Everyone wants to “wet it up” how bout you order a flowable mix from the start.
@altonwingate63394 жыл бұрын
how about you find a new job if youre juat gonna bitch
@jerryperez27864 жыл бұрын
When your truck gets rejected you’ll be the one bitching. Order a flowable mix if you need one. It’s so easy, but then again if you don’t know how to ask. Don’t keep going thru life trying to put a square peg in a round hole. Ignorance is bliss
@jogmas124 жыл бұрын
Or use a pump
@mikeochoa4584 жыл бұрын
Talk about no Slump
@transam45554 жыл бұрын
It's clearly could have been a rookie driver error, and not prepping the slump to the correct spec
@chrisbroesky29328 жыл бұрын
0" slump lol. Add WATER.
@wencemedrano72436 жыл бұрын
CHRIS BROESKY lol
@ramblin_man232 жыл бұрын
Looks like they needed it dry just in that one spot though.
@johnc6042 Жыл бұрын
This must be a Friday afternoon job that dispatched at 4pm😂
@Raymond-wq2bp2 ай бұрын
😂😂😂😂😂
@jeffharper75799 күн бұрын
Years ago I did Foundation coating and they was pouring the floor and one new driver left the water on the hole way to job site, yeah a little to wet and had to dump it on the ground.
@johnc60429 күн бұрын
That’s a lot of water! 😂 I had one where a finisher turned the add valve on trying to get the sprayer hose to go and didn’t turn it off. I was watching the mix get wetter and wetter on a slab until I stopped got out and like “oh shit!”…guy denied it of course and said I must have done it. Damn crackheads
@johnc60429 күн бұрын
It was a mountain job so I only had like 8 yards on. 120 gallons of water! 😂
@jeffharper75799 күн бұрын
Oops!! We layed block and bricks and one so called contractor poured his footers really wet he called it even flow concrete but in 20 feet we used 8" on the corner leads but in the middle my boss had me mix up and batch of mortor really stiff because we use 4" block and 2" slabs and around a 1" joint on the first course, we have never seen a footer with that much of a hump in it. We poured his footers after that.
@prowannab5 жыл бұрын
Am I the only one that sees the 8" gap from the form board to the bottom? If they poured it at a 6-7 it would all run out!
@FTNDrew3 жыл бұрын
You can put plastic though. These guys are terrible
@ramblin_man232 жыл бұрын
They should've built it up with dirt, to keep the concrete from flowing out
@CarlosVargas-jp4wu2 жыл бұрын
Yo could also use plywood or pegboard
@jboardy54392 жыл бұрын
Nope. The concrete needs loads of water. That is a dry mix
@Spoons74146 жыл бұрын
I’m not even there. I’m in the comfort of my own home and I still threw a shovel and stormed off.
@Tictokshorts4 жыл бұрын
Just try being a mixer driver for a day.
@beavis4304 жыл бұрын
Or fired everyone
@mikeprimm40773 жыл бұрын
Or both. Ida walked off before the first plug was cleared. No way am I raking that shit everywhere. Mixer drivers, there are some great ones, they know who they are. Then, you have the ones that cause cold joints because they're fat ass is sitting in the gas station eating, or slowing the flow of trucks down because they are gabbing. Or the ones that just don't know what in the blue fuck they are doing. Companies don't help this either, it's so hard to get warm bodies to fill the seat, that they almost help propagate the problem. No training, just "oh you have a CDL and haven't killed anyone in the last 5 months" bam! , Hired. Never seen wet concrete before? Got a CDL ? BAM ! HIRED! here's a70 thousand pound truck with a high rotating center of gravity, Show up to a jobsite where through the lack of training, you have no fucking clue where to go, what to do, then when you inevitably start getting screamed at by the finishers because now your no clue having ass is costing everyone money and time, remember to call your company and thank them for the lack of training. It's gotta be rough. Sitting in your air conditioned truck while we work our guts out. Being able to pass anything but a gas station deli. Keep whining mixer boy
@AQLandscaping5 жыл бұрын
I guess the dispatcher at the plant thought he was joking when he said "give me 30 gallons"
@SootyMangabey.3 жыл бұрын
I've seen some mickey mouse forms in my days but that takes the damn cake... Defiantly the cheapest bid contractor.
@5610winston9 жыл бұрын
Rebar on the vapor barrier and wire mesh, not enough finishers, no place for the truck to discharge with enough pitch to the chute for the concrete to come down, they hadn't wet the chute down to cool it, concrete was flash setting, finishers didn't finish clearing the plug from the chute before multiple water additions. Did I miss anything?
@michaelmaxim72079 жыл бұрын
Your right on. 30 yrs doing that . Sad day for them
@jcanada68288 жыл бұрын
send the truck back and fire the driver
@5610winston8 жыл бұрын
How the hell did they plan to get the concrete all the way to the far end of the slab? A pump or a conveyor would have been a much better way to go.
@nlo1147 жыл бұрын
Sloppy mixer op didn't clean his chutes before pour started. 1:50 onward: Check-out the solid dried-on stuff when the camera looks up at the mix. No wonder it didn't flow.
@rustynail31595 жыл бұрын
I just made the same list as you did.
@callofthewild91757 жыл бұрын
Even I know that shit is too dry. I love all the technical comments from cementheads😄❤❤
@HollowPo1ntz3 жыл бұрын
Concrete
@ChavezConcrete9 жыл бұрын
Nothing is wrong with the concrete. The driver didn't clean his shoots from the last job (ever?) so it won't slide down. Compounding it, the slope, or lack there of. Its somewhat of a flat run and the fact that the chutes have dried concrete on it and you see whats happening. The concrete guys seem like they can't comprehend what the real problem is.
@smokedpickles44719 жыл бұрын
You have no idea. That concrete is set.
@5610winston8 жыл бұрын
Condition of the chutes is less the issue than the near-horizontal pitch of the chute. Concrete can't flow down the chute if there is no down there. On top of all that, look how far the center of the slab is from the edge of the forms. They need a creteveyor or a pump, and at least a half-dozen more finishers, and a vibratory screed.
@MrBat0007 жыл бұрын
no...there is not enough water in the cement mix... thats why its too thick and not flowing down.
@ihightreasoni6 жыл бұрын
That stuff's probably been in the drum for 45 minutes to an hour and it's already starting to kick and he should have added like 20 to 30 gallons of water right off the bat that s*** should flow out the shoot on its own without you even having to touch it at least in the beginning
@looseandsloppy24246 жыл бұрын
That shit is about a 3 slump which isn't going to slide down all those chutes it needs to be about a six slump. I do this stuff every single day for a living. And it's probably got accelerator in it which dries it up twice as fast.
@mauriciomorfin22213 жыл бұрын
Send me some concrete, go easy on the water, go crazy on the gravel.
@WeAreLegion19042 жыл бұрын
These videos cheer me up. Everyone knows that alot can go wrong with concrete but it's always good to know there are people like this. The formwork here would just rise up into the air if you made it wetter and the large holes at the bottom are already far to big. Besides that I do not know what kind of concrete that is but you cannot simply wet up concrete like that. The truck doesn't have enough water to make it run and by the time you have a garden hose ready it's already reacting. Pumps are dirt cheap.
@jaredlewis69352 жыл бұрын
Do what 😳 🤔 have you ever done concrete
@jaredlewis69352 жыл бұрын
Have you ever set forms?
@WeAreLegion19042 жыл бұрын
@@jaredlewis6935 Its my job.
@markrohrer44466 жыл бұрын
The blind leading the blind. The three stooges
@ReplayCentralIdiotsWork-tx6cv9 ай бұрын
The truck driver still stood there not knowing what to do?
@benclarke38809 жыл бұрын
Looks like a hot mix, your order was added to what was left in the bowl from the previous customer, makes the mud turn real quick, add atleast 10 litres per cubic meter to that and spin it up for Atleast 4 minutes, judging by the size of that slab you had 2-3 trucks?
@joekittle34072 жыл бұрын
Scratch that he will need more than 10 gal to fix that dry mess
@stalnaker5766 жыл бұрын
Two words for ya....self leveling.
@AQLandscaping4 жыл бұрын
Good enough slump for the state job lol
@prlocc18824 жыл бұрын
I think every mixer driver should know when a customer ask for 10 gallons you double it. Who knows what these guys ordered for him to take it that dry 🤷🏻♂️
@TheBignuts9254 жыл бұрын
Dude just looks at his chutes overflowing like yup that's happening oh well let these guys handle it and u no after hes done hes gonna say is it cool to rince all my chutes down on the grass
@SootyMangabey.3 жыл бұрын
Amen, once i knew the customers I was pouring for I would always leave wet.. saved time having to wait to add 20 or 30 gallons
@tzimiz772 жыл бұрын
Its a damn yard, you should make it like soup.....
@gainsforjesus11642 жыл бұрын
Now why in the world would they order a 1 -2 inch ??? Argos just chillin letting them work!
@Belting1013 ай бұрын
That stuffs already started going off and the more he adds water the worse it will get because he will be outta water in no time and the slump won’t change at all
@Belting1013 ай бұрын
I’d say throw the sugar and or coke to it and caller quits
@johnnybenson60449 жыл бұрын
Put 25 gallons in it dummy!
@dakotadakota2735 жыл бұрын
20 max if you care about it
@natep.84524 жыл бұрын
@@dakotadakota273 I care about getting the load out of my drum. I'll dump my whole water tank into 5 yards if I have to.
@rhillzbob4 ай бұрын
forgot to turn on his water pressure tank valve daa
@jeffcaffrey70 Жыл бұрын
It’s not the concrete truck driver fault that isn’t flowing it’s because it’s too dry. The only thing he could if done different is wet his chutes before hand
@nationalwashproducts21246 жыл бұрын
What was the time stamp on that ticket?? After 90 minutes the trucks batch will start to set up and No amount of water added will save it
@devilmonkey7 жыл бұрын
to dry, should have no problem flowing at that pitch.
@MrBat0007 жыл бұрын
no experience what so ever! The cement mix is wrong and there is not enough water! all they had to do is add water to the mix in the truck....that will soften the flow. The driver of the truck is standing like a statue and doesnt have a clue. thats a complete fail.
@KylexSheppard4 жыл бұрын
good ol 1 slumper
@ravemaster74059 ай бұрын
What slump did they order the mud at? i've been on jobs with 10 yards where they order it at curb mud level and then they tell me they want a 6 inch slump and they got 1 percent in it. I'll add a gallon of super and add it onto their ticket whether they like it or not and throw 25 gallons in it.
@Gears.and.Gadgets9 жыл бұрын
This is one slow concrete pour...
@immortalhour38883 жыл бұрын
Argos at their best 😂
@mlr061219745 жыл бұрын
Looks like a load of wet base Put 30 in and blow it over the sides of the chutes. Or just put a slick pack in the mix 😆
@jasonharper26013 жыл бұрын
STUFF IS GOING TO BE SET UP BEFORE THE POUR IS DONE
@robertambrose53484 жыл бұрын
It's not the cement truck driver fault is actually the finishes fault
@johngiroux16619 ай бұрын
That was dry as hell. Like a 2 or 3 inch slump.
@Kydenhall11 ай бұрын
Jeez what mix is this. He doesn’t even hold that much water most likely. And thats coming from a guy who carries 2 tanks on his truck. Batch mixer needed to add more aqua
@luiss43914 жыл бұрын
These are the types of typical know it all 🥴🤣🤣🤣
@kevinpickard76278 жыл бұрын
did he even wet the shute before hand looks bone dry
@tylerfox55348 жыл бұрын
no he didnt
@kevinpickard76278 жыл бұрын
+tyler fox that will be why it was sticking when we do concreting we have our barrows soaked and all the back of the mixer soked
@poopinfruz97717 жыл бұрын
I duno, We've had drivers forget to wet the chute but never seen this, hard to tell without putting a tool on it, but it looks like a dead batch, even if it wasnt it sure is after he added all that water
@abitacat7 жыл бұрын
Kyle Ranger C'est
@jimbeam55604 жыл бұрын
It was full of dried concrete he never washed it from the last job.that's why he is a dumb Ass it must be bare steel or it will never flow
@rubenvillarreal7752 жыл бұрын
He didn't look like he had water in that tank
@das_murks2 жыл бұрын
"Order fails"
@nickc27087 жыл бұрын
that's the driver's job.
@beavis4304 жыл бұрын
Here's what wrong,after dumping the concrete in the chute the first time,they should have scraped the dry mud out of the chute. And the second time.The driver doesn't have the Hopper up and he seems either lazy or he's new. The laborer should have had a shovel also and for the size of the job,there should have been at least 2 more guys. These two don't seem too ambitious either. This is a case of "You get what you pay for" I would be so pissed if this was my job site.
@ericswain707 жыл бұрын
soup'm up
@justinkase93454 жыл бұрын
Larry, Curly and Moe.
@XenferosGames9 жыл бұрын
I would have rejected that load. That's already partially set up.
@jenniferzhu1138 жыл бұрын
we suggest ADDFORCE self loading concrete mixer. you will know the real machines.
@yurok367 жыл бұрын
They put that sugar in there by accident
@eag14635 жыл бұрын
No Mamés 🤦🏼♂️
@kencraig73084 жыл бұрын
Maybe the driver didnt know if it was footing load or a top load. If the load tag says 4" slump then you better make sure its a 5" or more before leaving the temper station. That way by the time you get to the jobsite it doesnt take much to get what they want. Never leave the plant with a wet load or you can be rejected.
@stevengibson22512 жыл бұрын
Still, he should have easily been able to get the load up to a 6 or more, if needed with the water in his tank. Looks to me like he forgot to pressurize his water tank, and when he thought he was adding water he was just high spinning it with no water going into the drum.
@timnorman357510 ай бұрын
Looks like he didn't travel very far or his drum wasn't spinning in transit. It takes a minimum of 70 rotations to complete a mix.
@pattyleabo4268 жыл бұрын
lol nice and easy residential here. Yeah the (pours) move a little bit faster down here in Texas ;)
@ramblin_man232 жыл бұрын
They probably needed it dry right there where the gap is under the board, then they would wet it up to pour the rest. The problem is that angle is too steep for dry mud. If the finishers don't pull out that dry mud first the driver should have.
@Trenasist4 жыл бұрын
Better off sticking the hose in the bloody mixer not the pour. It's coming out DRY
@dacodamitchell14533 жыл бұрын
Up here the drivers show ya what they got and if it’s not up to what ya want they stop and spin the shit outta that drum til ya like it. Feel bad for those boys I woulda said fuck you im out lol
@tylerfox55349 жыл бұрын
If you guys would please subscribe for more videos
@1971dave7 жыл бұрын
I would have turned the truck away, slump was about 45 were as 120 is max, pulling it down the shoot and spreading it, I like to see what the finish was like, why he had his float in back pocket,
@elchapo93276 жыл бұрын
Obviously his water valve is clogged and it’s not adding water
@sawltydawgchris61166 жыл бұрын
Is that driver trying to conserve water or are those finishers just plain stupid? Add water and give it 10. 5 inch slump is an acceptable slump requirement to finish a flat deck like this especially when you have the mixer chutes elevated like that and it will stack. That looked like a 3 inch and they are killing themselves while the mud is already setting off! I'm a veteran concrete worker and the key to this and all construction is work smarter, not harder and you get the job done. Not harder and waste time for a disaster!
@OhioValleyPress5 жыл бұрын
Had to be his first week
@roywilliams14169 жыл бұрын
just add some water driver. 10 ain't gonna touch that manhole mud. they need about a 6, 6 1/2"
@5610winston8 жыл бұрын
They have to work within the spec and the approved mix design. Look at the near-level pitch of the chute! Look how far the edge of the form is from the center of the slab! They needed a pump or a creteveyor to drop the concrete where they need it. A vibratory screed would take it from there. If they need a higher slump, they should have gotten approval for a mid-range or high-range water reducer.
@jaydoser7184 жыл бұрын
He didnt even throttle the barrel while mixing, get him outta here
@adriancastillo6730 Жыл бұрын
Wtf did I just watch
@EvilMoran8 жыл бұрын
work lazzy now others work hard dam!
@javiergomez72903 жыл бұрын
Hahaha stupid concrete guys, the driver mixing the concrete without adding any water, llol
@rjg5143 жыл бұрын
Need to wet the shoot down before you send concert down it
@SootyMangabey.3 жыл бұрын
its so dry it wouldn't matter.
@rjg5143 жыл бұрын
@@SootyMangabey. it would of help a little but not really with that dry shit lol
@zoltanember61556 жыл бұрын
Concrete mix fail, not more then one.
@frankcrum32335 жыл бұрын
He is not when is the type that is no good it’s too thick is coming up from the side anything it’s all inside the tank it’s all jacked up how are you I see you are you my senses and into yeah you see any other hola can you Siri I Love or is it the yellow key unlock
@christopherguerrero1924 жыл бұрын
Guess they were pouring curb!!!! SMH. Rookie
@capricornx73618 жыл бұрын
thats a bullshit slump wtf
@vortecmaxxx8 жыл бұрын
antonio bennett lmao
@frankcrum32335 жыл бұрын
Jelly I wanna let the Jelly for what are you doing with your satellite or you guys jelly love Jelly love
@rjg5145 жыл бұрын
Dam put water in that mud
@wencemedrano72436 жыл бұрын
No money for a pump!! Wtf lol
@tylerfox55349 жыл бұрын
Hey leave a comment or like for support thanks
@renatovazqez41995 жыл бұрын
Waaaaatrer bruh
@tylerfox55349 жыл бұрын
Hey guys leave a comment if what you think
@rideordie88227 жыл бұрын
add water and spray the shoot
@tylerfox55349 жыл бұрын
Hey please like the video for more
@JosePerez-ul1pr3 жыл бұрын
How is this a fail!?
@ansarullah1576 Жыл бұрын
Me Mixer truck driver my from Bangladesh I'm interested job
@andreacastaldi1049 Жыл бұрын
Change job truck driver....
@realeyesrealise89335 жыл бұрын
What a waste of 6 min 30 sec
@frankcrum32335 жыл бұрын
We’re going to sickness I kind a love Bruce I said take that brought the truck out here imagine I have Bruce any Volvo with Willis is these are your two Hebrews and you guys look at that you guys all like no it’s a get it are you Hebrews
@tylerfox55349 жыл бұрын
Georgia
@tylerfox55348 жыл бұрын
cement
@strengr8 жыл бұрын
cement is a component of concrete. Cement itself is nothing, it's limestone and water. Concrete is the actual word.
@armouredthug51548 жыл бұрын
10 slump for you :P
@RavagHer6 жыл бұрын
Add more water....shit
@Bassmastr-ly5vf6 жыл бұрын
I’ll bet it says 5 inch slump on his ticket. But yet he brings it at a zero. Get it to a 7 and let it fly.
@joeyparsley23785 жыл бұрын
Yep. They never pour what it says on the ticket. He should have raked down the first stuff. Guess he didn't look at it before he left
@concreteman87775 жыл бұрын
Shit if i know its a house slap 7 half baby no matter what
@concreteman87775 жыл бұрын
@captain poopy pants bro all the time
@natep.84524 жыл бұрын
1200 - 1300 on the meter never lets you down and hardly gets you rejected...unless its shotcrete and you didn't know
@thecorpse19703 жыл бұрын
i like 7 better
@dani_del03410 ай бұрын
Order it wet if y’all don’t want problems like these
@HumanAnaesthetic7 жыл бұрын
The truck driver is still standing there looking clueless til this day.
@jdiaz97597 жыл бұрын
😂😂
@Teadon863 жыл бұрын
The issue is the guy who ordered that concrete, he should have ordered a wet mix the cheap bastard.
@immortalhour38883 жыл бұрын
Looks like hot concrete
@ramblin_man232 жыл бұрын
Ain't the driver's fault
@danielhayes7352 жыл бұрын
@@ramblin_man23 could be, depending on what the requested slump was. Could have locked the chute for them at least though.
@anthonyvasquez67808 жыл бұрын
worst Mixer Operator EVER !!!! hahaha
@stevenstine11209 жыл бұрын
Many factors could contrbute to this fail. What you dont see is how long was the trk on the job? Could be a high psi load. It could have an accelerator admix added to the load. Driver error (not knowing his slump,getting lost going to the job). High ambient temperature.
@walsh93546 жыл бұрын
Steven Stine have you ever worked with concrete ? Psi has nothing to do with the f** barrel
@sawltydawgchris61166 жыл бұрын
That is a very likely factor being that it appears to be a deck poor where is it it's a high psi usually 3000 or greater and it's possible that it contains an admix like adva which a gallon can thin the mix down equivalent to 2 gallons but will also set that mud off like a firecracker in over an hour. Often a dispatch ticketing error for sending the driver out with that kind of mix design for a ride that is so long to time it out.
@johnjimjam12344 жыл бұрын
Not enough water for that heat. The chute wasn’t scraped and cleaned eithee
@ctg53765 жыл бұрын
Forms covers only the upper part of the slab ,in order the concrete not to run under the form they required tight mix , but not that tight. A 5" slump would be ok with a wet shute.
@stevengibson22512 жыл бұрын
Looks to me like he forgot to pressurize his water tank. For the amount of water, he should have been adding it didn't appear to be changing the slump at all.
@lucasmorris51114 жыл бұрын
At least you didn't have our guy " to wet Chet" always shows up with a 6 slump.
@mvasqu762 Жыл бұрын
🤣🤣🤣 that's a good one. Gotta use that on one of our guys
@nyhotdogsauce2 жыл бұрын
MAN ADD SOME FUCKING WATER!!! 30 GALLONS!!!
@BTubbs5 жыл бұрын
This is every driver for Argos in Jacksonville Florida! We even gotta driver named Can't Get Right!
@peytonhemi3 жыл бұрын
In Houston we have 3 named Can’t Get Right
@VWRICH233 жыл бұрын
@@peytonhemi lol Tampa argos here
@mikeprimm40773 жыл бұрын
HA ,Argos in Port Charlotte fl .Could fuck up an orgasm. Only use them as a last resort,. Coast concrete isn't bad as far as drivers go but, dispatcher isn't too smart.. put 50+ on the ground Friday, our 5 back to back trucks showed up an hour apart. Grrrrrr
@Ratlife7243 жыл бұрын
@@mikeprimm4077 Lol Argos is Sarasota FL is the same way! We use coast now
@Teadon865 жыл бұрын
Why did they order such thick concrete? Why not order concrete a bit more wet than that chunky gruel? Adding water is usually a bad idea, and more often than not the driver is not allowed to make such a decision without the plant's/mixer's permission, for if the driver makes the decision on his/her own then there's a good chance the driver will be responsible for any reimbursements. Basically, the fault lies with the buyer, possible the mixer too, who for some reason thought it splendid an idea to have some poor driver trying to solve an issue he did not himself cause. And another thing. When people are criticizing his drop I wonder if they've considered whether he can raise the truck or not or whether he is not allowed or physically capable to inch closer as to give him the possibility to increase the drop? Just figuring a bit here. I know a few people who have no way of raising their trucks to increase the drop for the concrete as to have it slide faster down the glide, yet people are treating this as the driver's fault when the thick concrete is not sliding down fast enough for their liking.