Tap to unmute

Circuit Board Prototyping Tips and Tricks

  Рет қаралды 206,827

0033mer

0033mer

Күн бұрын

Пікірлер: 166
@jerryocrow1
@jerryocrow1 5 жыл бұрын
First, thank you. Second, finaly somthing beyone "basic". I appreciate the effort, diversity, and accumulated knowledge.
@fathomisticfantasy2681
@fathomisticfantasy2681 Жыл бұрын
Really wish there were more YT videos like this in 2020's. I miss the old retro style of minimum grade recording. This video BTW is gold! I doubt there is a better introductory on soldering then this.
@prashantdawar
@prashantdawar 6 жыл бұрын
one of the very best video on the topic. Clear presentation. Impressive. Thanks for this contribution
@NabilTouchie
@NabilTouchie 6 жыл бұрын
4:08 that explains a lot of trouble I got doing a RF controlled servos project I'm doing... great tips!
@TheOleHermit
@TheOleHermit 4 жыл бұрын
Thanks for showing the various options, new and old. Did wire wrap during the late '70s. Recently became a 'maker', using solderless breadboards w/SBCs & MCUs. Just discovered Fritzing PCB design software, which has a great GUI that allows easy breadboard and circuit design migration to PCB layout. The files can be uploaded to online mfrs for inexpensive fabrication and quick turnaround time. Hope this is helpful for your viewers. 😎
@0033mer
@0033mer 4 жыл бұрын
Great tip!
@simonrussell4986
@simonrussell4986 4 жыл бұрын
Thank you for this! Was looking to make the jump from solderless breadboards, and a lot of sites seem to miss that out.
@0033mer
@0033mer 4 жыл бұрын
Glad I could help!
@Bednar121
@Bednar121 3 ай бұрын
There also is a variant of proto board with separate pads for each hole, IMO a bit more flexible than the strip boards, as well as double-sided variant (for each hole there's pads on both sides, connected together with a via, a tiny copper tube going through the hole), which is way sturdier and gives a lot more opportunities (what I like to do is to solder bigger SMD components on one side, and run uninsulated wire as traces on the other). And for those wondering, how to use smaller SMD components with a "pad" perfboard, there is also a 1.27mm (0.05"...? Sorry, European here...) variant, and lemme tell you, most of the typical SMD parts (TQFP, TSOP, et cetera) fit there really, really well. It's a bit tedious to solder them, because this is the realm of microsoldering, but IMO still worth the effort - you get a really flexible, sturdy, and high quality prototype (and even long-lasting, permanent) board in an universal package. They are a bit hard to find though, at least in Europe, sadly (when I *did* find them, I just bought a whole batch of 30 pieces lol)
@tonysicily2687
@tonysicily2687 3 жыл бұрын
Awesome, A great video, full of info, no crappy music and full of useful info. Liked, Saved, & Subscribed Question, if I may, where do you get the breadboards with the screw downs? The self adhesive ones peal off after a while
@0033mer
@0033mer 3 жыл бұрын
Thanks for the feedback. The company that made those breadboards ( Continental Specialties ) is no longer in business but if you check eBay you might find them there.
@BeyondDuctTapeFixItRight
@BeyondDuctTapeFixItRight 4 жыл бұрын
Your video is terrific! Your content density is superb. Your video compels me to give Veroboard a try. That's something I wouldn't have considered previously because I wasn't familiar with using a boring tool to make the isolation channels on the thing. I always wondered how and who would use these things. Thanks to you, now I know.
@0033mer
@0033mer 4 жыл бұрын
You're welcome ... glad it helped. Thanks for the visit and the feedback.
@GRANTwow
@GRANTwow Жыл бұрын
Perfect. This effectively illustrated how to use these different types of boards which will inform my first-time purchase. Thanks!
@0033mer
@0033mer Жыл бұрын
Glad it was helpful!
@MadLabZ
@MadLabZ 5 жыл бұрын
A very nostalgic feeling from your video, thanks for the upload very informative crisp and clean content!!!
@0033mer
@0033mer 5 жыл бұрын
Thanks for the feedback!
@StealthParrot
@StealthParrot 6 жыл бұрын
Great, I've never tried the Veroboard before, looks like a great way to go. Thanks.
@paulf1071
@paulf1071 5 жыл бұрын
Matrix board is another option.
@doctorcad1557
@doctorcad1557 26 күн бұрын
Nice summary! It was to the point and covered some good topics. Helpful. Thank you!
@0033mer
@0033mer 26 күн бұрын
You're very welcome! Glad it was helpful.
@graxjpg
@graxjpg 4 жыл бұрын
This is awesome, thanks so much. Tube amps still use terminal strips, which are fantastic fun to build.
@0033mer
@0033mer 4 жыл бұрын
You're welcome.
@eduardperdomo1038
@eduardperdomo1038 11 ай бұрын
Excelent video! Can you talk more about the wire wrapping tool or, I don't know, make a video about the use of that tool. Thanks.
@blankstares4355
@blankstares4355 5 жыл бұрын
Excellent. Thank you for showing all these various methods.
@0033mer
@0033mer 5 жыл бұрын
You're welcome!
@trucker18944
@trucker18944 4 жыл бұрын
Question. At 1:55 you talked about plastic box enclosures. The ones you showed in the video are green blue. Did they come like that or did you paint them that color?
@0033mer
@0033mer 4 жыл бұрын
They were bought that color at a local electronics supply store.
@trucker18944
@trucker18944 4 жыл бұрын
@@0033mer 👍
@mkall
@mkall 3 жыл бұрын
thanks for the video, you showed the info i was looking for beautifully. it seems that the veroboard is the best way to do this. I was hoping to avoid boring the board and getting the ones with isolated holes but i think that is more hustle trying to connect the components with their leads/solder
@0033mer
@0033mer 3 жыл бұрын
Glad it was helpful!
@0033mer
@0033mer 3 жыл бұрын
Veroboard also make good heating elements. kzbin.info/www/bejne/jYWcqYqvgbBgf8U
@pingoleonfernandez7638
@pingoleonfernandez7638 5 жыл бұрын
Very informative video. Thank you very much. You should go more indepth with the Manhatan and the Dead Bug in further videos
@AnanyaMuddukrishna
@AnanyaMuddukrishna 7 жыл бұрын
Beautiful prototyping examples! Thank you for making this video with many useful tips. How do you make the wires hug the surface of the veroboard? Hot glue?
@0033mer
@0033mer 7 жыл бұрын
I use 22 or 24 solid gauge wire and bend then down after soldering and they will hug the board.
@alphahr
@alphahr 7 жыл бұрын
loved your Cosmac Elf. I still have mine from 1976
@0033mer
@0033mer 7 жыл бұрын
The first microprocessor I wrote code on ... kind of miss those days.
@y_x2
@y_x2 2 жыл бұрын
For the wire-wrap technic you can add plastic label with pin number.
@carlosgarcialalicata
@carlosgarcialalicata 4 жыл бұрын
Great video! an unrelated question. what is the wire joining two adjacent contacts in the middle of the board that you can see at minute 6:22: under the resistors
@0033mer
@0033mer 4 жыл бұрын
I normally install wire loops on the board to hook up scope probes for testing but in this case the wire loop is the Vcc ( 5 volts ) power connection and the other wire loop connected to pin 8 of the IC on the right is the ground connection.
@carlosgarcialalicata
@carlosgarcialalicata 4 жыл бұрын
@@0033mer Thanks for the answer. That is actually very useful :)
@Zanzubaa
@Zanzubaa 7 жыл бұрын
Informative video. Thank you for taking the time.
@0033mer
@0033mer 7 жыл бұрын
Thanks for the feedback.
@mrdzejk
@mrdzejk 6 жыл бұрын
And that was on 24th Dec - even more appreciated. 'Going to move my thesis project from a breadboard to a veroboard right now, thanks!
@chrisc9213
@chrisc9213 5 жыл бұрын
Good video, have a question, at @3.49 of the video you have breadboard that has a wider isolation channel, where can I pick one of these up at. I do a lot of work with larger Micro Controllers and this would be great to have.
@0033mer
@0033mer 5 жыл бұрын
The Experimenter 600 is no longer available, so your best bet is to check on Ebay. You can also remove the power bus strips from two boards and straddle microcontrollers between the two.
@chrisc9213
@chrisc9213 5 жыл бұрын
@@0033mer Thanks for the reply, it is not the same trying to piece together a board...lol. Not sure why they would stop production of a board that has unique value.
@0033mer
@0033mer 5 жыл бұрын
The large semiconductor companies are cutting back on DIP packages because of the cost as compared to surface mount (SMD) devices. NXP is the only company that makes an ARM microcontroller in a DIP package and that might soon disappear. One day we might not see microcontrollers in DIP packages which is sad for students who want to breadboard them.
@johnpautler4872
@johnpautler4872 4 жыл бұрын
Excellent video. Where would I find the boring tool that you use to create isolation channels with veroboard?
@0033mer
@0033mer 4 жыл бұрын
You can find them in various places online: www.rpelectronics.com/r22-0239g-veroboard-cutting-tool.html
@emremutlu44
@emremutlu44 6 жыл бұрын
5:04 That *Manhattan* technique looks like creating art on a copper plate. Do they sell those square "islands" on the board? It looks a bit hard to solder because of the thermal dissipation of the parts.
@0033mer
@0033mer 6 жыл бұрын
The Manhattan technique is basically a do it yourself project. You cut out your own islands from a bare copper clad PCB and glue them to the main board. This allows you to become very creative and your final product can look like art.
@sanfourbensanfer3911
@sanfourbensanfer3911 8 ай бұрын
This board for the PC looks very interesting. Was this an open-source project that you can share with us? Can you recommend any literature for a hello world project here? I always wanted to learn how to make a simple PCI card that just turns an led on/off and reads a button state but I couldn't find anything, especially devkits that don't cost several 100 of euros. For the Windows driver there are official tutorials in c# and c++.
@0033mer
@0033mer 8 ай бұрын
The PC card was used in a Fire/Ambulance dispatch system. The dispatcher could select each fire hall from the computer console and also bring up VHF radios throughout the city for communications. The board was the communication link to all locations using dedicated phone lines. The code was written in LMI Winforth.
@MorbidKayla
@MorbidKayla Жыл бұрын
Link for the pci and apple pc development boards ?
@robarmstrong4148
@robarmstrong4148 4 жыл бұрын
Great video. Where do you purchase cases like the blue one you show at 5:18?
@0033mer
@0033mer 4 жыл бұрын
They are made by Hammond. Any local electronics supply store should carry them. www.hammfg.com/electronics/small-case/plastic/1591t
@MrNonaste
@MrNonaste 6 жыл бұрын
Can you please give the exact name of that device you use for cutting channels in veroboard that you call a "boring tool" at 1:35. It makes beautiful channels but a search on Amazon doesn't find it. Thanks.
@0033mer
@0033mer 6 жыл бұрын
Here is a link: www.rpelectronics.com/r22-0239g-veroboard-cutting-tool.html
@MrNonaste
@MrNonaste 6 жыл бұрын
Thank you
@SpeccyMan
@SpeccyMan 6 жыл бұрын
It is called a "spot face cutter"
@Kimchi_Studios
@Kimchi_Studios 4 жыл бұрын
Wow! I learned a lot. Thanks for clearing up any confusion about prototyping and making connections.
@0033mer
@0033mer 4 жыл бұрын
Glad it was helpful!
@xolove3435
@xolove3435 3 жыл бұрын
I Watched this KZbin video by Mr. Maker ....How to make Mp3 player at Home ! I really want to make this but I'm having a hard time getting this type of pcb board! Is there an alternative ?
@javiergomez8064
@javiergomez8064 4 жыл бұрын
Using the Veroboard, how did you isolate the 10 header pins on the top middle of the board?
@0033mer
@0033mer 4 жыл бұрын
Cut a narrow isolation channel using a Xacto knife. It takes a bit of practice. If you cannot make that work you can buy 10 pin headers that will straddle the Vero strip. store.qkits.com/technological-arts/idc-ribbon-cable-to-breadboard-adaptor-10-pin-adidc10-m.html
@thepike100
@thepike100 3 жыл бұрын
Thanks. Is there a prefered board for power circuirs? 2A at 5v.
@0033mer
@0033mer 3 жыл бұрын
To lower the resistance of the copper strips for larger current applications you can parallel the copper strips and add a layer of solder on the larger current circuits to cut down on strip heating. The strip board can handle 2 Amps but there will be some heating. kzbin.info/www/bejne/jYWcqYqvgbBgf8U
@thepike100
@thepike100 3 жыл бұрын
@@0033mer great 👍
@ObligedTester
@ObligedTester 5 жыл бұрын
Are there large protoboards with isolationchannels still available somewhere? They do not need to have edge connectors. But needs to be fairly large
@0033mer
@0033mer 5 жыл бұрын
They are harder to come by as PCB prototyping has become inexpensive with fast turnaround time. You can check with Vero Technologies or Vector Electronics. www.verotl.com/circuitboards/protoboards
@sirajthowfika5981
@sirajthowfika5981 11 ай бұрын
what board size sir using here? tell us early as possible i am eagerly waiting for ur response.........
@simplelyf4072
@simplelyf4072 5 жыл бұрын
I’m interested in trying wire wrapping as an alternative to soldering my arduino and small circuit projects. Any suggestions for making a starter kit of supplies that you can recommend? Thanks!!!
@0033mer
@0033mer 5 жыл бұрын
Get some bare perfboard, wire wrap sockets, wire wrap tool with 30 gauge wire to get started. www.nutsvolts.com/magazine/article/wire_wrap_is_alive_and_well Your local electronic supply store should have these items. www.leeselectronic.com
@simplelyf4072
@simplelyf4072 5 жыл бұрын
0033mer awesome , thanks for the great resources, I’m giving it a go!!!
@ailijic
@ailijic 3 жыл бұрын
Thank you so much, this is the next step I was looking for.
@0033mer
@0033mer 3 жыл бұрын
You are welcome!
@ChazzCoombes
@ChazzCoombes 6 жыл бұрын
Hi great vid, where did you get your bore tool from? Cheers
@0033mer
@0033mer 6 жыл бұрын
Here is a link: www.rpelectronics.com/r22-0239g-veroboard-cutting-tool.html
@blankstares4355
@blankstares4355 5 жыл бұрын
i have a small project. with everything working on the breadboard. now its time to transfer it to a circuit board like your examples and to install in an enclosure. I am totally brain-locked on how to take my components and wiring from the breadboard to the circuit board.
@0033mer
@0033mer 5 жыл бұрын
It gets easier with practice. Mount all your components on a piece of Vero stripboard similar to your breadboard layout. Use the boring tool to make isolation channels as necessary. Finish off with jumpers installed from the top.
@poofyswine1
@poofyswine1 2 жыл бұрын
in that very last board you showed what AWG wire is that ?
@0033mer
@0033mer 2 жыл бұрын
24 AWG
@AlMcElmon
@AlMcElmon 7 жыл бұрын
Could you post an amazon affiliate link to your favorite Vector / vero / stripboard? Most of the ones that I look at dont have the build in channels like the one in your video.
@0033mer
@0033mer 7 жыл бұрын
The part number for the Vero stripboard is: Vero 01-0021. Many large electronic supply companies should carry it. www.newark.com/vero/01-0021h/veroboard-121-92x101-6mm/dp/95M0362
@danielrine3103
@danielrine3103 6 жыл бұрын
Hi, I am a first time viewer and new to making projects using these type of boards. Great video for the beginner. One question, How did you create the isolation channels, can I use a small drill? Thank you for this video..... Have a nice day....
@0033mer
@0033mer 6 жыл бұрын
Yes .. you could use a small drill or you can buy a boring tool made for the Vero strip boards. Here is a link: www.rpelectronics.com/r22-0239g-veroboard-cutting-tool.html
@ishubansal265
@ishubansal265 5 жыл бұрын
Very informative and good efforts.
@0033mer
@0033mer 5 жыл бұрын
Thanks for the feedback!
@gabejasso1747
@gabejasso1747 6 жыл бұрын
Hi, just curious, are there ways to cut vero board to smaller sizes from a large sheet at home?
@0033mer
@0033mer 6 жыл бұрын
Using a straight edge score both sides along a row of holes with a razor knife to get the desired size. Put the scored row along the edge of a table and push down to snap off the board.
@taranagnew436
@taranagnew436 3 жыл бұрын
what's the wide-isolated breadboard called and where can you buy them?
@0033mer
@0033mer 3 жыл бұрын
The company that makes them is no longer in business.
@peterfielden-weston7560
@peterfielden-weston7560 7 жыл бұрын
The "vector board" that you showed appeared to have more than 40 copper strips. Is that correct and when did you get them from? Thanks.
@0033mer
@0033mer 7 жыл бұрын
The board is actually called "Veroboard" or the generic name "Stripboard". I have a habit of calling all boards Vector boards. The two main companies making protoboards are Vector (USA) and Vero (UK). The board shown is 8X12 inch 78 strips, a size which is hard to find. I got it here: www.rpelectronics.com/prototyping/circuit-boards-busboard/thru-hole-boards They do not stock that size but if you look online you probably can find some with more than 40 strips.
@paulf1071
@paulf1071 5 жыл бұрын
Vector board == Veroboard?
@Emike-nc9ew
@Emike-nc9ew 4 жыл бұрын
Can the vectoboard be cut?.. I wanna try a project with it,but i dont know whre to start...
@0033mer
@0033mer 4 жыл бұрын
You can buy pre-cut vero/vectorboard that fit into standard enclosures or you can cut your own to fit. Score the top and bottom with a razor knife, put the score on the edge of your work-table and snap it off. www.rpelectronics.com/881-420306.html
@Emike-nc9ew
@Emike-nc9ew 4 жыл бұрын
@@0033mer thank you so much...
@ChargedPulsar
@ChargedPulsar 2 жыл бұрын
This is amazing, thank you. I have learned a lot!
@0033mer
@0033mer 2 жыл бұрын
Glad it was helpful!
@crispychickenwing
@crispychickenwing 3 жыл бұрын
can we solder modules like the hc05 and esp8266 to veroboard
@0033mer
@0033mer 3 жыл бұрын
Yes, they are .1 inch spacing so they will fit.
@crispychickenwing
@crispychickenwing 3 жыл бұрын
@@0033mer thank you 😁
@Mrcaffinebean
@Mrcaffinebean 11 ай бұрын
Great video, I learned a lot and subbed!
@0033mer
@0033mer 11 ай бұрын
Welcome to the channel!
@donaldreid8771
@donaldreid8771 7 жыл бұрын
Hi, I am trying to get hold of a board like the one you are holding at 45s. Does anyone know where I can get this ?
@0033mer
@0033mer 7 жыл бұрын
That particular board was originally from Radio Shack (Archer) back in the day. Proto boards like that are hard to find as chip manufacturers are dropping the DIP package and going surface mount. The best place to look is Vector Electronics: www.vectorelect.com/prototyping-boards.html Digi- Key is a distributor. Be aware, they will be pricey.
@leisergeist
@leisergeist 7 жыл бұрын
Thanks for the link, I've been trying to find a nice Eurocard board. In case you're still curious, these guys also sell a bunch of specialized protoboards, including one with an XT card edge connector like at 45s www.circuitspecialists.com/xt--bus-prototyping-boards
@cookiedee8473
@cookiedee8473 6 жыл бұрын
Awesome presentation!
@do7425
@do7425 3 жыл бұрын
I like your videos a lot, very informative👍🏼
@0033mer
@0033mer 3 жыл бұрын
Thanks for the feedback!
@LostieTrekieTechie
@LostieTrekieTechie 2 жыл бұрын
Thank you! Good overview
@notgay89
@notgay89 4 жыл бұрын
A informative and well made video thanks for your assistance.
@0033mer
@0033mer 4 жыл бұрын
Glad it was helpful!
@ericcsuf
@ericcsuf 4 жыл бұрын
Forgot all about flea clips! Nice overview.
@halldirector
@halldirector 8 жыл бұрын
Where did you get that tool to cut isolation channels in the veroboard? I just picked up some veroboard and I was going to use a dremel, but that tool looks less messy and more controllable. Great channel, btw.
@0033mer
@0033mer 8 жыл бұрын
Here is a link: www.rpelectronics.com/r22-0239g-veroboard-cutting-tool.html
@ruurdwiegers6274
@ruurdwiegers6274 2 жыл бұрын
You can also use a Stanley knife or similar for making the isolation channels. Tip is to plan your isolation channels first and cut them before soldering any components to the board.
@toddk283
@toddk283 6 жыл бұрын
Cool history lesson - Thanks for the info!
@jamesmyers2087
@jamesmyers2087 4 жыл бұрын
Freaking awesome, Sir. Very informative.
@0033mer
@0033mer 4 жыл бұрын
Glad it was helpful!
@nuwang1
@nuwang1 6 жыл бұрын
Thank you for being so informative
@the_irav
@the_irav 3 жыл бұрын
Never die, you legend....
@Duriel1000
@Duriel1000 4 жыл бұрын
Where do you get enclosures from?
@0033mer
@0033mer 4 жыл бұрын
Hammond Manufacturing: www.hammfg.com/electronics/small-case
@pebre79
@pebre79 7 жыл бұрын
Great info. thanks for posting, I really found it helpful.
@AndrewMurphy8383
@AndrewMurphy8383 4 жыл бұрын
you could also see those strips on old radios
@MegaCadr
@MegaCadr 4 жыл бұрын
How did I never realize that is why those enclosures had those ridges on the inside?!
@nurlatifahmohdnor8939
@nurlatifahmohdnor8939 3 жыл бұрын
I first used veroboard in 1996 for KHB (ERT). Cg Omar is Azlin, my classmate's father. Such a courageous male teacher. 13x40= 40. Roughly. Approximation.
@nurlatifahmohdnor8939
@nurlatifahmohdnor8939 3 жыл бұрын
62 students get all subjects A grade the following year. 1996+1 His daughter, my classmate went to MRSM|PC.
@chrislgr
@chrislgr Ай бұрын
Bravo Zulu!
@0033mer
@0033mer Ай бұрын
Thanks for the visit.
@jeanlucd2112
@jeanlucd2112 3 жыл бұрын
very good video
@Electronzap
@Electronzap 4 ай бұрын
Good info.
@0033mer
@0033mer 4 ай бұрын
Thanks for the feedback.
@ritvikvaishnav3472
@ritvikvaishnav3472 5 жыл бұрын
great vid, thanks a lot
@0033mer
@0033mer 5 жыл бұрын
You're welcome!
@Balu-7b7
@Balu-7b7 2 жыл бұрын
how-to soldering a ground terminal
@MikePoirier
@MikePoirier 4 жыл бұрын
VERY USEFUL, THANKS
@vanhetgoor
@vanhetgoor 2 жыл бұрын
Neither one of those boards was burned-up. How come? You never connected the power supply?
@malcwhite
@malcwhite 3 ай бұрын
By good design and careful application
@stryder751
@stryder751 5 жыл бұрын
Nice!
@GroovyVideo2
@GroovyVideo2 6 жыл бұрын
Thanks - good video
@49684
@49684 6 жыл бұрын
Are circuit boards copy righted?
@0033mer
@0033mer 6 жыл бұрын
That is a complex subject and would require a complex answer. IC manufacturers copyright their "mask works" used in the production of an Integrated Circuit.. A PCB is a different story with a lot of gray areas. Each individual case outcome would vary in a court of law.
@49684
@49684 6 жыл бұрын
0033mer Just curios, Thanks for answering. I have one more question: I’m 39, do you think it would be wise for me to get into electronics tech working for myself? I’ve been self employed for the last 10 years and couldn’t imagine working for anyone else.
@0033mer
@0033mer 6 жыл бұрын
I am retired and still do industrial electronic repairs and consulting. There are lots of opportunities out there if you are determined and willing to put in the time and effort. Check out my video: kzbin.info/www/bejne/bH66h3SeZrtkmZY
@billjensen51
@billjensen51 5 жыл бұрын
I think you should consider changing the title of your video. I did find it informative but not in a way I expected or hoped. Still, thank you for making this video.
@metamud8686
@metamud8686 2 жыл бұрын
This video is a nice introductory about (historic) options to prototype .. but I've yet to see the "prototyping tips and tricks" that were promised in the title. So I'm still calling it simple clickbait (unfortunately).
@0033mer
@0033mer 2 жыл бұрын
Almost every video on my channel is a "prototype" project, so look around, you might find something of interest. kzbin.info/www/bejne/i2rCYnSNmJyYaMU
@mihaiciornei5648
@mihaiciornei5648 6 жыл бұрын
TNK U . Very nice . Subscrybed.
@OninDynamics
@OninDynamics 4 жыл бұрын
1. do not solder stuff into breadboards.
@SuspendedNinth
@SuspendedNinth 7 жыл бұрын
I think you're canadian
@0033mer
@0033mer 7 жыл бұрын
You are correct .. I am canadian. What gave it away? :o)
@SuspendedNinth
@SuspendedNinth 7 жыл бұрын
the o in breadboard. Grew up in new brunswick
@G1ZQCArtwork
@G1ZQCArtwork 6 жыл бұрын
I can't watch these videos because of an inherent grammatical error. It is NOT sodder, it is solder, it has a letter "L". Please respect the English language better.
@0033mer
@0033mer 6 жыл бұрын
The word "solder" comes from the french word "soudure" which we get the verb "souder" I am Canadian with french heritage so the "l" is silent like in the word "salmon" The word can be pronounced both ways depending if you live in the UK or North America. dictionary.cambridge.org/dictionary/english/solder I am certified in soldering by Pace who are involved in university training and companies like NASA. Pace and the manufacture Kester pronounce solder with a silent "l". kzbin.info/www/bejne/rHq3ZaWXa7KiZtU I am sure the viewers understand both pronunciations.
@BertGrink
@BertGrink 6 жыл бұрын
In my personal opinion, it isn't really important how you pronounce that word, this isn't an english class after all! ;) What *IS* important is getting the info about the electronics across to the viewer, in which you succeed very well. Greetings from Denmark.
@SpeccyMan
@SpeccyMan 6 жыл бұрын
If you must be pedantic then you should know it is an error in pronunciation, not an error in grammar! "Please respect the English language better."
Techniques and Strategies for Building Electronic Circuits
14:12
Leo's Bag of Tricks
Рет қаралды 308 М.
Quilt Challenge, No Skills, Just Luck#Funnyfamily #Partygames #Funny
00:32
Family Games Media
Рет қаралды 55 МЛН
We Attempted The Impossible 😱
00:54
Topper Guild
Рет қаралды 56 МЛН
黑天使只对C罗有感觉#short #angel #clown
00:39
Super Beauty team
Рет қаралды 36 МЛН
Правильный подход к детям
00:18
Beatrise
Рет қаралды 11 МЛН
Arduino Prototyping Techniques #104: Perfboard
7:42
Marc de Vinck
Рет қаралды 69 М.
Circuit Skills: Perfboard Prototyping
8:37
Make:
Рет қаралды 646 М.
DIY PCBs At Home (Single Sided Presensitized)
10:11
TechBuilder
Рет қаралды 1,3 МЛН
Breadboarding tips
20:16
Ben Eater
Рет қаралды 450 М.
DIY PCB Toner Transfer (No Heat) & Etching
12:12
Gareth Burrows
Рет қаралды 1,5 МЛН
RP2350 GPIO Latch-up Glitch / Pico2
6:44
0033mer
Рет қаралды 3,5 М.
How to Solder properly || Through-hole (THT) & Surface-mount (SMD)
11:08
Quilt Challenge, No Skills, Just Luck#Funnyfamily #Partygames #Funny
00:32
Family Games Media
Рет қаралды 55 МЛН