CCNA Routing and Switching: Configure EtherChannel (PAgP and LACP) in Packet Tracer
Пікірлер: 39
@siredogitto8801 Жыл бұрын
Man you saved me, I was just looking for a tutorial to explain to me these configurations and a friend recommended me this video. Thanks a lot!
@TechAcad Жыл бұрын
Glad it helped!
@TheToxicDave4 жыл бұрын
The video is great man. You explain it clearly and I like the point "Now we verify the configuration..." :)
@TechAcad4 жыл бұрын
Thank you so much my dear Friend for your great support...
@Impact4ever6 жыл бұрын
i was just reading about the subject in a Cisco press book, thanks for being so clear, its very helpful.
@TechAcad6 жыл бұрын
Thank you
@Siva11802 жыл бұрын
Yeah thats true
@williesolomon6142 жыл бұрын
Impressive video tutorial. Thank you for sharing. God bless you.
@TechAcad2 жыл бұрын
So nice of you
@infopc-arieh63726 ай бұрын
Excellent ... well done ... with Scripts ...
@TechAcad6 ай бұрын
Glad you liked it!
@jabiralhujaifa Жыл бұрын
thanks a lot for the brief discussion
@prabhus80985 жыл бұрын
It's very useful,could upload more videos.. thanks
@TechAcad5 жыл бұрын
Thank you And I will upload more videos in forth coming days.
@dariiqali34862 жыл бұрын
Thank you this really helped me again
@TechAcad2 жыл бұрын
Glad it helped!
@iiN1GH7M4R3ii2 жыл бұрын
thank you tech acad!!!! i have a question... whats the difference between configuring a Port Channel group and choosing those interfaces? Example: conf t interface range fa 0/5-6 OR interface port-channel 3 whats the difference? thank you!!
@TechAcad2 жыл бұрын
Once you create the port channel, it will create the Port-Channel Interface. So if needed to make any changes on those bundled interfaces, configure the interface Port-Channel! Thanks for your great support and sharing my dear friend!
@thepuldarshana9056 Жыл бұрын
hi, So you go to port channel and make it mode trunk. that is ok. so does it need to go in to physical interface and make it trunk too ? thanks
@TechAcad Жыл бұрын
It will work both ways! Thank you so much for your great support and sharing my dear friend!
@M.Suliman242 жыл бұрын
thank you alot of -- how to check the result? the throughput and bandwidth?
@simbadurio4443 жыл бұрын
outstanding!
@TechAcad3 жыл бұрын
Glad you like it!
@amam16042 жыл бұрын
god bless u!!!!!!!!
@MochammadFajarKurniawan5 жыл бұрын
how to check the result? the throughput and bandwidth?
@thispakistani89242 жыл бұрын
When you run show spanning - tree command one of the link show block
@tatkimchhae37613 жыл бұрын
Why S1 to S3 not green?
@TechAcad3 жыл бұрын
You may seen the Amber or Orange color, because here STP blocks the redundant path to avoid loop!
@rasheedmalik65944 жыл бұрын
simulation could ve helped u explain in a better way about load balancing
@TechAcad4 жыл бұрын
Thank you so much my dear Friend for your great support...
@rasheedmalik65944 жыл бұрын
@@TechAcad anyways its still the best tut i ever had so far in etherchannel...Thumbs Up!!!
@adhithyaasharma473 жыл бұрын
you have thought pin to pin the video great and very informate can you please send the note of that common which you have write in the side
@TechAcad3 жыл бұрын
Glad you like it!
@adhithyaasharma473 жыл бұрын
@@TechAcad can you send me the note
@adhithyaasharma473 жыл бұрын
@@TechAcad can you send me note which you are used in the vedio