We usually use a gear puller but I like your method as well.
@miker86233 жыл бұрын
James Ladd. Where I work we have similar gearboxes. What is an easy way to install. I’m the real world they just don’t slide back on.
@Mohow-fv2vq10 ай бұрын
@@miker8623putting a bold with a big washer in the ax. And same principle as in video. And please use a lot of grease. It will help next time.
@78945612able3 ай бұрын
@@Mohow-fv2vq Anti-seize helps a lot.
@IngDzib Жыл бұрын
Thanks regards from Cancun
@joseenriqueagustin959710 ай бұрын
Me encanto la forma, que yo sepa debería salir deslizantes, ahora mi pregunta es la siguiente. ¿ Cómo encuentro las dimensiones correspondiente para fabricar este extractor?. Se me seria muy util ya que me dedico al mantenimiento de faja transportadora pero quiero realizar estos extractor, pero no se como buscar las dimensiones del reductor.
@180Floridalife10 ай бұрын
Ve a la página de la comunidad en mi canal y mira la publicación más reciente. Para fotos detalladas del motor extractor. gracias
@nacerayoub19636 ай бұрын
Un travail provisionnel, merci
@180Floridalife6 ай бұрын
de rien, merci d'avoir rejoint la chaîne
@shhmallbudoo23772 жыл бұрын
I put these on all the the time on conveyors. Mostly 107s
@hi-pwr11 ай бұрын
What are the dimensions of the screws you used in this ocassion?, by the way it looks in the video, plate thicknness is around ½ in. Also, if possible, do you remember what kind of style of screw is, standard, extra fine, etc?
@180Floridalife11 ай бұрын
The screw is from a puller set, i believe it was 1/2 fine thread. 12” long
@faroukalgawish52096 ай бұрын
Thanks
@somethinguseful29352 жыл бұрын
Thank you
@faroukalgawish52097 ай бұрын
Is this way having bad impact on hollow shaft bearings? I think this gearbox should be overhauled after dismounting this way
@180Floridalife7 ай бұрын
We have had no issues with gear boxes removed this way.
@Scousedave20058 ай бұрын
You got the dimensions as this be handy for me to make
@180Floridalife8 ай бұрын
If you go to the community tab of my channel there are some close up photos of the puller to help make your own. Have a great one ☝️
@bigstatercak21932 жыл бұрын
Cool
@180Floridalife2 жыл бұрын
Very cool indeed 👍 thanks for watching
@cheikhsidatydiop7521 Жыл бұрын
I need to see the plate . I want to bring out one of this more complicate
@180Floridalife Жыл бұрын
Check out some of my shorts for a Closer view of the puller
@180Floridalife Жыл бұрын
I have posted pictures of the plate on my channel under posts thanks
@miker86233 жыл бұрын
Do you have a video on how to put it back on
@180Floridalife3 жыл бұрын
I don’t but that’s a excellent idea for a new video. Thanks for watching
@amillimartin1456 Жыл бұрын
Can you show us the plate that you made please 🙏🏾
@180Floridalife Жыл бұрын
I’ll see if I can find some pictures and post them on the channel. There are some KZbin shorts on my channel that show it closer
@180Floridalife Жыл бұрын
I have posted pictures on my channel under posts, enjoy
@gmarine3572 жыл бұрын
Do you have more images of the plate.
@180Floridalife Жыл бұрын
I have posted pictures on my channel under posts
@kingsupra50232 жыл бұрын
Which Gearbox oil good for this Gearbox
@180Floridalife2 жыл бұрын
mobilgear oil 600 xp 220
@deadshotmotorsports78562 жыл бұрын
I would have like to have seen what the other end of the threaded rod, how dose it push on the pulley without hurting the roller.
@180Floridalife2 жыл бұрын
Thanks for watching, it’s a standard pusher rod, robbed out of a gear pulled, so the far end has a rotating flat head on it
@ronaldolopes2391 Жыл бұрын
How thick is the board in mm?
@ash63562 жыл бұрын
Is this tool available out there in the market?
@180Floridalife2 жыл бұрын
This is a shop made tool
@ash63562 жыл бұрын
@@180Floridalife cool!!
@selvamveerayah3052 жыл бұрын
can send me how the plate looks like sir/
@180Floridalife2 жыл бұрын
I’ll see if I can find the pictures
@180Floridalife Жыл бұрын
I have posted pictures on my channel under posts thanks
@javiermartinez19296 ай бұрын
Ya me habias espantado kimo
@180Floridalife6 ай бұрын
¡no temáis!
@Bigrig_trmc4 ай бұрын
Why not use an impact instead of a ratchet??? It’s wat I use cuz it works faster and less work lol
@180Floridalife3 ай бұрын
With the impact I would worry about damaging the shaft or the gearbox. Removing it by hand allows you to feel when something goes wrong, and lowers the chance of mushrooming the shaft. Thanks for watching and have a great one
@marouanattioui9031 Жыл бұрын
HELLO NICE WORK, COULD YOU PLEASE SEND ME THE PLATE
@180Floridalife Жыл бұрын
Sorry can’t sent the plate but there are detailed pictures in the community section of my channel. Thanks
@dhawk76286783 жыл бұрын
What's the purpose of the metal Jerry rig plate
@180Floridalife3 жыл бұрын
It is a gear puller used to pull the motor off the shaft. The motor and shaft take a set and are very hard to remove