL AC20BP0A244-25F4, but it also lacks the 8 pin chip which was replaced by another cap instead
@briggsmedia4 жыл бұрын
Any guidance on how to connect an external bluetooth antenna in case you want to mount the board in a metal box?
@user-vv1qk6zu4p2 жыл бұрын
I already liked the video after watching for 5 mins.
@dozyproductionss2 жыл бұрын
If we have this board (or similar) is there a way to lower the distortion? I have a non bluetooth from a couple of years ago and I feel like it may be good enough for a boombox project but any way to improve it will always be a plus. Any other type of boards you can find on aliexpress that you'd recommend?
@jakk2ahao2 жыл бұрын
How many watt should i get if i use 24v 15a with 8 ohm speaker?
@MBmcoficial3 жыл бұрын
Hello man! Nice video! I have some kind of issue with this amplifier. I tested it on stereo and only the left side is going out on both speakers, and not stereo as it should be. Can you help me, or give me some start point to solve it? Thank by the way! 🙏🏻
@KaizerPowerElectronicsDk3 жыл бұрын
Return it to the seller and demand a refund. My own experience with different kinds of these cheap amplifiers is that they are manufactured way too cheap, there is too many errors or perhaps low quality reject components used in them.
@MBmcoficial3 жыл бұрын
@@KaizerPowerElectronicsDk THATS A CRAP! Thanks to the advice man, i'll return to seller and get my refound! one more time, thanks!
@robbieaussievic4 жыл бұрын
..... Well done Mate, informative, rational, cool for cats.
@anthonyares10253 жыл бұрын
my tf card is not can you give have a suggestions?
@mazmazen4 жыл бұрын
I have the same board, but have a problem playing through the minijack input. If I turn on the Amp with the minijack connected the Amp doesnt play. I have to unplug and plug the minijack in again before it starts playing. Somebody knows how to solve this problem?
@NOSTRA524 жыл бұрын
I had the same problem, and solved it, by trying it out. The solution is to interrupt the first two connections on the left and right of the print jack plug and put a switch between them. With a connection from right to left circuit board. That left leg is separate from the circuit board and the switch is connected to the circuit board. Sorry for my bad english, I am Dutch
@alvarog73343 жыл бұрын
when is playing music from TF card, can you change the song? I dont see any button. Maybe connecting new buttons to holes vol+/- that are near the TF reader?
@KaizerPowerElectronicsDk3 жыл бұрын
I got no idea.
@JohnUsp4 жыл бұрын
What signal generator are you using? Maybe the distortion comes from there.
@KaizerPowerElectronicsDk4 жыл бұрын
The signal is from the analyzer. With itself in loop it is 0.07% THD
@sunnysharma1375 Жыл бұрын
I am using the same amplifier board with 24v 10 amp SMPS for 2 * 40w (4 ohm) woffer and 1* piezo tweeter connected parralel on each chanell but the amplifier is tripping alot when I increase volume a bit or when the bass beats comes in music. I tried connecting speakers in series but the problem presists I am now very frustrated what can I do now to solve this problem.
@Sepkov Жыл бұрын
Did you check the thermal paste maybe it's overheating
@vuilledeeresh4116 Жыл бұрын
Use 8 oms load
@dhruvsingh9799 Жыл бұрын
this board features with thermal protection so better use 8ohms load and check if the IC TDA7498 is reaching around 140 degrees before the trip.
@audiokees40453 жыл бұрын
I have one but does not work, only a rattle is heared from amp.
@Momchil04 жыл бұрын
Is it possible that they used a cheap version of this ic from another manufacturer? That could also explain the measured THD. But I'm not into audio at all. I don't know if there are cloned audio amplifiers.
@KaizerPowerElectronicsDk4 жыл бұрын
I think it is more likely to be bad circuit layout or components around the chip than a cheap/reject version chip.
@NiHaoMike644 жыл бұрын
@@KaizerPowerElectronicsDk I suspect the use of ceramic capacitors in the signal path is to blame. Could upgrade them to film caps, but since the Bluetooth part most likely doesn't support any of the HD codecs, that would remain the bottleneck anyways...
@dozyproductionss2 жыл бұрын
@@NiHaoMike64 Any suggestions on where/how to replace the caps?
@jessetagore53854 жыл бұрын
is there a way to reset these boards. Most of the time doesn't detect on bluetooth as well as aux.
@KaizerPowerElectronicsDk4 жыл бұрын
I find that it is my phone that has trouble connecting to previously known units, but maybe it is a general flaw in BT units
@jessetagore53854 жыл бұрын
@@KaizerPowerElectronicsDk I tried connecting with other devices too. And even aux is a problem.
@logandark68754 жыл бұрын
If someone find a good board amplifier that we can buy ,please share it
@filipabdulaj40483 жыл бұрын
Is there a way to remove sound of chinese lady?
@KaizerPowerElectronicsDk3 жыл бұрын
I doubt that its possible :)
@filipabdulaj40483 жыл бұрын
@@KaizerPowerElectronicsDk I found this video kzbin.info/www/bejne/i3KuiWqDpdVlf5Y , if he can change name, maybe there is a way to change a sound?
@dst08154 жыл бұрын
Amplifier failure at page 14 :)
@jeffm27873 жыл бұрын
Terrible chip IMO. Used in FX1602S and LP1601S amps. For $10 it's fine, but not for $100+. I'm more of a TPA fanboy.