Compressed Air Cutting | Fiber Laser Cutter

[@shivakumara6570]

Hello mam firstly thank you for your valuable suggestions it will hepls lot. In our facility, we have a 3000W laser machine with an IPG source and a 16-bar screw compressor. However, while cutting 2mm iron steel, we are observing burr formation. Could you please suggest the best solution to address this issue?" Let me know if I can assist further with technical adjustments!

[@ClaraChai]

what parameters? what nozzle?

[@michaelussher7627]

Please a link to the compressed air parameter library

[@ClaraChai]

A video of mine,please find it.

[@michaelussher7627]

@@ClaraChai I can’t find it that is why I need the link please

[@ClaraChai]

@@michaelussher7627 kzbin.info/www/bejne/gn6VgaODfdiijKs

[@afdbent9148]

@@ClaraChai do u have company here in the philippines?

[@estifanos7t6ayalew72]

Please can we get parameter for compressed air. the video that you suggest is all about oxigine and Nitrogen parameter

[@عبدالاهجهانشاهیافشار]

Hi . I have a question . My machine doesn't work properly and The fualt is professional valve

[@ClaraChai]

No gas?

[@d.dineshkumar2477]

Hi i hope you fine, we have 1kw laser cutting machine 16bar compressor 74cfm past 4 months we are facing moisture issue in bottom lens we check with compressor person and dryer as per their statement all are working fine we use GI pipeline is it correct? please suggest with pipeline should use like ss (grade?) or aluminium

[@ClaraChai]

There is water in air.

[@d.dineshkumar2477]

my doubt is the compressor to the laser machine we use the GI pipeline is it ok or not, if we need to change the pipeline so ss (what grade we need to use)

[@zilvinasimbrasas6845]

Hi, we ordered 1.5 kw fiber cutter and just would like to ask if it’s ok to use compressed air for cutting 1.5mm stainless steel, that would be pendants and will be polished with machines after cutting. Thank you very much 😊

[@ClaraChai]

I think it is okay

[@mr.surprise01]

Hi mam, at cypcut software, y axis not going origin, how it solve, At x axis value given 0 mm and At y Axis value given 100 mm ( how it zero)

[@michaelmisiolek3054]

Hi, I am looking to get a fiber laser. 1500 watt confuser on compressor size. I see allot of guys use compressors around 10 to 12 bar. Then the person selling machine says it has to be 16 bar compressor. I mainly cut 1 mm carbon steel. Can you tell me if the 12 bar is enough ? If so what is max material you can cut with a 12 bar compressor. Thanks

[@ClaraChai]

From my experience, 12 bar is okay for 1mm CS.

[@lasercuttingsolutionspakis6422]

Hi . Good day . Does the room temperature effect the compressed air. Means my dryer works proper but when I apply the nozzle more then 2.0 single diameter then the compressor runs constantly due to more air flow the lens gets wet. Any solution?

[@lasercuttingsolutionspakis6422]

Please I am waiting for your kind reply. Thankyou.

[@ClaraChai]

It is because the temperature difference between your chiller and room, make them two as close as possible.

[@RajaramVishwakarmavraja7]

How much Hp and Cfm is required for 6kw laser cutting machine with raytool 115 3.0 head

[@ClaraChai]

You can check my video of parameters.

[@sanilkumarsanal8353]

me 1 year finish cutting by air but last week ⏰ laser pulse less, [i p g laser ] laser /air problem no cutting now?

[@ClaraChai]

Contact your supplier if in warranty.

[@sanilkumarsanal8353]

@@ClaraChai Thanks

[@rahulbansal1198]

If the laser machine is 1.5kw and metal thickness is 0.8mm, is compressed air is better than oxygen??

[@ClaraChai]

What material? Carbon Steel? it is okay, but if you want a high brightness cutting section, I think oxygen is better. It depends on what result you are expecting.

[@ediscolovic531]

why is it shown to me (ftc sma wire or ceramic body alarm) I checked everything, it's not even up to the ceramic ring and I replaced the cable? @clara chai

[@ClaraChai]

Is the wire damaged? Tried to replace one?

[@ediscolovic531]

@@ClaraChai I replaced the wire, and the ceramic ring, but again the same

[@ClaraChai]

@@ediscolovic531 what is the alarm? Please get to me on WhatsApp. [phone]

[@saurabhkadam9012]

❤

[@عبدالاهجهانشاهیافشار]

And . My cnc machine is darox Yashkawa

[@ClaraChai]

Good to know.