Creative Ideas From Used PC Power Supply

[@anak1000bapak]

Mantap 👍👍👍 Catatan saja bang resistor 10ohm Sbg dummy load nya jangan nempel ke PVCnya hanya menggunakan alas tape karena panasnya tinggi bahaya bisa mlonyot /meleleh boxnya

[@creatividea]

makasih

[@raskahefendy1637]

atau sebaiknya tidak usah pakai dummy load, tapi dgn syarat tombol powernya pakai saklar on off, jgn pakai push on button.

[@EdiKun157]

​@@raskahefendy1637Itu fungsinya untuk apa ya om?

[@ramazantosun51]

Good work, good luck. Did you add the stone resistor to remove short circuit protection? If I'm not mistaken, you started with the red cable, that is, 5 volts, and the black cables. thanks.

[@charlesantoney1769]

I loved the step-by-step assembling technique you used.

[@w13rdguy]

There are many different ways to do things, but this way is very practical, and from easily available resources.👍

[@kiwiskiz]

Very neat project! From an electrician - You really should make a better earth connection on the supply side, super important with switch-mode power supplies.

[@GasketManzrevenge]

As an automotive diagnostician and electronics project hobbyist, I concur. Poor grounding can create a myriad of faults.

[@edsonf304]

Ótimo trabalho, Muito bom mesmo. Com um design agradável. Funções bem definidas e práticas. Parabéns. Tudo de bom para você e os seus. E aguardando mais trabalhos, para nos inspirar e ajudar nesta "arte" que tanto gostamos. 👏👍

[@creatividea]

obrigada🙏🙏🙏

[@danieldani2386]

​@@creatividea Romania?

[@cherlsoonyim6362]

참 좋습니다.

[@dinfahmi542]

MANTAP,,,kalau sambung buat port usb a, dan type c,lagi padu ni

[@creatividea]

ambil dari jalur output 5V yang kabel warna merah, kalo mau fast charging tambahin modul fastcharging sesuai spek HP

[@jobspeedmms]

ide yang sangat bagus dan bermanfaat kawan..

[@JefryAnsElt]

Trmksh ini sangat berguna

[@triwibowo8500]

Haii jefry, aku sering liat youtube mu.

[@JefryAnsElt]

@@triwibowo8500 trmksh pk

[@creatividea]

Terima kasih kembali

[@klep_on]

bagus, cocok untuk repair HP/Perangkat Elektronika

[@samsulfals-lj1mm]

Sangat bermanfaat.. jadi tambah ilmu. Semangat berkreatif. 👍

[@wasilyok090662]

Классная универсальная приспособа получилась !!! 👍👍👍

[@theromeog]

That ground strap connected to the plastic stand off and pvc case.... Work of art ! ! ! ! ! 😷

[@timh0r]

wanna talk about the 12V rail transformed into car ligther plug and then back to 5V while there is a 5V rail available already on this ? Or about how dangerous those old shitty PSU are ? Or the bad ground soldering on the right converter ? I also hope that fuse is 12V 10A and not 240V...

[@samsien9105]

@@timh0r the most Asian countries used 240 v 50w AC transformer , private used no matter their own risk , I done ugly more than that ,but for my own used just 1 battery I can cook food and light all night lone while I'm gone fishing .

[@BENGLASBERKAHCHANNEL]

Kreatifitas yang tinggi perlu orang yang profesional untuk seperti ini....lanjutkan kawanku....salam dari saya ngopi yuk roomku

[@creatividea]

makasih kawan

[@agusm20856]

Patut ditiru buat kebutuhan rumahan.. DIY project

[@Cucungah]

Tetlalu syulit

[@FRESHFOODSandEATING]

Very creative stuff. Thanks for sharing

[@hugolloyd31]

Increíble maestro. Ud. es todo un genio. Saludos desde la ciudad de Iquique Chile.

[@kurtwm2010]

Great built and perfect for a weekend project.

[@factrefute4427]

Excellent project, thank you, it is worth every second OF WATCHING.

[@Pjierke]

Nice, I got several old pc, I see a second live for the power supply, thank you! One question how did you make that nice lay out is it a sticker, how did you made it. Keep up the good work!!

[@ricardoflores5422]

Que belleza es la gente como tu que recicla y de cosas que se tiran hacen un lujo.. ojalá exportes mucho, vendas muchos y te apoyen mucho más... Yo lo unico hasta donde llego a desarmar la fuente, después la vista no me da para más jaja.... Genial !! Disfrutando su sabiduria!!

[@aryokesuma4071]

Tutorial yang sangat bermanfaat 👍

[@creatividea]

Terima kasih

[@CARLOS_484]

PARABÉNS PELA SUA CAPACIDADE E CRIATIVIDADE ABRAÇOS. SABE. TUDO.👏👏👏👏👏👏👏👏

[@АртурАушев-л5ь]

Отличное видео, отличная работа!!!!! Почему этот мастер не показывает себя? С удовольствием бы с ним пообщался. Я тоже занимаюсь изготовлением электронных поделок. Жаль, что не говорю по английски. Автору видео респект!!!!!!!!!

[@nurtoolsnurtools3562]

Похоже, что автор пакистанец, поэтому он тоже вряд ли по-английски говорит

[@АртурАушев-л5ь]

@@nurtoolsnurtools3562 Не важно кто он по национальности, он творческий человек, я таких людей уважаю. А вот общаться, к сожалению, умею только на русском языке.

[@viktorka2111]

Делал такую штуку. Только ампер-вольтметр запитывал от ЗУ телефона и пожадничал на светодиодный тестер. Жаль, что фото не могу разместить. Корпус БТХ остался родной.

[@mustaphabenali4896]

Really good jobWith a nice design👌👌👌👌👌👌👍👍👍👍👍👍

[@pcmacd]

In _eighth grade_ electronics shop, they taught us that one NEVER depends upon the solder for a joint. You MUST have solid MECHANICAL CONNECTION before you solder it. Don't feel bad as every soldering video I've seen on youtube is exactly like this - INCORRECT.

[@artisanwest9730]

You are correct. I was going to mention this until I found your comment. I'm a retired BSEE and once had NASA space flight certification for soldering.

[@pierrec1590]

Hint: Take advantage of the existing fixed 3V, 5V and 12V by putting banana jacks for those as well. You don't always need variable voltages, but you will always need 3,5, or 12V For example you can power a microprocessor with 5 volts, and then use a variable voltage to test ADC inputs response.

[@itsmeadude460]

@Sheila Walker Just out of curiosity: how would you use those? Are they somehow provided via the ATX-plug?

[@itsmeadude460]

@Sheila Walker I was actually curious how he could use "...the voltage and current sense of the power supply..." by just using the cables going to the ATX-plug... Agreed that some things I would have done differently, like labelling a 12V car-outlet socket as 5V, because you intend to plug a USB-converter into it or GND & housing... Also you can get some nice standard voltage values by e.g. using -12V and +12v -> 24V. I like his idea of hooking up an adjustable DC-DC converter. All in all an old PC switching PSU does not really deliver "crude and un-monitored" electricity though - maybe it's a bit diluted at the output of the adjustable DC-DC converter, but for standard values like 3.3V, 5V, 12V and 24V I'd go for the clean PSU output. Cool idea with the LED test - lots to learn there ;)

[@Николай-с7ю9р]

@@itsmeadude460 😭э

[@markpeterson5479]

By cutting the wires off of the connectors you'd have the 3, 5, and 12 volts out. Group them in parallel by color and feed them to the rest of the circuitry, You wouldn't even have to open the computer power supply - just use it as is.

[@kurtwm2010]

@@markpeterson5479 use it as is... then it wouldn't fit into the new cage.

[@adehidayat1783]

diem diem' bae...metode secepat kilat wussshhh..untuk para suhu wusshhh

[@karnosaptoto]

Mantap sekali Kreasinya, bisa buat Alat Tester Voltage, Lampu LED dan Charger.

[@juancarlossanchez118]

Impresionante trabajo, preciosa fuente, congrats!!!

[@diezelle57]

Bravo pour votre travail. Pouvez-vous me dire quel est cet instrument (jaune) à dessouder (enlever la soudure) ? Bravo for your work. Can you tell me what this (yellow) desoldering (removing solder) instrument is?

[@samoezain.alghofur]

mantap Hasilnya suhu 👍👌🙏

[@muhammadiftikhar5856]

Wonderful Sir excellent fitting all work is completely professional.

[@VODYANOY2022]

Классно все получилось , молодец автор !

[@thomasbrosset7794]

Hi, can you tell me where you had your PVC sheet printed on your front panel with the different button locations on it Thanks to you

[@martinromeo1006]

Amazing my well done 👏 beautiful job 👏 👍 very nice 👍

[@abdulwahid8579]

Very good information and knowledge able video 🙂

[@SC.243k]

Very professional work, Thanks my friend ♥️♥️♥️♥️♥️

[@creatividea]

Thank's 🙏🙏🙏

[@SN2Tutorial]

Mantap tenan rek, pengen buat aku😅

[@juliocesarnatalrn161]

MUITO OBRIGADO, MEU AMIGO, PELAS SUAS IMFORMAÇÕES, TÃO IMPORTANTE...!!!!

[@Dead_inside....]

Проэкт классный👍 Но сода со временем (2-3 года) меняет свои свойства, а так же влияет большая влажность и деталь разсыпается.

[@user-ow3rh3lh7v]

начнем с того- этот пластик цианакрилатом видимо не клеится, от слова СОВСЕМ! сода- попугайство))) по итогу- накерачил саморезов! ))) спрашивается- зачем была нужна сода с цианакрилатом вообще....? ))))

[@olenduschannel7714]

Wow.. good tutorial pembuatan pengacas Handphone

[@Schjoenz]

That's a workbench power supply. What a nice build. I have few PSU lying around but most of them are not working anymore.. Those were replaced from the desktop I repaired. I really want to repair PSU to repurpose them..

[@sniperghillie9235]

Boa Noite com um começo de um bom dia. Fiquei até agora vendo o vídeo dessa fonte que você refez totalmente. Ficou muito legal e gostei bastante da sua ideia de colocar esses componentes eletrônicos e instrumentos de medição. Só faltou o mais importante de todas as coisas que você fez. Foi explicar todos os detalhes de cada modificação. Se você achar que sou digno de sua atenção e respeito por seu canal eu fico feliz em ter retorno de sua parte. Ontem dia 16/09/23 Eu estava tentado fazer uma fonte pra mim de uma fonte de computador e não vi que era 127 volts e entrei com 220v direto. Só vi foi os capacitores estourando.kkkkk me ajuda aí à fazer uma outra pra mim. Obrigado. Fico no aguardo.

[@thewolf3530]

That's really complicated easy for you because you know what are you doing .

[@SerwalterTec]

Gostei de mais do video, adorei parabens deixei o meu LIKE pra fortalecer o canal

[@arduinomaquinas]

Nice, excellent build 😉👍👏👏👏

[@TheSidneypires]

Gostei simples e eficiente. Todos eletrônicos que já vi montando um aparato parecido, teriam que usar uma fonte atx de melhor qualidade, pois a mesma fonte que não serve mais para o pc já foi usada de mais gaste um pouco mais e monte numa de melhor qualidade. Comentem 😎

[@closethehorror]

keren bang ide kreatifnya

[@ivandarioortiz6407]

Felicitaciones... muy ingenioso. Eres admirable.... 👍

[@talentodesajonia9233]

Uno de los mejores Proyectos que haya visto en mi vida, hecho con una Fuente de Computadora, le Felicito al creador de este Proyecto...Saludos desde Paraguay....

[@kjiibrit]

Very impressive! The only things I would add would be a power fuse on the 240V input, and a screen on the fan!

[@creatividea]

Thank you for the input suggestions, as far as I know the fuse is already in the ATX power supply

[@309electronics5]

If you have good eyes and can see the fuse its there its on the board its somewhat easy to see for younger people like me

[@robology_channel]

Luar bisanya kawan ... hasilnya. Teruslah berkarya kawan

[@Tejedorindomito]

Hola que tal! Muchas gracias por tu video. No sé nada de electrónica, pero con estas creatividades me animo a estudiar en forma técnica electrónica. Bendiciones y saludos desde México.

[@martinromeo1006]

Beautiful well done 👏 my friend 👍

[@irbonarsiahaan1052]

Kreatif dan rapi❤

[@HDeltronic]

kreatif banget bang 👍

[@novanmulyana2522]

hanya satu kata HEBAT.... orang asing saja sampai bertanya

[@WalkBaku]

Interesting stuff, need to make one of those myself)👍

[@tuanghamsir2141]

mungkin bagus juga kalau tegangan yang autonya dinaikkan sampai sekitar 200-an volt supaya bisa untuk mengecek led backlight tv

[@creatividea]

Belum pernah coba, tapi kayanya tidak bisa kalo menggunakan skema seperti di video

[@tombarlow6176]

I enjoyed watching you work

[@ZAYYPRO]

mantap bang...sangat kreatif

[@HSCOR22]

Good job 👏 you are the best 🎉

[@dmitriproyekkreatifresmi]

Backsound buat pengantar acara ukm padus uinsa, unair dll 0:27-3:50; 3:50-6:56; 7:01-9:27; 9:27-13:32; 13:32-16:52; 16:55-19:34

[@DrSanaullahkhan98]

Excellent ,all the best and keep it up..

[@jean-michelchevalier6649]

Nice video, thank you. What device do you use to unsolder(potentiometer) if you have any link where to buy it? Many thanks

[@bukanmanusiakarbit2762]

Assalamu'alaikum bang, maaf sbelumnya. Kalau bisa sedikit jelaskan kegunaan setiap komponen tambahan yang abang pakai, sperti resistor dan lainnya. Agar yang awam sperti saya bener2 faham kegunaan dari komponen tambahan trsbut. Terimakasih🙏🙏🙏

[@costacedric8668]

Bonjour, beau boulot!!!! MERCI!!!

[@lisu6060]

In this video, what tool did you use to remove solders so cleanly and quickly from the PCB board in order to remove the potentiometer from the voltage converter?

[@ozcanonal]

I liked this transformation 👏👏👏

[@megaskuns]

Капец. Такого я давно не видел, жесть. Лабораторник подъехал!!!

[@frankrassiga8294]

nice project. Could you please tell me why you inserted a 10 ohms 10 watts between 5v out and Ground? thanks in advance for your reply

[@artisanwest9730]

The 5V output is the primary regulation output so the resistor is providing a minimum load. Some supplies can't regulate down to no load.

[@putriamalia422]

Good work sir, nice. Btw saya sudah servis PSU karena sekring kaca putus seperti meledak didalam. Setelah diganti sih normal bisa dipake dan semua voltase ada. Rencana mau buat benchmark juga, yg pngn sy tanyakan itu sekring meledak karena apa ya ? Kelebihan beban atau gimana

[@sharmaanupoju5322]

😃Wow super skill 👏👏👏👏👏

[@muhammadasghar2627]

GOOD IDEA BRO, MAKE MORE SUPPLIES AND LAUNCH IN MARKET FOR COMMERCIAL USE AS WELL💯.

[@cozzyinternet4706]

nice work! cheers for sharing! also, great idea for a helping hand!! 😀👍

[@crchaniagostar6768]

Ini mah suhuu😊

[@zorolom8910]

Ini baru mantap.. 👍

[@mhammmmagh1465]

beautiful work

[@jeffreyholicky4303]

Well if you wanted to make something that looked like it came out of Russia - good job! Can't wait to see the carry case.

[@retiredjan4714]

Nice build and also the trick with the multi-turn. Just one thing: the 10 Amp as specified for the auto_buck_boost is for the max current of ether (input or output) else the magic smoke will be released.!!

[@jean-francoiscandy6515]

Il faut vraiment être balaise en électronique pour fabriquer un truc pareil bravo et félicitation...

[@antonioaugustosturaro5055]

Ficou legal demais esse projeto! Parabéns!

[@creatividea]

obrigada 🙏🙏🙏

[@izabelmartinsmourao7726]

Mas afinal o que ele criou mesmo? Um multímetro e um relógio foi?

[@veeem3964]

You have to be very careful of those high capacity capacitors as they hold a lot of voltage for a long time . Make sure they are discharged

[@someone-user]

Стоило бы в регулеровке напряжения использовать два последовательно соединенных потенциометра - "грубо" и "точно".

[@frerespirituel.1]

Thank you very much, good luck, important information

[@ajithoneiro]

Good one...tons of information.

[@sergeg1964]

hello I would like to know where I can find the front face of the power supply (screen printing) thank you

[@lan8544]

Мужик ты реально крут отличную вещь сделал уважаю👍👍👍👍👍

[@ramonantelo9370]

Fantastic ! Can you share a video building a similar AC power supply variatior from 100 v to 230 V ?

[@atelogo]

hello sorry a curiosity what is the 10 ohm 10w resistor for?

[@tipsmoolag]

Bisa dipraktekan di rumah nih

[@SerwalterTec]

I liked the video the most, I loved it congratulations I left my LIKE to strengthen the channel

[@jamilahmed1627]

Excellent n super ideas

[@ohchapeau9348]

Lavoro pulito,meticoloso, e molto attento...BRAVISSIMO! Non capisco solo cosa siano e a cosa servono i 2 moduli.. grazie

[@Олег-м8р5к]

Хорошо когда есть идея как использовать старые вещи

[@adicitrapt]

luar biasa... 👍👍👍

[@lejardindeloiseaubleu]

Thanks for the video, your desoldering pump looks really efficient, what model is it?

[@AVSmadiunofficial]

masukk masukk

[@guylechat1124]

Quel talent 🙏🏻🌹👋.

[@SCARMAXFIB]

Olha ta de parabéns muito bem feita acho que nao sei nem se tem palavras pra elogiar que seria pouco ... ta de parabéns