Installed the CS pump internals today. This video was a great help and pulled me through a few rough spots. Thank you Corksport!
@90FirstGenPGT10 жыл бұрын
That engine bay is spotless!
@djmist4life10 жыл бұрын
Awesome work guys! Good thing I held off on buying any other HPFP, I will grab one for sure!
@AtticAZ9 жыл бұрын
It's still best to pull the blue "circuit" fuse, start the car and let it die before removing the battery cable to remove excess fuel in the line. Makes it much easier and safer. 🚗💨😉👍
@AtticAZ9 жыл бұрын
Just did my fuel pump internals. And apparently the circuit fuse trick to release the pump pressure does not work for gen1's. I pulled the circuit fuse, started the car and it just ran and ran. It really wasn't too my fuel spillage. Just need to have some rags handy. Even after starting the car three times to try to do the circuit fuse trick, it still wasn't too bad. Thanks Corksport for the install vid. It was great to use along side the white paper that came with the internals. 👍
@mase76199 жыл бұрын
Atticaz Just did my fuel pump internals. And apparently the circuit fuse trick to release the pump pressure does not work for gen1's. I pulled the circuit fuse, started the car and it just ran and ran. It really wasn't too much fuel spillage. you just need to have some rags handy. Even after starting the car three times to try to do the circuit fuse trick, it still wasn't too bad. As for the lower fuel line, I zip-tied mine, as to not lose it in the abyss. Thanks Corksport for the install vid. It was great to use along side the white paper that came with the internals. 👍
@PliskinHK2 ай бұрын
How did you get the high pressure fuel line back on? The nut doesnt meet up with the fuel pump even after bending
@fatsauze911510 жыл бұрын
Installed today! Video was a huge help. Thanks CorkSport
@b3astms3855 жыл бұрын
Literally just installed mine tonight, this video was a big help, is there any break in period after installation?
@santiagospangler19995 жыл бұрын
Stunner Gunner Yeah I believe 100 mile break in period
@randyfernandez1110 ай бұрын
The 17mm nut is it possibly for that to get loose and possibly leak fuel i recently had to take off my hpfp but it keeps leaking i make the 19mm is as tight as it can be the two plastic clips are also in place
@ReeshaRacing Жыл бұрын
i can’t get the fuel pump back in because it won’t aline with the main fuel line please help
@frowny-team18943 жыл бұрын
If I crossed threaded going into the fuel pump housing and slightly damaged it, I’m basically screwed right?
@djdecimation52892 жыл бұрын
I installed mine and the cam was locking up, why would this happen?
@laurenkelley71242 жыл бұрын
This is a great quality video I enjoyed watching it!
@israelvera49582 жыл бұрын
Buenas tardes!! Una pregunta?? Dónde puedo comprar el repuesto de bomba de gasolina para mazdaspeed6 2007??
@paagyantilifanica54853 жыл бұрын
Hey, the retainer clip for the blue fuel line ended up falling and getting lost.. is that something to worry about or is it not a big deal? sorry i’m pretty new to doing my own car stuff
@prof.mateoarroyocortes13853 жыл бұрын
Ustedes tienen el solenoide de la bomba de alta presión Mazda MZR 2.3 2007?
@collink71459 жыл бұрын
Why not pull the fuel pump fuse, start the car and let it run until it starves on fuel so there won't be any pressure behind the fuel pump?
@intertunetv9 жыл бұрын
if the battery is disconnected, since you are working on the fuel system - which is good practice... the fuse isn't doing anything important.
@guitarmatt08677 жыл бұрын
Collin Klopfenstein that's what you should do, I'm not sure why they didn't do that before unhooking the battery
@JoeGrow-pj3nr2 жыл бұрын
Hey my retainer and tappet are one ? Is this fine
@guster7306 жыл бұрын
Could I use sewing machine oil to lubricate the parts? That's what I use for the bov
@corksport6 жыл бұрын
We have not ever tried this...
@mzr35533 жыл бұрын
Does that internals have gold inside.coz its so expensive😀😀
@brotherhood_ofstreetracers42683 жыл бұрын
Only 350
@marcelolopez67974 жыл бұрын
buenas noches, en donde puedo conseguir el sensor de la bomba de alta presion mazda cx7 2008 turbo 2.3. ustedes lo venden y en cual es el precio ?
@stephenrios46429 жыл бұрын
Will this help with the HPFP chatter problems?
@horn25610 жыл бұрын
Will this work to convert the car to e85?
@GreenGenerationTV6 жыл бұрын
yes but youll need a tune
@sq33qs4 жыл бұрын
Video was helpful, thanks guys
@sq33qs4 жыл бұрын
Just got done installing an hour ago using this video as reference. Thank you guys once again.
@acemanz88810 жыл бұрын
what happens if you were to install this on a car with no other mods what so ever? would it be helpful? harmful? or just unnecessary? (ms6 for me)
@LancelotMooreYorke10 жыл бұрын
it would be fine if its your first mod, its needed anyways further down if you're doing more upgrades, but if you're leaving your car bone stock, dont bother installing it
@2AMech6 жыл бұрын
did you put the stock airbox around the aftermarket intake filter? that looks like a great idea for possibly keeping temps or dust down
@guitarmatt08676 жыл бұрын
Colin Shahan they sell a airbox for short ram intakes if I'm not mistaken
@icemn5 жыл бұрын
So what do you lubricate with oil and what do you lubricate with fuel 👀🙈
@corksport5 жыл бұрын
Just lubricate the whole thing with oil
@brianthiem92083 жыл бұрын
whats the lph?
@kewlkiddo2210 жыл бұрын
Do I need to install this if my only mods are short ram intake and cat back exhaust ?
@OGtrushalpatel3 жыл бұрын
It’s an essential mod regardless. Have you still got the car 6 years later lol?
@FuriousGerbil52 жыл бұрын
@@OGtrushalpatel I’m gonna be doing mine here this weekend as well as injector seals and cleaning the valves and injectors also changing the e slave cylinder
@sSHIFTIEe3 жыл бұрын
Should probably just buy a spare pump already fitted and then swap them out
@ENDxGamezZ9 жыл бұрын
Ok everything went fucking smooth except trying to get this pos pump back onto the car. Currently sitting on my driveway dead. The bottom fuel line is not fitting back into the pump and its extremely hard to get it to fit back in. any help please?
@AtticAZ9 жыл бұрын
Did you, eventually, get that fuel line back on?
@ENDxGamezZ9 жыл бұрын
Yeah i did, i had a leak at first but took the pump back out and put it in and it fixed it somehow lol probably misaligned a little idk
@ReeshaRacing Жыл бұрын
bro how did u do it im fucking dying tryna get it on
@felipeherrera61185 жыл бұрын
Question , i installed this on my car and now its ticking , however one thing i didnt to is put that metal bucket inside the fuel pump back again, if i kept it in i wouldnt let me put the fuel pump inside the housing . Is this something i need to be puting back in?
@corksport5 жыл бұрын
Can you shoot us an email to sales@corksport.com? That will be a better avenue to communicate and help you!
@corksport5 жыл бұрын
You need the lifter in the pump housing. Inspect the camshaft when you take it apart and make sure you did not damage the camshaft or the fuelpump internals.
@HUB19877 жыл бұрын
how did you tighten to 8ft-lbs with a normal wrench? also has anyone got any feedback to say bout this part is it good ? does the car fill better?
@nexa44986 жыл бұрын
With some wrist gauges. The part is really great, and easier to install than Autotech internals due to a more custom and complete design with the included spring and installation tool. Some people will say their car feels "smoother", but if this is your first mod (as it should be on a Gen 2) it's more for peace of mind and freedom to mod away in the future knowing your pump won't give out and let the car blow it's engine into bits.
@Monkee886 жыл бұрын
I bought a speed6 for about a year now came with some after market parts. I was wondering if there is a way to find out if the internal hpfp is swapped out.
@corksport6 жыл бұрын
There is no real way to determine for sure only based on the values from the Fuel Pressure Readings. You will want to remove the pump and inspect the internals yourself. Our internals have an octagonal bottom and a serial number. which tells you really quick. The auto techs have a dual retainer on top as well.
@Monkee886 жыл бұрын
Thanks
@chapinkonce2178 жыл бұрын
My car didnt turn on and white smoke after install, help.. !!
@markridgeway16798 жыл бұрын
don't buy shit! dumbass
@mgayar168 жыл бұрын
The smoke maybe too much oil and take it out and see what you did wrong disassemble it and try again
@marcoshernandez31044 жыл бұрын
Why is my car running rich after this😵🤦🏿♂️
@tjsmith94494 жыл бұрын
Better than lean man, maybe it needs a tune or new spark plugs
@OGtrushalpatel3 жыл бұрын
Don’t even stress, most likely coz you’re not tuned
@kewlkiddo2210 жыл бұрын
Do I need to install this if my only mods are short ram intake and cat back exhaust ?
@stevewk10 жыл бұрын
If those are the only mods you are going to do, then it really isn't necessary. If you change your downpipe, you will most definitely need it. The COBB AP3 is a great way to monitor your fuel flow...
@trevorshampy13158 жыл бұрын
+stevewk2009 False. You will definitely zzb if you don't do that. ANY mod too the motor besides a BPV you will need hpfp. Any mod that makes more hp will need it because the stock fuel internals can't keep up. fuel pressure drop ZZB. The stock fuel internals are very close to not being able to keep up stock.