Connecting Rod Installation

[@oldcatmech]

One I built hundreds of these engines, and always put the journal at the bottom of stroke so to not fight the counterweights and can easily put on the caps! Two does not show pressing in the liner to seat it, want to make sure that filler band is all the way in! Also made two long puller bolts warped in shrink wrap to protect journal as I pulled down the piston group! Worked really well!

[@tradyboy6289]

How about liner protrusion..that one must check before putting the line with the seals?

[@Jungleland33]

Love the way he uses a blade to get the easily damaged bearings out of their plastic wrappings.

[@axtonpayton1852]

You all probably dont give a damn but does anybody know a tool to log back into an Instagram account? I was stupid lost my login password. I would love any help you can offer me

[@matiassantino4452]

@Axton Payton Instablaster =)

[@axtonpayton1852]

@Matias Santino Thanks for your reply. I found the site on google and im in the hacking process now. Looks like it's gonna take quite some time so I will reply here later with my results.

[@axtonpayton1852]

@Matias Santino It did the trick and I finally got access to my account again. Im so happy:D Thank you so much you really help me out !

[@matiassantino4452]

@Axton Payton you are welcome xD

[@TheMiningNoob]

The alignment dowel pins on the connecting rods aim upward towards the front of the engine, as they should. At 3:14 however, when the technician shows the cap, he is installing the cap with the dowel pin holes aiming downward toward the rear of the engine. They won't line up with each other.

[@CostexTractorParts]

Thank you for your comment and feedback!

[@jrschultz5196]

Did not check for liner protrusions they must be from 4 to 6 thousands or head gasket failure is a sure thing. This video is crap

[@CostexTractorParts]

This video was made to demonstrate how easy it is to install a cylinder pack, since the piston & rings are installed inside the liner right out of the box. You should always verify and check liner projection/protrusion. You can check out our video on Checking Liner Projection here: kzbin.info/www/bejne/gKOqloaqZbCma8k Thank you for watching.

[@dingpongchi632]

Using Torque wrench as a breaker bar for the 60 degrees?

[@brandoalindabos3893]

How much titing and main bearing sir

[@spykerbeukes6975]

The tangs are only for bearing positioning, bearing crush are responsible for bearings not to spin

[@CostexTractorParts]

Thank you for your imput! We also invite you to check out our website at www.costex.com

[@japhethmboya3615]

No the bearing Tang/fang is for bearing centralization in the connecting rod not to prevent bearing from rotating

[@Stoparts]

The best channel ! Bravo colleges...

[@jrflores814]

So they do everything right and professional but do degrees with torque wrench and give it about 60°

[@benjaminsardena770]

What is the position of piston?

[@brabuslgsonymansorytesla813]

Я ВАШИХ ФАНАТЫ ВЫ ЛУЧШИХ БЛОГИР Я ДВОРНИК МОСКВЕ BRABUS MANSORY

[@JorgeRodriguez-po7kx]

I like the way He Works Nice and Slow the way it should be

[@UniversalDiscovery]

Nice video boss

[@SandorVeres]

MTZ 1221 set to order??

[@adhyadhy8137]

Very good 👍

[@zawmin8602]

How can I contact I need CTP parts for 3406 engine ?

[@jxaxrxlx]

🤤I love new engine parts.

[@thomasidjitche6469]

Le travaill natirelle j'aime trop ça

[@maurialeflamer5261]

Amigos ,mi motor 3306 de inyección directa avienta mucho humo, moja las válvulas de escape, pero está anillado

[@Cp-jv6mf]

It’s suppose to be 90 degrees there was a typo in he’s script or they are different cus oem cat requires 90 degrees

[@randaroro384]

You in Europe succeed at Repair of the machine

[@zainpakistan1797]

Sir i suscribed your video and like it but nobody reply me i want gep 65 _3 perkins olupiyan 60 kva generator it is 4 cylinder plz make video on valve adjustment tappet and its firng order plz sir

[@jorgechalarca335]

¿ NO ES POSIBLE TRANSMITIR EN ESPAÑOL?

[@عبدالنبينصر-ش8ط]

❤

[@mdbadalmiah6808]

Please engine crankshaft and camshaft and pump full timing mark sent thank you Sir

[@abiezersalinas2890]

Asia qe lado apuntan las gias dela biela de un 3406 mecanico

[@harikantjagadish6006]

Final Torque applying method is wrong....

[@EtanyobereJoseph]

I'm enjoying this

[@zinou7836]

Je suis à la recherche d'un emploi et j'ai de l'expérience dans le domaine, si possible, j'attends votre réponse.

[@ضياءالعراقي-ق3ث]

ok vre good

[@Ebra1234]

need employ?

[@CostexTractorParts]

Hello and thank you for contacting us! In order for us to better assist you, please contact us directly at [e-mail]. Thanks!

[@abraju]

Beautiful

[@CAT_COACHING]

👏🏻👏🏻👏🏻

[@jeanjacquesdufrening240]

bom noite. Jean Jacques. mecani completo

[@detrasdecamaraselrealking4806]

almando caterpillar 3512

[@gorandiaye1470]

je travaille au Sénégal sur des d8n

[@johncholmes643]

That would be a 3400 series engine cowboy

[@BigBrex0124]

Need employees ?

[@CostexTractorParts]

Hello Antoun and thank you for your comment. For any questions or inquiries that you may have, please email us directly at [e-mail]. We also invite you to check out our website at www.costex.com

[@aliomar9241]

خوش كتر

[@MuhammadHussain-mp9fq]

Cat c15

[@christianrosales7959]

piezas alternativas para un motor CATERPILLAR?....JKAJKAJAJKA

[@Lenovo-wz7zr]

Montagem dos tandem motoniveladora

[@cheikhgaye9295]

séjoli

[@carlogambone8870]

Ok

[@adilfrix6119]

Volvo

[@sindycarranza8696]

P

[@CCCP1968]

These guys sucks. I’m way better at installing con rods

[@Cp-jv6mf]

It’s suppose to be 90 degrees there was a typo in he’s script or they are different cus oem cat requires 90 degrees

[@FIDAHUSSAIN-y7z]

❤