CLAMP UNIT DESIGN | BIW FIXTURE | CATIA

[@rajeshjejurkar26]

Make more videos on fixture and gauge design.... will be lot of helpful

[@caddscience8822]

sure, will upload more videos on this topic

[@emirrasgido9033]

Thank you crack!!! Best regard from Argentina 🫶🏻

[@caddscience8822]

So glad to see someone from overseas, Thank you !!

[@mayurshinde7361]

Axis system symbol not shown at my system 3:35 .

[@caddscience8822]

may be this will help www.learnvern.com/catia-course/reference-axis

[@Raja_Ram19]

Sir how can download this type panel for precticing in my system

[@caddscience8822]

Check in grabcad website, you'll find some

[@RakeshSurathma]

PLP points are decided by the BIW fixture Designer or somebody else sir..?

[@caddscience8822]

In the car panel drawing pin location hole details will be given, for NC (mylar) we can decide depends on requiremnt

[@ashokchakravarthi8465]

can you please share the cylinder and clamp arm links to download?

[@caddscience8822]

There are many cylinder makers like smc tunkers destaco you can visit their official website and download, this link is to tunkers cylinders and clamp arms www.tuenkers.com/publish/92342d91_da54_cb89_add9bde5c193b028.cfm?l1=Clamping

[@ManivannanK-kf5ee]

Why you are not using coincidence command, offset command in assembly design.

[@caddscience8822]

Assembly constraints are not much used in catia as snapping is very easier and faster

[@anwarbraham9549]

In companies that work on large assemblies on CATIA, they prefer not using constrains because it would create update loops that will take a lot of time, instead they use a common axis system for all the parts, then design them in their final position so when you bring the part in the assembly is will come in its good position. If the part is used in different positions they would just snap it to the other position without constrains I hope this helps

[@KarthickR-tt7yb]

Make more tutorial videos for Biw fixture design

[@caddscience8822]

sure !!

[@newtechnology9263]

In two way shimming firstly said one is horizontal (-) and vertical side( | )shimming but later you said chopping side (perpendicular) shimming why sir

[@caddscience8822]

Hi, shimming should always be parallel or perpendicular to principal planes, please mention the time where I said perpendicular to chopping, I will explain, thanks

[@newtechnology9263]

​@@caddscience8822 no sir, I am asking one default x direction shimming and another one coming z direction shimming why sir , I believe that x and y direction shimming required not in z direction please clarify sir

[@caddscience8822]

Ok i understood your concern, default shimming is the nearest principal plane for the chopping, it can be x y or z

[@newtechnology9263]

@@caddscience8822 in two way shimming we can take xy or xz if x is default direction shimming,thank you for clarifying sir

[@caddscience8822]

@@newtechnology9263 yes, if x is default direction and less than 15 degree then only x direction is enough, I will also upload video on shimming very soon, please watch it for more information on shimming

[@RAhinr214]

bro could you give the website for downloading the panel

[@caddscience8822]

I downloaded it from grabcad, you can check there

[@manasops4372]

Make more videos, me and my friend waiting for your next videos, really This type of video we need for study, but this type of videos not found on KZbin

[@caddscience8822]

sure, will upload more on this topic

[@abhigowda8376]

❤❤tq bro

[@caddscience8822]

welcome, hope it helped

[@jyotibakesarkar1590]

Make more videos sir😊

[@caddscience8822]

Sure !! Planning to do next video on cylinder selection