Thank you for the video Zent. I performed this job on my C5 Z06 and it was not difficult. I used a Snap-on 24 mm deep offset wrench to rotate the crankshaft and that worked really well.
@426fourspeed6 жыл бұрын
Thanks for the quick, simple video for any moderately skilled home mechanic. New springs are CHEAP insurance for these cars. Consider doing a video on a BCM rebuild. Keep up the good work! -Jim
@ninjardr750r6 жыл бұрын
truly enjoying the C5 content!!!
@Faith0929ROK5 жыл бұрын
Good stuff man! Before this video, I was hesistant changing the springs on my 03 Z. Thanks again!!
@mikescotese6206 жыл бұрын
Awesome video. By far the best way to hold the valves up is the piston way like you do here. Way better than air cause it very difficult to screw the hose blindly into spark plug holes even though I have used air before on other cars with easier spark plug hole access. Never tired the rope method but it sounds cumbersome to me. Awesome the way you linked to parts and tool websites. Just completed this job on my 02 Z06. Did the 3 easiest to get to cylinders with air and the last 5 with your piston method. Again many thanks.
@elwennier266 жыл бұрын
Great video! You made it look so much easier to do! Thank you!
@dowroa6 жыл бұрын
Hmm... thanks... and while I need to do this with my '02, I would not use this as a guide. Just too quick, not enough shown and questions about why the keeper hardware was not replaced. Valve cover gaskets? How are you rotating the crank, etc. Great primer for the topic, but not stand alone.
@ZentRose6 жыл бұрын
No reason to replace my keepers, VCG, or other components unless lost or damaged. Valve springs are a maintenance item for a tracked Z. Intervals depend on how hard you run the car. Enjoy your Z!
@dowroa6 жыл бұрын
Agree. Not stating you don't know what you are doing. Just stating for the first time, it is much less so for myself. Thanks again, Zent.
@VetteDaily6 жыл бұрын
Bro...thank you so much for filming this, taking mine apart tomorrow.
@ZentRose6 жыл бұрын
Awesome. I hope it goes well!
@VetteDaily6 жыл бұрын
ZentRose hey man I started to rotate the engine until the Valve came back up, but the the retainers just popped out and went flying. Found them luckily, What did I do wrong to find TDC?
@ZentRose6 жыл бұрын
Interesting. The way I do this is to rotate the engine (slowly) enough to free the keepers and then pull the valve stem out by hand. I do it right at the 1:50 mark in this video. I'm glad you found your keepers!
@VetteDaily6 жыл бұрын
ZentRose yes, slowly is the key ha. I dropped a valve (F#@!) But then figured out by rotating the engine it'll push the Valve right up...Im so lucky. 8 down 8 to go. UPDATE : The last few were so easy I compressed the springs and very carefully turned it over and it just barely popped. So far the car runs smooth.
@TheGabe926 жыл бұрын
Damn these LS engines are easier to work on than most motors making half their power!
@BoltsNBoost3 жыл бұрын
Nice video. Make me much more confident in attempting this myself. How are you rotating the assembly?
@BenM4 жыл бұрын
Looks so easy compared to other motors wow
@bwill03z764 жыл бұрын
When you torqued the rocker arm bolts down did you not rotate the crank for each rocker to get the valve closed?
@wWLoganWw3 жыл бұрын
Very good, to the point, and detailed video. Question.. what keeps the valves from dropping and what's your easy way in getting engine TDC?
@Fmandan773 жыл бұрын
In the method he's using, the piston for the cylinder is at the top of the bore and prevents the valves from dropping. The big end of the valve is literally resting on the piston. There are a few different methods for making sure a piston is at TDC. I personally use compressed air, but in this video he warns against it. I agree this is a well done and edited video, very concise.
@Miokomata6 жыл бұрын
ty for the video. working on an 383 stroker for the first time :3
@KNS_Racing6 жыл бұрын
Excellent video. Helped me alot. Love how-to vids for the c5. Im interested on your thoughts on running a pcv catch can on these cars since they are known for flooding the intake manifold with oil when doing sustained high rpm driving.
@Thorsanbauer Жыл бұрын
what technique for top dead center? Do you use a special tool to get in because it's so tight on by the crankshaft. How do you know if the valves aren't up just because it's the trumpet combustion stroke
@Frbo19886 жыл бұрын
Thanks for the video!! This is something I am about to do before spring in my c5. !:) /Fredrik
@Z06GT16 жыл бұрын
Thank you Zent. I was planning on having this done at the dealer but you make it look easy so I will do it myself. I appreciate your videos.
@qzorn44402 жыл бұрын
great information... 😎 thanks
@jameskirby25732 жыл бұрын
Great video
@BenFreedmanRacing3 жыл бұрын
This is perfect
@damyrmonjaras77563 жыл бұрын
Can you crank the engine back up as is even tho the piston was on top dead center
@Z06GT16 жыл бұрын
Where did you get your spring compressor tool?
@sdlausen16 жыл бұрын
It would be great if you made a video of doing this on an ap1 S2000.
@jayala20073 жыл бұрын
Does it matter to torque the rocker arms when spring is decompressed?
@Ozhtube4 жыл бұрын
Did you drain the engine oil or disconnect the battery or you don't need to?
@markmoreno11155 жыл бұрын
Just to confirm. You compress the springs then rotate the engine to have the pistons push the valve and keeps out of the retainers?
@ZentRose5 жыл бұрын
Yes or use compressed air or set piston to top dead center before compressing.
@markmoreno11155 жыл бұрын
@@ZentRose the values don't drop when you compress the springs? I'm assuming the springs and valves are connected like when the engine is running but pushing the valve up with the piston pushes it up and out if the retainer? I'm just confirming before I lose a valve lol
@ZentRose5 жыл бұрын
Mine did not drop but I made sure the keepers and retainers remained seated on the valve. Yes, in this video I used the piston to push the valve and keepers up. I then removed the keepers and swapped the springs.
@mikehall5064 Жыл бұрын
Do the valve seal’s work on a ls1
@mikehall5064 Жыл бұрын
Just asking because Amazon says they won’t fit my 2000 corvette
@ZentRose Жыл бұрын
I thought they were all the same for chevy gen 3 small blocks but I could be wrong. It's been awhile since I've worked on one
@Z06GT16 жыл бұрын
How did you rotate the crankshaft? Were you able to get a socket on the front of the crank?
@ZentRose6 жыл бұрын
I know of three ways to rotate the engine (I have used all three of these methods on the C5 vettes): 1. Pull steering rack out of the way to access crank pulley. 2. Pull the spark plugs and use a wrench on the alternator pulley to rotate the engine. 3. Put car in sixth gear and rotate front tire by hand (by far the easiest method).
@Z06GT16 жыл бұрын
Thank you Zent. I appreciate your advice.
@sickboy36366 жыл бұрын
Rotate front tire? What are you talking about?....what good is rotating the front tire gonna do on a rwd car? Appreciate the content.....but a little confused by that.
@lancedolan6 жыл бұрын
He must have meant rotate rear tire
@stereolababy Жыл бұрын
@@sickboy3636 its on the ground. you can move any wheel by hand
@trevorcolin7555 жыл бұрын
I wish you showed how you cranked the motor. (Not with the key?) I'm not taking the balancer off! No one shows this part with the motor in tact. I've had these covers off so many times. Do you just crank the balancer bolt (in neutral) to the right? It's so hard to tell TDC. Im wanting to do this so badly
@ZentRose5 жыл бұрын
For this video I stuck the car in 6th and pushed it along the ground to turn the engine.
@trevorcolin7555 жыл бұрын
@@ZentRose wow! I'm doing the same way! Can you please elaborate a little on how you know you're close to tdc. When all the springs are evenly up?? Help? Thank you
@TheDaviro472 жыл бұрын
@@ZentRose I agree please elaborate, that's the only thing stopping me from doing it right now
@TheDaviro472 жыл бұрын
@@ZentRose so you compressed them down with the tool, then pushed the car In 6th till they popped up??? Also does the engine start up just fine after even if it's top dead center
@walterlangkowski47235 жыл бұрын
I’m kind of a noob but how are you finding your “top dead center”? By turning the crank bolt correct? Are you reusing your retainers?
@ZentRose5 жыл бұрын
You can turn the crank bolt but in this video I put the car in sixth gear and pushed it forward to rotate engine and find top dead center. Yes I reuse retainers. I just wanted to get rid of the yellow valve springs.
@gurnblanstein98164 жыл бұрын
Will the valves fall into the cylinder if you're not on top dead center?
@Teal2nnr4 жыл бұрын
Yes. If you're not using compressed air or the "rope" method, the only thing holding them in the head is the friction between the valve and the valve seal. If you're removing the valve seal, there is nothing at all to stop the valve from falling in.
@angellawless74135 жыл бұрын
Wait wait wait. Is it really that easy to get to the valve springs? I’ve seen other cars and you have to remove a lot of other things that are in the way first.
@ZentRose5 жыл бұрын
Yes the LS engines are very easy to work on.
@scottschneider45966 жыл бұрын
How did you rotate the engine? I know its a tight space in their with the steering rack in the way.
@ZentRose6 жыл бұрын
If you have trouble getting to the crank, you can throw it in 6th gear and push the car to rotate the engine.
@FerasDishli5 жыл бұрын
👍🏻
@lancedolan6 жыл бұрын
As an LS1 owner, how/when do we know that we should replace the springs
@angellawless74135 жыл бұрын
Lance Dolan on the ‘02-‘03 c5 z06’s there is a known/ well documented issue with the OEM valve springs failing. A lot of people change em out before they that happens. Way cheaper than buying a new engine.
@giyoon2156 жыл бұрын
For S2000, do you recommend changing springs while replacing the stem seals also? Or retainers?
@ZentRose6 жыл бұрын
Unless very high mileage, I reuse the old springs. On the AP1 you sometimes have to replace cracked retainers.
@giyoon2156 жыл бұрын
ZentRose , thanks for info. I might change springs at 400k mile service. Until then I'll just change stem seals (& retainers since they are cheap)
@mattweck22866 жыл бұрын
Pretty good video just did this with my 4.8L truck. Ended up using .560 lift springs from Brian Tooley Racing!
@614XJ5 жыл бұрын
I'm not sure I can do this myself in my garage.. kinda scared to since it's my daily. How much would I be looking to spend on the valve train to upgrade it and make it reliable, handle power later on down the road? What else should I upgrade while his is going on the rocker arms I heard but anything else? My car has 147k miles 98 C5.
@PABLORL19895 жыл бұрын
dont be intimidated man. im doing this for the first time. basic ratchet set and a few extensions. i am using a compressor to hold the valve up at 60psi. (pancake air compressor). it just takes a few repetitions to get a good rythm going.
@joemedeiros72895 жыл бұрын
Gre
@damyrmonjaras77563 жыл бұрын
Can you crank the engine back up as is even tho the piston was on top dead center