Creality K1 Max Detailed Review | Big, Fast, AI | The Perfect 3D Printer?

The Creality K1 Max is one of a new breed of fully enclosed, super fast 3D printers. It comes pretty much ready assembled and requires almost no setup. It has WiFi, Ethernet and a webcam built in which makes starting and monitoring prints extremely easy.
It uses its webcam and a LIDAR sensor for a number of AI features intended to improve print quality and reduce failed prints.
I’ll run through its features and thoroughly test all of Creality marketing claims to see if this is the right 3D printer for you.
If you want to skip forward or back at any time in this video, please use the chapter markers KZbin creates from the timestamps down below and in the pinned comment.
--------
Affiliate links:
Creality K1 Max: shrsl.com/4ff83
Filament:
Creality Hyper PLA: geni.us/Fj6Nd3
eSun PLA+: geni.us/kkXmkl
eSun ABS+: geni.us/Fj6Nd3
Written article: thetechnologyman.com
--------
You can find most of the recent tech I've reviewed recently all in one place on my Amazon page. I also have a list some of my recommended tech and my current camera equipment for filming:
UK: amazon.co.uk/shop/thetechnolog...
US: amazon.com/shop/thetechnologyman
--------
Music in video from:
Epidemic Sound:
www.epidemicsound.com/referra... (FREE 30 day trial with this link)
--------
Timestamps:
0:00 Intro
0:35 Overview Unboxing, assembly, initial setup
1:30 Self inspection, input shaping, bed levelling, automatic z-offset
2:20 Printer specs
4:02 LCD interface overview
4:38 Camera, LIDAR sensor, PEI build plates, hotend overview
5:18 Loading filament
6:06 Sending first print - 16 minute 3DBenchy via LCD screen
6:55 Removing print from bed
7:08 Performance Using Creality Slicer, overview
7:58 Slicing 3DBenchy in Creality Slicer - comparison to 16 minute Benchy
8:14 Slicing & Sending large PLA model, how to send over network
9:07 Monitoring prints via webcam, timelapses
10:10 Slicing models with other slicers - upload via web interface
10:35 Monitoring prints away from home with Creality Print app - setup
11:23 Activating free 1 year subscription to Creality Print Premium, mini review of Premium
11:59 Cable management box result (PLA)
12:27 Testing AI features
14:02 Printer noise measurements - hear for yourself
15:28 Changing filament
16:08 Fast printer with other filament (not Creality's Hyper PLA designed for high speed printing)
16:18 Foldable crate Grey Hyper PLA - test whole bed first layer, flow rate discussion
16:45 Foldable crate Pink eSun Matte PLA
17:07 Lid off for PLA, print to store glass lid for PLA prints
17:29 Printer drawer PLA
17:45 Printing PETG, glue stick (or equivalent discussion), textured sheet
18:35 TPU (Flex) - nozzle clog - clearing
19:24 Nozzle change
19:45 Attempting to improved bed level
20:53 First layer further discussion, flow rate
21:01 Printing ABS (enclosure printing)
21:38 Printing Polycarbonate
22:01 Testing AC bed heating speed, thermal imaging measurements of bed (compared to Prusa MK3S+
22:39 Measuring time to start print
23:01 Upgrading firmware, root access, installing more advanced Fluidd web interface
23:54 Accessing Fluidd web interface
24:03 Printing directly from Orcaslicer
24:15 KAMP: Klipper Adaptive Meshing Purging brief discussion
24:29 Conclusions
--------
Creality Print Premium offer: www.crealitycloud.com/post-de...
Prusa material guide: help.prusa3d.com/materials
Rooting: github.com/CrealityOfficial/K...
Orcaslicer profiles: cults3d.com/en/3d-model/tool/...
KAMP: github.com/Guilouz/Creality-K...
Cable management box: www.printables.com/model/1467... Springy ghost: www.printables.com/model/6013...
Foldable crate: www.printables.com/model/5132...
Top clips bowden: www.printables.com/model/5337...
K1 Max bottom drawer: www.printables.com/model/5500...
K1 Max lid mount: www.printables.com/model/5539...
iPhone 15 Pro Max SSD Mount (my own design): www.printables.com/model/6214...
--------
#crealityk1max #crealityk1max #3dprinting

[@arnifa]

Excellent video! Love my K1 Max. The speed + build volume is the best part.

[@TheTechnologyMan]

Thanks! Yes I agree for speed and build volume it’s a very attractive proposition!

[@Turtle3379]

Thanks for another great review, Gidon. I just got one of the K1 Max printers for Black Friday! I’m excited to see what it’s capable of! I appreciate the honest review for everything and I am researching ways to correct anything I can to make my experience with it a perfect as possible. Keep making these great videos!

[@TheTechnologyMan]

Thank you - glad you liked the video! Enjoy your new printer. Got me out of a plumbing problem just this afternoon!

[@zchan1120]

how much was it?

[@KannelmaeKaspar]

You did a really good job on this review. Really informative and well put together.

[@TheTechnologyMan]

Many thanks!!

[@jeffsabel9363]

I really enjoyed your review. I was not familiar with your channel but found this enlightening and very pleasant. Thank you! I subscribed.

[@TheTechnologyMan]

Many thanks much appreciated - and very glad the video helped!

[@eonise]

Great review, to the point and informative, thanks. Would welcome any follow-up videos on further tips, tweaks and improvements for the K1 Max.

[@TheTechnologyMan]

Thank you! Great suggestion - I will do my best!

[@antoniomromo]

Thank you for the detailed review. I purchased one along with a micro Swiss hot end replacement. Other reviews say this helps with nozel issues and they are easier to swap.

[@TheTechnologyMan]

Enjoy - my original hot end still going strong!

[@qwertyzxaszc6323]

I have been amazed at how much I love this machine, I have been printing with this thing nonstop with no issues whatsoever. ASA, TPO, everything flawlessly out of the box.

[@TheTechnologyMan]

That’s great you’ve had no problems - mine’s being mainly well behaved 😁.

[@CharltonSupporter]

I upgraded to the K1Max after my initial Creality Ender 5 Pro. I had two months trouble free printing then bang. On a largish print something failed and the nozzle started hitting the surface of the print. I contacted Creality support and after some emails bouncing around finaly got to chat with a guy on Messenger. With the information I provided they concluded the main board had failed. I am awaiting delivery of a replacement. After removing the base plate I noticed that the fan attached to the base plate had been hitting the cooling fins on the heat sink for the motor control chips. I will need to sort out a fix for this before fitting the replacement board. Thanks for a great review video.👍

[@TheTechnologyMan]

I hope you're up and running again soon! I've taken the bottom off a few times and not checked the clearance between the fan and heat sink - but will next time! I have heard this mentioned on the Facebook groups - so maybe check for a solution there if Creality can't help.

[@CharltonSupporter]

Creality advised leaving a screw out. Which I thought was a bit off. I think cutting a piece off of the fin to give clearance may be am option. There is one heatsink across all chips. Maybe individual heatsinks would be better. I will look into that also.

[@TheTechnologyMan]

​@@CharltonSupporter Very strange oversight from Creality!

[@chrisnagy]

I purchased the K1 Max today, so hopefully I've made the right decision. This is mainly to say thanks for the code as it help a lot towards the purchase and final decision.

[@TheTechnologyMan]

Glad I could help!

[@Whaley96]

Do you like it?

[@kehindehassan8668]

Good to know someone just bought one :). Mine is still unboxed and thinking of sending back after a week..the main reason is a lot of reviews point to the cables at the top and their challenges with the printer, the flimsy door latch and non-laminate glass design and the bed level issues. I do like this review though. Pls share your initial experiemces

[@simonchetwynd]

Thank you for taking the time to do this video. You may now pause for breath! 😂. Highly likely I’ll get this printer as I have a project where I need to make some big parts (even with them segmented) so really need the size and speed. Great review, goes through pluses and minuses with lots of info and summary at the end. The way reviews should be done.👍

[@TheTechnologyMan]

Many thanks glad it helped you out!

[@DavidBealeakaFKD]

I've been watching more than a few K1 Max reviews as I'm seriously thinking of getting one. Your video is among the best, well detailed, to the point and useful. Thank You.

[@TheTechnologyMan]

Thank you - very glad it was helpful!

[@DavidBealeakaFKD]

@@TheTechnologyMan ... of course now I have to decide to get a K1 now, or wait until the K2's are shipped, then wait a few months for the initial production run is sold and buy a K2 next year when it's bugs have been worked out. ... Hmmm, a test of my tolerance for delayed gratification.

[@GerardoNQ]

If you have the budget, I highly recommend purchasing a Bambulab P1S or P1P printer, as they are much better options. I own a K1 Max, and I find it quite challenging to manipulate, with issues regarding bed leveling. I do not recommend it.

[@DavidBealeakaFKD]

@@GerardoNQ Was really tempted by the Bambu Lab products. Two concerns, one is they are not quite large enough and two some of the reviews of how their software works concerns me. No fan of cloud based connections - live in northern Canada with satellite internet connections, cloud work is a pain - especially on cloudy days (real clouds interferes with e-cloud connections). I used Tinkercad for example on the cloud and sometimes I'll have to wait and go get a coffee while it assembles the model. If they come out with a max - maybe I'll get over my security concerns, and if I can download the software and work off line that would be an OK work around.

[@BENZINACVW]

Nice Job Man ! Thanks for Info !!!

[@TheTechnologyMan]

No problem glad I could help!

[@TinkerTime]

By the way great video. Liked and subscribed. Cheers🎉

[@TheTechnologyMan]

Thanks!

[@richardwillcox4097]

excellent content I'm considering the K1max as my next printer. My previous experience with Creality wasn't good (ender5S1 with sonic pad) I'm currently using an Elegoo 4 pro with good results.

[@TheTechnologyMan]

Thanks! I think Creality have done a good job with the K1 Max - I'm looking forward to the next firmware update that should fix a few issues still remaining.

[@the-matrix-has-you]

​@@TheTechnologyManwhat are those issues? I am also considering buying K1 Max especially for its AI Lidar Sensor auto bed leveling capability

[@lindeleasley]

I've had mine for about a week, and so far, it's been pretty good. I'm used to working with Cura, so I'm taking my time learning Creality Print. I haven't had the issues that you apparently did with the phone app. Mine seems to work fine with both the K1 Max and my CR-10 Smart Pro. I will say that the speed of the K1 is very impressive. I scaled up the benchy to 300%, and it took 4 hours on the K1, where it took nearly 4 times as long on the CR-10.

[@TheTechnologyMan]

Great to hear!

[@airheadbit1984]

The most thorough review I've found, thank you. I jumped on a K1 during the recent past 'Black Friday' discounts, under $400, I figured the K1 Max and K1 where the same except build area, nope. Seems no one had mentioned the A/C hotbed on the Max, that is not a small difference, that and the 1,000 watt power supply for the Max where the K1 has a 350 watt supply. It's taken me over the 15 day return period from Creality so I'm stuck with the K1, I also found out all the nozzles (.2~.8) are for the Max, there is no nozzle profiles for the K1 or K1C besides 0.4.

[@TheTechnologyMan]

Thanks glad video helped but sorry you've had trouble with your K1.

[@egeislekel7403]

Great video! Thank you! Are there any improvements on Lidar with the latest updates?

[@TheTechnologyMan]

Thanks! I have the latest firmware but still don't feel LIDAR offers any real benefits.

[@egeislekel7403]

@@TheTechnologyMan I have Neptune 4 Max, the bed leveling and other calibrations take forever. I'm planning to buy K1 Max but I'm still not sure about it. I'm between X1C and K1Max.

[@dyops]

Thanks for the review. I plan to buy my 1st printer next month and it's down to either the K1 Max or P1S Combo. Both are similar priced but the K1 can be cheaper with discounts. Bambu doesn't usually offer discounts. I have reasons to get both but I'm leaning towards the P1S because of ease of use, quality prints, and lots of possibilities with the AMS.

[@TheTechnologyMan]

It's a tough one. I'm hoping to test a Bambu Labs printer soon. The extra size of the K1 Max is the big draw - if you don't need that then I'd definitely be choosing between the K1 and one of P1S or P1P depending on budget.

[@amil89]

If they didn't use proprietary nozzles and force their cloud it would be a no-brainer for me to choose bambu. Since they don't I went with K1. Got a 15 pack of steel nozzles for the price of one bamboo nozzle. Printing on my local network and none of my intellectual property is being sent to China lol

[@nforc3r87]

@@amil89 How do you like it? I got P1S 2.5 months ago. It had a shorted mainboard at delivery. I been dealing with poor bambu sport since Thanksgiving. I am on the verge of returning this and get something else. I replaced the board. But now it wouldnt connect to the wifi. Giving me all type of errors. Camera not working and I accidentally clipped the ribon cable while trying to fix the clog and it cost $20 to fix it LOL. I will return in and get either A1 AMS or thinking on K1.

[@3D_Printing]

Excellent video review

[@TheTechnologyMan]

Thank you! Cheers!

[@jakiehan.]

great review, i want to get one K1 max

[@TheTechnologyMan]

Thanks - let me know how you find it if you get one!

[@timswift5197]

Good review., thank you. I bought one just over a week ago and have been generally pleased with the results so far. Except when I printed the Benchy test file that is loaded on the m/c I noticed that the embossed text on the underside was barely readable. I have printed the Benchy on other m/c's and the text is usually distinct. I also went on to print a file of my own which has a fairly shallow 'engraving' on the bottom surface and it did not show up at all. I'm wondering whether this is something I'm doing wrong or whether others have had similar issues. Keep up the good work.

[@TheTechnologyMan]

Yes by default the first layer is a little too squished on mine too - even with the very latest firmware. You can adjust the z-offset as I demonstrate in the video.

[@nerferx]

I had a K1 for a week, and sent it back, it just had so many issues, 1st layer was never spot on, adheasion issues too. Paid the extra for the Bambu Labs P1S (without the AMS) and it is worth every extra penny. I am so happy with it I am investing in more to replace my aging Flashforge fleet.

[@TheTechnologyMan]

Must test the P1S! But I do like the extra build volume of the K1 Max.

[@lLoneRoninl]

Sounds like user error on that one lmao

[@Brise215]

​@@lLoneRoninlits not user error. K1 max is known for more issues. I am amazed with bambulab too but i recommend the build volume. The some centimetres are so much helping something bigger. Hope bambu lab will bring aut a max version.

[@lucasgarelli9516]

There was an issue with the last firmware updated few weeks ago in the first layers. Downgrading it to the last available in the web fixed it. No more adhesion problems again.

[@lLoneRoninl]

@@Brise215 definitely user error. I haven’t had any issues at all. You Bambu guys just salty. Pathetic to have to make up stories. Stay salty.

[@Waltuh7862]

I have yet to see my K1 Max do the zig zag lines for flow calibration, how can I make it do this/properly calibrate the flow in general?

[@TheTechnologyMan]

Even with the latest firmware I don't find the flow calibration reliable - but you need to turn it on under settings | camera | ai settings IIRC.

[@antennasbc]

Ya this is a great review. Thanks!

[@TheTechnologyMan]

Glad it was helpful!

[@tankumaat]

Very satisfied with print speed and quality with K1, but it seems to leave dents into patterned hotplate, especially in tip cleaning area, noticed this after about 5 prints only. It is fine with original hotplate.

[@TheTechnologyMan]

I take it you did a levelling routine with the new plate? Are you on the latest firmware just released?

[@TheTechnologyMan]

Are you considering this printer or if you already own one what do you think of it? Please let me know down below! Purchase K1 Max directly from Creality Store and get $50 or £50 off using my code TTM50 (note this a tracking link for Creality - I don't get any commision): bit.ly/3PmXSRM Timestamps: 0:00 *Intro* 0:35 *Overview* Unboxing, assembly, initial setup 1:30 Self inspection, input shaping, bed levelling, automatic z-offset 2:20 Printer specs 4:02 LCD interface overview 4:38 Camera, LIDAR sensor, PEI build plates, hotend overview 5:18 Loading filament 6:06 Sending first print - 16 minute 3DBenchy via LCD screen 6:55 Removing print from bed 7:08 *Performance* Using Creality Slicer, overview 7:58 Slicing 3DBenchy in Creality Slicer - comparison to 16 minute Benchy 8:14 Slicing & Sending large PLA model, how to send over network 9:07 Monitoring prints via webcam, timelapses 10:10 Slicing models with other slicers - upload via web interface 10:35 Monitoring prints away from home with Creality Print app - setup 11:23 Activating free 1 year subscription to Creality Print Premium, mini review of Premium 11:59 Cable management box result (PLA) 12:27 Testing AI features 14:02 Printer noise measurements - hear for yourself 15:28 Changing filament 16:08 Fast printer with other filament (not Creality's Hyper PLA designed for high speed printing) 16:18 Foldable crate Grey Hyper PLA - test whole bed first layer, flow rate discussion 16:45 Foldable crate Pink eSun Matte PLA 17:07 Lid off for PLA, print to store glass lid for PLA prints 17:29 Printer drawer PLA 17:45 Printing PETG, glue stick (or equivalent discussion), textured sheet 18:35 TPU (Flex) - nozzle clog - clearing 19:24 Nozzle change 19:45 Attempting to improved bed level 20:53 First layer further discussion, flow rate 21:01 Printing ABS (enclosure printing) 21:38 Printing Polycarbonate 22:01 Testing AC bed heating speed, thermal imaging measurements of bed (compared to Prusa MK3S+ 22:39 Measuring time to start print 23:01 Upgrading firmware, root access, installing more advanced Fluidd web interface 23:54 Accessing Fluidd web interface 24:03 Printing directly from Orcaslicer 24:15 KAMP: Klipper Adaptive Meshing Purging brief discussion 24:29 *Conclusions*

[@jamesharris9894]

was but seen all the issue figured I'd give it while see if they can fix it but assuming someone will make a larger printer before they fix k1 series

[@user-gh8tw1sv7o]

doesnt work i need for EU store

[@joelmichels5564]

Thanks for the honest review, i own a k1 Max, prints very good no issues so far. Dislike however the claims that the printer uses IA, and Creality OS which is actually Klipper which to be honest is perfekt. however for super tricky and refined prints I use my MK3S, it is super slow, but the prints are a tick better than on the K1, maybe this might be improved with better slicer settings? All in all I am quite happy

[@TheTechnologyMan]

Yes I get better quality with my Prusa's but so much slower than the K1 Max and the Flsun SR.

[@amil89]

Before you do ANYTHING. Check your FRAME!!! I had a terribly twisted frame on my K1 Max and it made all my square prints into a rhombus shape. My lid was not even close to fitting on top. This was due to mishandling in shipping, but they will replace it for you if you provide pics to Creality support. Cant wait for my replacement, my test prints were 4x faster than my other printers despite the frame issue. I also did my 16m benchy in eSun PLA+, came out better than my 1hr benchy on my Ender 3!

[@TheTechnologyMan]

Hope you get sorted - they've just shipped updated firmware that is meant to fix a few of the issues I had. Will test it out shortly.

[@amil89]

@@TheTechnologyMan new printer arrived with a perfectly square frame. Phew... Unfortunately some error happened during bed leveling in the nozzle completely stabbed into the center of the build plate. I'm pretty pissed that my build plate is marred after a couple hours of use. I sell phone cases that require a perfect bottom layer. I sent them an email about this but have not heard anything back. Finding out that I actually have to calibrate this machine to print well, when I thought it would be a plug and play printer. I don't mind doing that but beginners would never know to do so

[@celik_murat]

wonderfullY content thanks mister Gidon

[@TheTechnologyMan]

Thank you - glad you liked it!

[@BanTauVn]

What type of plastic do you use and what brand does it come from?

[@TheTechnologyMan]

I've added links to the filament I've used in the video description. I tend to use eSun bought from Amazon. But also used Creality's Hyper PLA in this video - also available from Amazon.

[@exaltvideo]

This printer or the prusa mk4? I'm looking for speed and quality, not really worried about size

[@TheTechnologyMan]

Sorry not tested the MK4, but I will say I have the MK3S+ and Prusa Mini and choose the K1 Max over them all the time because of the speed and convenience. Plus having an enclosed printer lets you print way more materials much more easily. Personally if I was picking a printer right now between something like this or the K1 and a Bambu Labs printer.

[@NickBR57]

Get a Bambu then

[@TinkerTime]

Would it be possible to SSH into mainsail versus fluid?

[@TheTechnologyMan]

You can use Mainsail or Fluidd 😊.

[@tuxflyer]

@@TheTechnologyMan After you have enabled root. Without that it's not possible.

[@TheTechnologyMan]

​@@tuxflyerYes that's correct - I hopefully explain that in the video.

[@EnergySeeker]

I have the k1 max but my LiDAR don’t do that red light what am I missing to do ?

[@TheTechnologyMan]

You have to turn on the feature as I describe in video. It doesn't do a lot currently so I probably wouldn't bother with it!

[@EnergySeeker]

@@TheTechnologyMan it stop after scanning and give an error msg to end printing or resume

[@PapLab]

Can you share the top lid holder file? Thanks!

[@TheTechnologyMan]

Sorry added it now to the description!

[@gabeplays9441]

How is it compared to the X1?

[@TheTechnologyMan]

I’ve not yet tested any of the Bambu printers. And they don’t yet have one with the K1 Max build volume.

[@mjethier]

I wish it was. I have bought 5 of this model, over 10 of them in general. 1 has been decent from the start as far as K1 Max units. Not a fanboy of anything but what works as I expect it to. My bambu units I have work just about flawlessly from the get-go. I have no problem showing pictures and videos to justify my statement. I think it's a gorgeous printer. But the amount of shipping damage coupled with warped beds and consistent failures has me a little chapped.

[@TheTechnologyMan]

Disappointing - I hope you managed to get a replacement / refund.

[@SchutzeMania]

i just upgraded from a monoprice maker select. the max is like a spaceship compared to my gremlin XD

[@TheTechnologyMan]

Great!

[@RaminOhebshalom]

Thank you

[@TheTechnologyMan]

You're welcome thanks for leaving a comment!

[@BigRedViking89]

Great video! I could not help but ask, have you had any experience with Creality's Hyper PLA (Black)? I recently purchased my K1 max and have had great results with the Hyper PLA (White). I carried out many test of a model I'm printing for a work piece and I was asked to print it in black. I do not know why but I have had nothing but issues with black Hyper PLA. The model constantly releases from the bed and appears to shrink or curl. I have tried glue on the bed, I've tried higher temps on both the nozzle and the bed I've also turned off cooling and still can not get the thing to print. Any ideas or have you experienced anything like this before?

[@TheTechnologyMan]

Thanks! Sorry I've only got Hyper PLA in white and grey. Have you gone back to try printing white Hyper PLA - perhaps the test model speed Benchy? Otherwise perhaps try thoroughly cleaning the sheet with a bit of washing up liquid and a non-scratch scouring pad and then dry it thoroughly. Also run the bed levelling routine again. Has the PLA got wet at - perhaps try drying it out? It's unlikely to me it's anything specifically to do with it being black PLA.

[@gregmurray449]

I found a setting in settings, experimental and put a tick in the box for enable Gcode offset and play with it in small increments mine is 0.03 weird right hahaha lol

[@Waltkat]

Ordered one of these, can't wait to get it. All of my other printers are smaller and unenclosed so this will be great for ABS, ASA and Nylon. The noise doesn't bother me because I've worked in industrial manufacturing facilities so I'm used to it. know someone with three of these in a print farm and he likes them so much that he just bought four more.

[@TheTechnologyMan]

I hope you like it - let us know when your thoughts when it arrives!

[@amil89]

be sure to check that your frame is square. Lid fitting is easiest way to check." Mine was horribly twisted from being dropped in shipping. Even the screws holding the bed down were bent badly (one was completely removed and loose in the printer)

[@_Feanor_.]

The only critique I have with an otherwise amazingly detailed video with so much information is that never mentioning the price. At 30 seconds it says "to see if this is the right 3D printer for you". Then 26 minutes pass until the price is mentioned in the form of links in the description. Yes, prices change with time or depending on region and all that. Would still be nice to know what it cost at that time to get some idea. Since the price is a key determinant for many people.

[@TheTechnologyMan]

Thanks for the suggestion!

[@workingTchr]

Creality copies Bambu (good) but the head crashes into the bed?! That's EXACTLY what happened with the Ender 3 I bought (and returned) right before the P1P became available.

[@TheTechnologyMan]

Hopefully now been fixed with the latest firmware! I've not had the issue for a while.

[@geoffreym2769]

I bought this as my first 3D printer 10 hours ago, so far so good, worked perfectly out of the box, My 13 year old son found a free website to print things from, so it's now doing an overnight print 8 hours

[@TheTechnologyMan]

It's a great hobby to do with the children!

[@StuckOnAFireHydrant]

Wait so you don't have ringing on your prints? Man what the neck is going on with my k1

[@TheTechnologyMan]

Is the printer on a stable table? Make sure you run the Self Check | Input Shaping again if it's been moved. Then run the various calibration tests in Creality Print. You won't eliminate ringing and some VFA at high speeds but especially for functional prints, the quality is pretty good.

[@briankale5977]

Well, being a Creality paper weight, it's probably the garbage QA showing itself. Belts losing tension, extruder feed rate not uniform etc

[@tabhinton6678]

Bought one. Printed a 100 mm part and it measures 99mm's. The holes wouldn't fit with the mating part. Finally got an email back from Creality. There is no method of calibrating this machine. So if you are printing a vase or a character it's great. If you need to print parts that have to fit together buy a different brand of printer

[@TheTechnologyMan]

If you get consistent inaccuracies you could apply a small scale factor to your prints. Also where you print on the bed can have an impact - so might also be worth checking. I only print functional parts on my K1 Max and find it pretty good.

[@nickg1688]

Hi, where Are the Linked Print files?

[@TheTechnologyMan]

They're in the description - towards the bottom?

[@nickg1688]

@@TheTechnologyManOh sry, did Not das them. Liked the Video

[@TheTechnologyMan]

@@nickg1688 No my fault - I went to double check after I replied to you and they'd gone! I must have cut and pasted them to my written article rather than copy and pasting 🤦‍♂! Thanks for letting me know.

[@ashtonwoodturnings225]

Great review but way to expensive for me

[@TheTechnologyMan]

I'd expect some big discounts in the coming months! 🤞

[@lucasgarelli9516]

in Cafago is usually 200€ less

[@amil89]

$680 with the current sale and discount code. that is very cheap for a 600mm/s CoreXY machine, with 300mm³ build volume If you want a cheap machine you can get a Ender3 for $130

[@olivermj69]

I don't see why one would go for this and not the BambuLab P1P, nevertheless thanks for the review

[@TheTechnologyMan]

I guess for the build volume mainly.

[@TheGroundedCoffee]

Personal ownership of data comes to mind....

[@amil89]

- Local Printing (no sending my intellectual property to the CCP) - 1.6X the build volume - Faster - Non-Proprietary parts (can get any volcano nozzle) - Open Source - Upgradeable If Bambu used non-proprietary parts and had an option to print locally I would have gotten the P1S. They are trying to be Apple and lock their customers into only buying parts from them. I refuse to play along with that kind of behaviour.

[@user-nk3sn5dv8d]

Excellent presentation skills, would like you to speak a little slower, buy well done.

[@TheTechnologyMan]

Try reducing the playback speed to 0.75x - KZbin does a good job on this. And you can enable captions - I have full transcripts for every video. Hope that helps.

[@naturfagstoff]

Outstanding review.

[@TheTechnologyMan]

Thank you - very glad you liked it!

[@ichwillzaster]

its a X1 carbon clone... times have changed... now Creality isn't the company being copied, now its the company copying other designs

[@TheTechnologyMan]

Definitely! To be fair the Ender-3 was a MK3 clone - but it did get a lot of people into 3D printing which can only be a good thing! I'm personally very grateful that Bambu Labs came up with the X1 Carbon and their new mini is even more disruptive.

[@TigraZ]

k1 its better =D

[@TheTechnologyMan]

😊

[@littledev556]

Bri'ish

[@TheTechnologyMan]

?

[@briankale5977]

Standard Creality, missing the mark of the people they were trying to copy. Oh well. But don't get suckered into the low price if youre a newbie, you'll be tinkering and "modding it to work better" more than printing with it. 😂

[@TheTechnologyMan]

I’m not sure the K1 Max needs modding but they do need to work on firmware. And at same stage take advantage of the LIDAR sensor.

[@tombo7719]

If it’s from Creality, sadly no.

[@TheTechnologyMan]

Fair enough!

[@amil89]

so you'd rather send your intelectual property to the Chinese Communist Party? At least creality lets you use their printer on your local network only if you want. Bambu FORCES you to link to their 'cloud' If you are just printing other people's models, then whatever. I am NOT sending my prototypes to China to be copied and mass produced. I have a business to run. This is not a toy for me

[@kurtlazarus5975]

NO ONE BUY this it's terrible LIDAR is fake and doesn't do anything first layer is shit I took mine back in the first 3 hours of owning one.

[@TheTechnologyMan]

Even without Lidar first layer should be ok.