✨ATTENTION - If you need help with your machine head over to our Discord. Anyone welcome - discord.gg/cGtudQthh4 ✨
@ProfileP246 Жыл бұрын
This is the best video by far for beginners, I’ve just put the machine together and about to get stuck in using the steps you’ve shown. Just what I needed Thanks!
@husondiy Жыл бұрын
No problem!! Glad it was of use to you 🤙🏻
@lazardan35895 күн бұрын
thanks for informations ,I recommend you to organize your desktop, you will find what you need faster .
@husondiy5 күн бұрын
Thank you 🤣. I like a challenge
@jc-pj3nh8 ай бұрын
Best learning video I have seen so far. Thanks Ben.
@husondiy8 ай бұрын
Thanks for the comment and feedback! Much appreciated 👍🏻
@moking8095 Жыл бұрын
Hi Ben, Things have been a little disjointed, which translates to " how the hell do I set this device up" and you have basically supplied the missing link. I now know how to set up the driver and the Universal g-code sender. You were a bit long-winded but you got there way before me. My only excuse is that I am 82 years old with fried brains due to overuse. Many thanks, Ben, you are my saviour.
@husondiy Жыл бұрын
Haha glad I could be of some assistance!! Have fun using your machine!!
@brassidium768611 ай бұрын
Excellent video.
@husondiy11 ай бұрын
Thank you very much!
@alandobb950 Жыл бұрын
Hi Ben, Santa bought me the Vivor 3018 CNC Router LASER Engraving machine for Christmas. I'll be following along with your videos once I've got the machine powered up (our son had a new puppy from Santa, so he, is taking some time up) it's a thumbs up & subscribe from me. Take care & I'll see you on the next one.
@husondiy Жыл бұрын
Awesome stuff Alan!! Glad to hear you've got some goodies for Xmas! Hope all is going well with the new puppy too 👍🏻🐕🦺
@d500-m2bАй бұрын
Hi! Can this machine NC software read canned cycles like G81 or G83? Thanks in advance for your reply!
@husondiyАй бұрын
Hi!! I have no idea to be honest with you, apologies
@salindaweerasinghe88806 ай бұрын
Hi Ben. I really thankful for this video. But i have some issues with TTC 3018 mashie. It's engraving switched left and write. And the output is so smaller than G-Code measurements. i can't even engrave 100mm. can you please help me with that 🙏
@husondiy6 ай бұрын
Have you tried re-cabling all connectors on the machine?
@kaloyanivanov4631 Жыл бұрын
Hello there! Have you managed to reduce the noise somehow. Mine sounds exactly the same way. I think its louder than it is supposed to be
@husondiy Жыл бұрын
Hello!! No I haven't unfortunately, still loud, especially on the harder materials
@Anomaly.Filmworks10 ай бұрын
Getting a higher Amp power supply can reduce the noise of the motor under a load.
@bromarbuildz-oy7ls Жыл бұрын
I recently bought one of these CNC 3018 pro machines. However it doesn't have any software drivers with it. I managed to get it from a college that were selling their tech equipment. Do you know where I can download the drivers?
@husondiy Жыл бұрын
Drop me an email at husondiy@gmail.com and I'll get you them sorted
@Stamering11 Жыл бұрын
Hi mate! Good video! I have bought this machine but unfortunately the delivered USB stick is corrupted so I don´t have the software available. Do you have any idea where I can download it or could you share it maybe somewhere for me? Thanks for helping, Johannes
@husondiy Жыл бұрын
Drop me an email to husondiy@gmail.com I can try help you
@Anomaly.Filmworks10 ай бұрын
Use a piece of paper when zeroing the Z axis. It should slip underneath until it's zeroed, will barely grip when zeroed.
@husondiy10 ай бұрын
Awesome!! Thanks for the tip, much appreciated 👍🏻
@paulbirmingham6444 Жыл бұрын
HI WHERE IS THE LNK FOR SOFTWARE UGS
@husondiy Жыл бұрын
Very good spot Paul, apologies I missed it from the description! Added now, and here for reference winder.github.io/ugs_website/download/
@timhicks1118 Жыл бұрын
Every time I try using ugs different things happen. Sometimes it will not move in any direction. Trying to run a program it just sets there doing nothing but looks to be running on ugs. I’m so frustrated with this 3018 pro. Any idea what to do?
@husondiy Жыл бұрын
What cable are you using to connect between your PC and the machine?
@timhicks1118 Жыл бұрын
USB cable to mini b to control board
@husondiy Жыл бұрын
Maybe worth trying a different cable!? Wonder if something wrong with it?
@250smacks9 ай бұрын
So do u use grbl or this ugs?
@husondiy9 ай бұрын
UGS 👍🏻
@dieterkrause1674 Жыл бұрын
UGS causes interrupting connection permanently...
@husondiy Жыл бұрын
You having problems still?
@doityourself52645 ай бұрын
will the same file work for a Mac?
@husondiy5 ай бұрын
Hello!!! I'm not sure it can be. But I've not tested so can't confirm 100%