ColourSpace Probe Matching

  Рет қаралды 3,019

Light Illusion

Light Illusion

Күн бұрын

Пікірлер: 14
@Mike-vb6qw
@Mike-vb6qw 2 жыл бұрын
Your videos are an excellent resource. If I am doing a 1D LUT followed by a 3D LUT for a JVC projector would the MPVM only be done on the 3D characterization prior to LUT generation?
@LightIllusion
@LightIllusion 2 жыл бұрын
Probe Matching must be applied to all measurements made to generate any LUT used for calibration on a given display.
@necahot2354
@necahot2354 4 жыл бұрын
Very detailed guide, thanks for your attribution
@LightIllusion
@LightIllusion 3 жыл бұрын
Glad it was helpful!
@optimalsettings
@optimalsettings Жыл бұрын
Thnaks. Don't understand 13:44? I have to do a probe match after calibration???
@LightIllusion
@LightIllusion Жыл бұрын
As it says, if the gamut changes dramatically, it is best to match probes on the reduced gamut. As with ColourSpace probe matching can be done any time - retrospectively for example - it is a simple process to perform. You can then just re-generate the LUT, without any further profiling required. This is not possible with any alternative calibration system.
@optimalsettings
@optimalsettings 10 ай бұрын
Do i have to make a full ddc reset on a LG oled before profiling?
@elongatuspiranha
@elongatuspiranha 3 жыл бұрын
Does SDR probe matching work when your calibrating HDR too? Or do a separate HDR probe matching needed for HDR calibration?
@LightIllusion
@LightIllusion 3 жыл бұрын
Probe matching should be done on the display when in an uncalibrated, native state, so SDR vs. HRD is actually irrelevant. It's all the same - unless you are are using a WOLED, and then you need to make sure the probe matching is done when the displays is not set to a high peak luma, as all WOLEDs suffer gamut reduction with such high brightness settings.
@elongatuspiranha
@elongatuspiranha 3 жыл бұрын
@@LightIllusion Thank you for the quick reply and answer. Much appreciated!
@elongatuspiranha
@elongatuspiranha 3 жыл бұрын
Does it matter what nits the pattern is if I'm using an external pattern? Is 75% or 100% pattern preferred or does it matter? Thanks!
@LightIllusion
@LightIllusion 3 жыл бұрын
You should not use 100% as there may be channel clipping on the display.
@LextraGaming
@LextraGaming 2 жыл бұрын
1:50
@LightIllusion
@LightIllusion 2 жыл бұрын
Sorry, I have no idea what you mean?
ColourSpace Display Profiling
32:09
Light Illusion
Рет қаралды 3,7 М.
ColourSpace LUT Generation Menu
22:25
Light Illusion
Рет қаралды 1,9 М.
It works #beatbox #tiktok
00:34
BeatboxJCOP
Рет қаралды 41 МЛН
小丑女COCO的审判。#天使 #小丑 #超人不会飞
00:53
超人不会飞
Рет қаралды 16 МЛН
ColourSpace Probes Menu
9:52
Light Illusion
Рет қаралды 685
ColourSpace Manual Measure
13:50
Light Illusion
Рет қаралды 3,6 М.
DEAD Game Boy DMG - Can I Restore it?
19:40
Bricoda
Рет қаралды 16
ST2084 PQ HDR
15:37
Light Illusion
Рет қаралды 2,5 М.
Sneak Peek
4:07
Light Illusion
Рет қаралды 599
FALD Display Issues (static image test)
0:53
Light Illusion
Рет қаралды 1 М.
It works #beatbox #tiktok
00:34
BeatboxJCOP
Рет қаралды 41 МЛН